Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU) › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261016 PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU) C

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM(for Camera built-in ECU)  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the navigation receiver assembly*1 or radio and display receiver assembly*2 judges that the signals or signal lines between the rear television camera assembly, and the navigation receiver assembly*1 or radio and display receiver assembly*2 are not normal as a result of its self check.

DTC Code DTC Detection Condition Trouble Area
C1622 Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

Rear television camera assembly



*1: for Navigation Receiver Type

*2: for Radio and Display Type


WIRING DIAGRAM

E323600E03
5.365,2.729 6.906,3.104 1.542,0.375 10 false Rear Television Camera Assembly 5.365,2.552 6.969,2.729 1.604,0.177 10 false v3*1, x10*2 0.969,2.688 2.198,3.146 1.229,0.458 10 false Navigation Receiver Assembly 0.271,4.375 1.25,4.542 0.979,0.167 10 false *3: Shielded 0.271,4.094 1.583,4.26 1.313,0.167 10 false *2: w/o Tire Carrier 0.271,3.813 1.583,3.979 1.313,0.167 10 false *1: w/ Tire Carrier 0.969,2.531 1.438,2.708 0.469,0.177 10 false H55 5.563,2.167 6.281,2.344 0.719,0.177 10 false CGND 5.542,1.646 6.26,1.823 0.719,0.177 10 false CV- 5.542,1.146 6.26,1.323 0.719,0.177 10 false CV+ 5.542,0.656 6.26,0.833 0.719,0.177 10 false CB+ 1.521,2.146 2.24,2.323 0.719,0.177 10 false CGND 1.781,1.646 2.5,1.823 0.719,0.177 10 false V- 1.74,1.146 1.958,1.323 0.219,0.177 10 false V+ 1.646,0.646 2.365,0.823 0.719,0.177 10 false CA+ 5.354,2.031 6.073,2.208 0.719,0.177 10 false 5 5.344,1.552 6.063,1.729 0.719,0.177 10 false 2 5.344,1.042 6.063,1.219 0.719,0.177 10 false 3 5.344,0.542 5.656,0.719 0.313,0.177 10 false 6 2.063,2.031 2.781,2.208 0.719,0.177 10 false 23 2.635,2.302 2.958,2.479 0.323,0.177 10 false *3 3.063,2.302 3.385,2.479 0.323,0.177 10 false *3 3.5,2.302 3.823,2.479 0.323,0.177 10 false *3 3.896,2.302 4.219,2.479 0.323,0.177 10 false *3 4.354,2.302 4.677,2.479 0.323,0.177 10 false *3 4.781,2.302 5.104,2.479 0.323,0.177 10 false *3 2.073,1.563 2.792,1.74 0.719,0.177 10 false 24 2.063,1.052 2.781,1.229 0.719,0.177 10 false 12 2.052,0.531 2.771,0.708 0.719,0.177 10 false 11 0.073,0 2.708,0.333 2.635,0.333 12 false for Navigation Receiver Type:

E323600E04
5.438,2.729 6.979,3.104 1.542,0.375 10 false Rear Television Camera Assembly 5.438,2.552 7.042,2.729 1.604,0.177 10 false v3*1, X10*2 0.719,2.677 2.406,3.104 1.688,0.427 10 false Radio and Display Receiver Assembly 0.271,4.375 1.25,4.542 0.979,0.167 10 false *3: Shielded 0.271,4.094 1.583,4.26 1.313,0.167 10 false *2: w/o Tire Carrier 0.271,3.813 1.583,3.979 1.313,0.167 10 false *1: w/ Tire Carrier 0.75,2.521 1.219,2.698 0.469,0.177 10 false H50 0.073,0.021 2.51,0.292 2.438,0.271 12 false for Radio and Display Type: 5.573,2.167 6.292,2.344 0.719,0.177 10 false CGND 5.552,1.646 6.271,1.823 0.719,0.177 10 false CV- 5.552,1.146 6.271,1.323 0.719,0.177 10 false CV+ 5.552,0.656 6.271,0.833 0.719,0.177 10 false CB+ 1.542,2.146 2.26,2.323 0.719,0.177 10 false CGND 1.802,1.646 2.521,1.823 0.719,0.177 10 false V- 1.76,1.146 1.979,1.323 0.219,0.177 10 false V+ 1.677,0.646 2.396,0.823 0.719,0.177 10 false CA+ 5.365,2.031 6.083,2.208 0.719,0.177 10 false 5 5.354,1.552 6.073,1.729 0.719,0.177 10 false 2 5.354,1.042 6.073,1.219 0.719,0.177 10 false 3 5.354,0.542 5.667,0.719 0.313,0.177 10 false 6 2.094,2.031 2.813,2.208 0.719,0.177 10 false 23 2.104,1.563 2.823,1.74 0.719,0.177 10 false 24 2.094,1.052 2.813,1.229 0.719,0.177 10 false 12 2.073,0.531 2.792,0.708 0.719,0.177 10 false 11 2.677,2.281 3,2.458 0.323,0.177 10 false *3 3.104,2.281 3.427,2.458 0.323,0.177 10 false *3 3.542,2.281 3.865,2.458 0.323,0.177 10 false *3 3.938,2.281 4.26,2.458 0.323,0.177 10 false *3 4.396,2.281 4.719,2.458 0.323,0.177 10 false *3 4.823,2.281 5.146,2.458 0.323,0.177 10 false *3

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point" (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM (for Camera built-in ECU)>CALIBRATION).



