Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and navigation receiver assembly*1 or radio and display receiver assembly*2 are not normal.

DTC Code DTC Detection Condition Trouble Area
C1621 Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2



*1: for Navigation Receiver Type

*2: for Radio and Display Type


WIRING DIAGRAM

E323599E05
1.354,1.177 1.698,1.385 0.344,0.208 10 false CA+ 3.271,1.708 3.51,1.917 0.24,0.208 10 false *3 4.552,1.708 4.792,1.917 0.24,0.208 10 false *3 3.698,1.708 3.938,1.917 0.24,0.208 10 false *3 2.427,1.708 2.667,1.917 0.24,0.208 10 false *3 2.854,1.708 3.094,1.917 0.24,0.208 10 false *3 4.125,1.708 4.365,1.917 0.24,0.208 10 false *3 1.188,1.594 1.656,1.802 0.469,0.208 10 false CGND 5.563,1.167 5.906,1.375 0.344,0.208 10 false CB+ 5.365,1.104 5.708,1.313 0.344,0.208 10 false 6 5.365,1.521 5.708,1.729 0.344,0.208 10 false 5 5.552,1.594 6.021,1.802 0.469,0.208 10 false CGND 0.344,1.969 0.813,2.177 0.469,0.208 10 false H55 0.354,2.115 2.625,2.323 2.271,0.208 10 false Navigation Receiver Assembly 0.083,0.073 4.052,0.281 3.969,0.208 12 false for Navigation Receiver Type: 0.198,2.74 2.469,2.948 2.271,0.208 10 false *1: w/ Tire Carrier 0.188,3.031 2.458,3.24 2.271,0.208 10 false *2: w/o Tire Carrier 5.385,1.99 6.875,2.198 1.49,0.208 10 false v3*1, X10*2 5.396,2.146 6.875,2.594 1.479,0.448 10 false Rear Television Camera Assembly 0.208,3.313 1.76,3.521 1.552,0.208 10 false *3: Shielded 1.74,1.094 2.083,1.302 0.344,0.208 10 false 11 1.74,1.5 2.083,1.708 0.344,0.208 10 false 23

E323599E06
1.375,1.125 1.719,1.333 0.344,0.208 10 false CA+ 3.271,1.708 3.51,1.917 0.24,0.208 10 false *3 4.552,1.708 4.792,1.917 0.24,0.208 10 false *3 3.698,1.708 3.938,1.917 0.24,0.208 10 false *3 2.417,1.708 2.656,1.917 0.24,0.208 10 false *3 2.844,1.708 3.083,1.917 0.24,0.208 10 false *3 4.125,1.708 4.365,1.917 0.24,0.208 10 false *3 1.208,1.542 1.677,1.75 0.469,0.208 10 false CGND 5.563,1.125 5.906,1.333 0.344,0.208 10 false CB+ 5.365,1.052 5.708,1.26 0.344,0.208 10 false 6 5.365,1.469 5.708,1.677 0.344,0.208 10 false 5 5.552,1.542 6.021,1.75 0.469,0.208 10 false CGND 0.417,1.917 0.885,2.125 0.469,0.208 10 false H50 0.427,2.063 2.188,2.385 1.76,0.323 10 false Radio and Display Receiver Assembly 0.083,0.073 4.052,0.281 3.969,0.208 12 false for Radio and Display Type: 0.167,2.771 2.438,2.979 2.271,0.208 10 false *1: w/ Tire Carrier 0.156,3.063 2.427,3.271 2.271,0.208 10 false *2: w/o Tire Carrier 5.385,1.99 6.875,2.198 1.49,0.208 10 false v3*1, X10*2 5.396,2.146 6.896,2.594 1.5,0.448 10 false Rear Television Camera Assembly 0.188,3.354 1.74,3.563 1.552,0.208 10 false *3: Shielded 1.75,1.042 2.094,1.25 0.344,0.208 10 false 11 1.76,1.448 2.104,1.656 0.344,0.208 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point" (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).



