Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U0265  Lost Communication with Parking Assist Monitor Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0265 There is no communication from the rear television camera assembly.
·

Power source or inside rear television camera assembly

·

Rear television camera assembly CAN branch wire or connector

·

Rear television camera assembly

·

Navigation receiver assembly

·

Radio and display receiver assembly



For vehicles with a camera built-in ECU.


WIRING DIAGRAM

C329324E01
4.855,4.293 5.958,4.469 1.103,0.176 10 v3*1, X10*2 4.855,4.452 7.101,4.816 2.246,0.364 10 Rear Television Camera Assembly 0.119,1.692 0.557,1.868 0.437,0.176 10 G133 0.089,3.569 0.527,3.746 0.437,0.176 10 H55 0.119,1.852 1.774,2.028 1.655,0.176 10 No. 2 Junction Connector 5.62,0.919 6.524,1.153 0.904,0.235 10 CANH*1, H*2 1.581,0.825 1.690,0.979 0.109,0.154 10 1 5.392,0.79 5.573,0.944 0.181,0.154 10 4 5.392,1.328 5.573,1.482 0.181,0.154 10 1 5.392,2.628 5.584,2.781 0.192,0.154 10 6 5.392,3.14 5.595,3.293 0.203,0.154 10 5 0.089,3.733 2.091,3.963 2.002,0.230 10 Navigation Receiver Assembly 1.581,1.279 1.775,1.432 0.194,0.153 10 12 1.581,2.624 1.775,2.777 0.194,0.153 10 11 1.581,3.156 1.775,3.310 0.194,0.153 10 23 5.62,1.45 6.549,1.626 0.929,0.176 10 CANL*1, L*2 5.676,2.742 6.142,2.919 0.466,0.176 10 CB+ 5.676,3.252 6.142,3.429 0.466,0.176 10 CGND 1.109,2.742 1.575,2.919 0.466,0.176 10 CA+ 0.969,3.252 1.435,3.429 0.466,0.176 10 CGND 2.219,3.397 2.424,3.569 0.205,0.172 10 *3 4.573,3.397 4.778,3.569 0.205,0.172 10 *3 4.096,3.397 4.301,3.569 0.205,0.172 10 *3 3.62,3.397 3.825,3.569 0.205,0.172 10 *3 3.172,3.397 3.377,3.569 0.205,0.172 10 *3 2.695,3.397 2.900,3.569 0.205,0.172 10 *3 0.174,4.721 2.175,4.951 2.002,0.230 10 *1: w/ Tire Carrier 0.174,5.001 2.175,5.231 2.002,0.230 10 *2: w/o Tire Carrier 0.174,5.281 2.175,5.511 2.002,0.230 10 *3: Shielded 0.068,0.002 4.235,0.433 4.167,0.431 12 w/ Navigation System (for Navigation Receiver Type):

C329324E02
4.855,4.293 5.958,4.469 1.103,0.176 10 v3*1, X10*2 4.855,4.452 7.101,4.816 2.246,0.364 10 Rear Television Camera Assembly 0.119,1.692 0.557,1.868 0.437,0.176 10 G133 0.089,3.569 0.527,3.746 0.437,0.176 10 H50 0.119,1.852 1.774,2.028 1.655,0.176 10 No. 2 Junction Connector 5.62,0.919 6.524,1.153 0.904,0.235 10 CANH*1, H*2 1.581,0.825 1.690,0.979 0.109,0.154 10 1 5.392,0.79 5.573,0.944 0.181,0.154 10 4 5.392,1.328 5.573,1.482 0.181,0.154 10 1 5.392,2.628 5.584,2.781 0.192,0.154 10 6 5.392,3.14 5.595,3.293 0.203,0.154 10 5 0.089,3.733 2.541,4.118 2.451,0.385 10 Radio and Display Receiver Assembly 1.581,1.279 1.775,1.432 0.194,0.153 10 12 1.581,2.624 1.775,2.777 0.194,0.153 10 11 1.581,3.156 1.775,3.310 0.194,0.153 10 23 5.62,1.45 6.549,1.626 0.929,0.176 10 CANL*1, L*2 5.676,2.742 6.142,2.919 0.466,0.176 10 CB+ 5.676,3.252 6.142,3.429 0.466,0.176 10 CGND 1.109,2.742 1.575,2.919 0.466,0.176 10 CA+ 0.969,3.252 1.435,3.429 0.466,0.176 10 CGND 2.219,3.397 2.424,3.569 0.205,0.172 10 *3 4.573,3.397 4.778,3.569 0.205,0.172 10 *3 4.096,3.397 4.301,3.569 0.205,0.172 10 *3 3.62,3.397 3.825,3.569 0.205,0.172 10 *3 3.172,3.397 3.377,3.569 0.205,0.172 10 *3 2.695,3.397 2.900,3.569 0.205,0.172 10 *3 0.174,4.721 2.175,4.951 2.002,0.230 10 *1: w/ Tire Carrier 0.174,5.001 2.175,5.231 2.002,0.230 10 *2: w/o Tire Carrier 0.174,5.281 2.175,5.511 2.002,0.230 10 *3: Shielded 0.068,0.002 5.957,0.433 5.889,0.431 12 w/ Navigation System (for Radio and Display Type) or w/o Navigation System:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE)
a.
U170484E01
1.601,1.941 1.803,2.733 1.803,2.733 1.898,2.733 false 1.589,1.601 1.783,0.812 1.783,0.812 1.871,0.812 false 1.935,0.725 2.888,0.903 0.953,0.178 10 CANL*A, L*B 1.969,2.646 2.912,2.824 0.943,0.177 10 CANH*A, H*B 0.13,0.082 0.691,0.259 0.561,0.177 10 *a 0.298,0.988 0.610,1.166 0.313,0.178 10 v3 0.706,1.004 0.947,1.181 0.242,0.177 10 *A 0.229,1.535 0.542,1.713 0.313,0.178 10 X10 0.706,1.568 0.961,1.746 0.256,0.177 10 *B