PROCEDURE

1.CHECK DTC OUTPUT


Result
Result Proceed to
No DTC is output A
DTC is output (for Navigation Receiver Type) B
DTC is output (for Radio and Display Type) C


A

B

2.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

C

5.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the v3*1 or X10*2 rear television camera assembly connector.

*1: w/ Tire Carrier

*2: w/o Tire Carrier



b.

Disconnect the H55 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier:
Tester Connection Condition Specified Condition
v3-6 (CB+) - H55-11 (CA+) Always Below 1 Ω
v3-3 (CV+) - H55-12 (V+) Always Below 1 Ω
v3-2 (CV-) - H55-24 (V-) Always Below 1 Ω
v3-5 (CGND) - H55-23 (CGND) Always Below 1 Ω
v3-6 (CB+) or H55-11 (CA+) - Body ground Always 10 kΩ or higher
v3-3 (CV+) or H55-12 (V+) - Body ground Always 10 kΩ or higher
v3-2 (CV-) or H55-24 (V-) - Body ground Always 10 kΩ or higher
v3-5 (CGND) or H55-23 (CGND) - Body ground Always Below 1 Ω

w/o Tire Carrier:
Tester Connection Condition Specified Condition
X10-6 (CB+) - H55-11 (CA+) Always Below 1 Ω
X10-3 (CV+) - H55-12 (V+) Always Below 1 Ω
X10-2 (CV-) - H55-24 (V-) Always Below 1 Ω
X10-5 (CGND) - H55-23 (CGND) Always Below 1 Ω
X10-6 (CB+) or H55-11 (CA+) - Body ground Always 10 kΩ or higher
X10-3 (CV+) or H55-12 (V+) - Body ground Always 10 kΩ or higher
X10-2 (CV-) or H55-24 (V-) - Body ground Always 10 kΩ or higher
X10-5 (CGND) or H55-23 (CGND) - Body ground Always Below 1 Ω




OK

3.CHECK NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NAVIGATION RECEIVER ASSEMBLY (CA+, CGND)
a.
U170680E02
0.75,1.75 1,1.75 1,1.75 1.24,1.302 true 1.24,1.094 1,0.667 1,0.667 0.75,0.667 true 0.323,1.677 0.781,1.844 0.458,0.167 10 false CGND 1.552,0.167 1.823,0.344 0.271,0.177 10 false H55 0.042,0.021 0.313,0.229 0.271,0.208 10 false *a 0.427,0.583 0.74,0.771 0.313,0.188 10 false CA+

Remove the navigation receiver assembly with the connector still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H55-11 (CA+) - H55-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H55-23 (CGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)


OK

4.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

4.CHECK REAR TELEVISION CAMERA ASSEMBLY
U170561E02
0.813,1.354 0.74,0.885 0.74,0.885 0.646,0.885 false 0.813,1.49 0.688,2.021 0.688,2.021 0.594,2.021 false 3.01,1.781 2.823,2.281 false 3.104,1.708 3.229,2.302 false 5.333,1.677 5.135,2.208 false 5.417,1.635 5.542,2.219 false 1.135,0.396 1.469,0.615 0.333,0.219 10 false H55 2.323,1.333 2.771,1.563 0.448,0.229 10 false GND 4.583,1.281 5.031,1.51 0.448,0.229 10 false GND 0.115,0.167 0.333,0.385 0.219,0.219 10 false *a 2.76,0.26 2.979,0.479 0.219,0.219 10 false *b 5.073,0.26 5.292,0.479 0.219,0.219 10 false *c 2.74,2.302 2.958,2.521 0.219,0.219 10 false *d 3.167,2.313 3.385,2.531 0.219,0.219 10 false *e 5.042,2.24 5.26,2.458 0.219,0.219 10 false *d 5.469,2.25 5.688,2.469 0.219,0.219 10 false *e 0.406,0.792 0.74,1 0.333,0.208 10 false V+ 0.406,1.938 0.74,2.146 0.333,0.208 10 false V-

Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -

a.