PROCEDURE

1.CHECK DTC OUTPUT


Result
Result Proceed to
No DTC is output A
DTC is output (for Navigation Receiver Type) B
DTC is output (for Radio and Display Type) C


A

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)

C

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H55 navigation receiver assembly connector.


b.

Disconnect the v3*1 or X10*2 rear television camera assembly connector.

*1: w/ Tire Carrier

*2: w/o Tire Carrier



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier:
Tester Connection Condition Specified Condition
H55-11 (CA+) - v3-6 (CB+) Always Below 1 Ω
H55-23 (CGND) - v3-5 (CGND) Always Below 1 Ω
H55-11 (CA+) - H55-23 (CGND) Always 10 kΩ or higher
H55-11 (CA+) or v3-6 (CB+) - Body ground Always 10 kΩ or higher
H55-23 (CGND) or v3-5 (CGND) - Body ground Always Below 1 Ω

w/o Tire Carrier:
Tester Connection Condition Specified Condition
H55-11 (CA+) - X10-6 (CB+) Always Below 1 Ω
H55-23 (CGND) - X10-5 (CGND) Always Below 1 Ω
H55-11 (CA+) - H55-23 (CGND) Always 10 kΩ or higher
H55-11 (CA+) or X10-6 (CB+) - Body ground Always 10 kΩ or higher
H55-23 (CGND) or X10-5 (CGND) - Body ground Always Below 1 Ω




OK

3.CHECK NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)
a.
U170680E02
0.75,1.75 1,1.75 1,1.75 1.24,1.302 true 1.24,1.094 1,0.667 1,0.667 0.75,0.667 true 0.323,1.677 0.781,1.844 0.458,0.167 10 false CGND 1.552,0.167 1.823,0.344 0.271,0.177 10 false H55 0.042,0.021 0.313,0.229 0.271,0.208 10 false *a 0.427,0.583 0.74,0.771 0.313,0.188 10 false CA+

Remove the navigation receiver assembly with the connector still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H55-11 (CA+) - H55-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V


Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)


Result
Result Proceed to
OK A
NG (w/ Tire Carrier) B
NG (w/o Tire Carrier) C


A

B

C

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H50 radio and display receiver assembly connector.


b.

Disconnect the v3*1 or X10*2 rear television camera assembly connector.

*1: w/ Tire Carrier

*2: w/o Tire Carrier



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier:
Tester Connection Condition Specified Condition
H50-11 (CA+) - v3-6 (CB+) Always Below 1 Ω
H50-23 (CGND) - v3-5 (CGND) Always Below 1 Ω
H50-11 (CA+) - H50-23 (CGND) Always 10 kΩ or higher
H50-11 (CA+) or v3-6 (CB+) - Body ground Always 10 kΩ or higher
H50-23 (CGND) or v3-5 (CGND) - Body ground Always Below 1 Ω

w/o Tire Carrier:
Tester Connection Condition Specified Condition
H50-11 (CA+) - X10-6 (CB+) Always Below 1 Ω
H50-23 (CGND) - X10-5 (CGND) Always Below 1 Ω
H50-11 (CA+) - H50-23 (CGND) Always 10 kΩ or higher
H50-11 (CA+) or X10-6 (CB+) - Body ground Always 10 kΩ or higher
H50-23 (CGND) or X10-5 (CGND) - Body ground Always Below 1 Ω




OK

5.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U170680E03
0.75,1.75 1,1.75 1,1.75 1.24,1.302 true 1.24,1.094 1,0.667 1,0.667 0.75,0.667 true 0.323,1.677 0.781,1.844 0.458,0.167 10 false CGND 1.552,0.167 1.823,0.344 0.271,0.177 10 false H50 0.042,0.021 0.313,0.229 0.271,0.208 10 false *a 0.427,0.583 0.74,0.771 0.313,0.188 10 false CA+

Remove the radio and display receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H50-11 (CA+) - H50-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)


Result
Result Proceed to
OK A
NG (w/ Tire Carrier) B
NG (w/o Tire Carrier) C


A

B

C