Remove the navigation receiver assembly with the connector still connected (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


Measurement Condition
Item Content
Measurement terminal H55-12 (V+) - H55-24 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image.
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



OK:

Waveform is as shown in the illustration.



Result
Result Proceed to
OK A
NG (w/ Tire Carrier) B
NG (w/o Tire Carrier) C


A

B

C

5.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the v3*1 or X10*2 rear television camera assembly connector.

*1: w/ Tire Carrier

*2: w/o Tire Carrier



b.

Disconnect the H50 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier:
Tester Connection Condition Specified Condition
v3-6 (CB+) - H50-11 (CA+) Always Below 1 Ω
v3-3 (CV+) - H50-12 (V+) Always Below 1 Ω
v3-2 (CV-) - H50-24 (V-) Always Below 1 Ω
v3-5 (CGND) - H50-23 (CGND) Always Below 1 Ω
v3-6 (CB+) or H50-11 (CA+) - Body ground Always 10 kΩ or higher
v3-3 (CV+) or H50-12 (V+) - Body ground Always 10 kΩ or higher
v3-2 (CV-) or H50-24 (V-) - Body ground Always 10 kΩ or higher
v3-5 (CGND) or H50-23 (CGND) - Body ground Always Below 1 Ω

w/o Tire Carrier:
Tester Connection Condition Specified Condition
X10-6 (CB+) - H50-11 (CA+) Always Below 1 Ω
X10-3 (CV+) - H50-12 (V+) Always Below 1 Ω
X10-2 (CV-) - H50-24 (V-) Always Below 1 Ω
X10-5 (CGND) - H50-23 (CGND) Always Below 1 Ω
X10-6 (CB+) or H50-11 (CA+) - Body ground Always 10 kΩ or higher
X10-3 (CV+) or H50-12 (V+) - Body ground Always 10 kΩ or higher
X10-2 (CV-) or H50-24 (V-) - Body ground Always 10 kΩ or higher
X10-5 (CGND) or H50-23 (CGND) - Body ground Always Below 1 Ω




OK

6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (CA+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (CA+, CGND)
a.
U170680E03
0.75,1.75 1,1.75 1,1.75 1.24,1.302 true 1.24,1.094 1,0.667 1,0.667 0.75,0.667 true 0.323,1.677 0.781,1.844 0.458,0.167 10 false CGND 1.552,0.167 1.823,0.344 0.271,0.177 10 false H50 0.042,0.021 0.313,0.229 0.271,0.208 10 false *a 0.427,0.583 0.74,0.771 0.313,0.188 10 false CA+

Remove the radio and display receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H50-11 (CA+) - H50-23 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H50-23 (CGND) - Body ground Always Below 1 Ω



Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)


OK

7.CHECK REAR TELEVISION CAMERA ASSEMBLY

NG

7.CHECK REAR TELEVISION CAMERA ASSEMBLY
U170562E02
0.813,1.354 0.74,0.885 0.74,0.885 0.646,0.885 false 0.813,1.5 0.688,2.031 0.688,2.031 0.594,2.031 false 3.01,1.802 2.823,2.302 false 3.104,1.708 3.229,2.302 false 5.333,1.688 5.135,2.219 false 5.417,1.635 5.542,2.219 false 1.135,0.417 1.469,0.635 0.333,0.219 10 false H50 2.323,1.344 2.771,1.573 0.448,0.229 10 false GND 4.583,1.281 5.031,1.51 0.448,0.229 10 false GND 0.115,0.167 0.333,0.385 0.219,0.219 10 false *a 2.76,0.26 2.979,0.479 0.219,0.219 10 false *b 5.073,0.26 5.292,0.479 0.219,0.219 10 false *c 2.74,2.323 2.958,2.542 0.219,0.219 10 false *d 3.167,2.323 3.385,2.542 0.219,0.219 10 false *e 5.042,2.24 5.26,2.458 0.219,0.219 10 false *d 5.469,2.24 5.688,2.458 0.219,0.219 10 false *e 0.406,0.813 0.74,1.021 0.333,0.208 10 false V+ 0.406,1.948 0.74,2.156 0.333,0.208 10 false V-

Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)
*b Waveform 1
*c Waveform 2 *d Synchronization Signal
*e Video Waveform - -

a.

Remove the radio and display receiver assembly with the connector still connected (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


Measurement Condition
Item Content
Measurement terminal H50-12 (V+) - H50-24 (V-)
Measurement setting 200 mV/DIV., 50 μsec./DIV.
Condition Waveform 1: Engine starts, shift lever in R, camera lens is not covered, displaying an image.
Waveform 2: Engine starts, shift lever in R, camera lens is covered, blacking out the screen.

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is on (ACC).



OK:

Waveform is as shown in the illustration.



Result
Result Proceed to
OK A
NG (w/ Tire Carrier) B
NG (w/o Tire Carrier) C


A

B

C