Disconnect the rear television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier
Tester Connection Switch Condition Specified Condition
v3-4 (CANH) - v3-1 (CANL) Engine switch off 54 to 69 Ω

w/o Tire Carrier
Tester Connection Switch Condition Specified Condition
X10-4 (H) - X10-1 (L) Engine switch off 54 to 69 Ω


Text in Illustration
*A w/ Tire Carrier
*B w/o Tire Carrier
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Result
Result Proceed to
OK (w/ Navigation System [for Navigation Receiver Type]) A
OK (w/ Navigation System [for Radio and Display Type] or w/o Navigation System) B
NG C


A

3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - BATTERY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - BATTERY AND BODY GROUND)

C

REPAIR OR REPLACE REAR TELEVISION CAMERA ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL, H, L)

3.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170485E02
1.729,1.969 2.052,2.76 2.052,2.76 2.146,2.76 true 1.969,1.844 2.604,0.844 2.604,0.844 2.688,0.844 true 2.74,0.771 3.115,0.948 0.375,0.177 10 false CB+ 2.198,2.677 2.677,2.854 0.479,0.177 10 false CGND 0.125,0.083 0.688,0.26 0.563,0.177 10 false *a 0.302,0.99 0.615,1.167 0.313,0.177 10 false v3 0.708,1 0.948,1.177 0.24,0.177 10 false *A 0.229,1.531 0.542,1.708 0.313,0.177 10 false X10 0.708,1.573 0.969,1.75 0.26,0.177 10 false *B

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-5 (CGND) - Body ground Always Below 1 Ω

w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-5 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Tire Carrier
Tester Connection Switch Condition Specified Condition
v3-6 (CB+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V

w/ Tire Carrier
Tester Connection Switch Condition Specified Condition
X10-6 (CB+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V



Text in Illustration
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the H55 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-6 (CB+) - H55-11 (CA+) Always Below 1 Ω
v3-5 (CGND) - H55-23 (CGND) Always Below 1 Ω
v3-6 (CB+) or H55-11 (CA+) - Body ground Always 10 kΩ or higher
v3-5 (CGND) or H55-23 (CGND) - Body ground Always 10 kΩ or higher

w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-6 (CB+) - H55-11 (CA+) Always Below 1 Ω
X10-5 (CGND) - H55-23 (CGND) Always Below 1 Ω
X10-6 (CB+) or H55-11 (CA+) - Body ground Always 10 kΩ or higher
X10-5 (CGND) or H55-23 (CGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170485E03
1.74,1.958 2.063,2.75 2.063,2.75 2.156,2.75 true 1.948,1.844 2.583,0.844 2.583,0.844 2.667,0.844 true 2.708,0.771 3.083,0.948 0.375,0.177 10 false CB+ 2.198,2.667 2.677,2.844 0.479,0.177 10 false CGND 0.125,0.083 0.688,0.26 0.563,0.177 10 false *a 0.302,0.99 0.615,1.167 0.313,0.177 10 false v3 0.708,1 0.948,1.177 0.24,0.177 10 false *A 0.229,1.531 0.542,1.708 0.313,0.177 10 false X10 0.708,1.573 0.969,1.75 0.26,0.177 10 false *B

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-5 (CGND) - Body ground Always Below 1 Ω

w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-5 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ Tire Carrier
Tester Connection Switch Condition Specified Condition
v3-6 (CB+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V

w/ Tire Carrier
Tester Connection Switch Condition Specified Condition
X10-6 (CB+) - Body ground Engine switch on (ACC) 5.5 to 7.05 V



Text in Illustration
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H50 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-6 (CB+) - H50-11 (CA+) Always Below 1 Ω
v3-5 (CGND) - H50-23 (CGND) Always Below 1 Ω
v3-6 (CB+) or H50-11 (CA+) - Body ground Always 10 kΩ or higher
v3-5 (CGND) or H50-23 (CGND) - Body ground Always 10 kΩ or higher

w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-6 (CB+) - H50-11 (CA+) Always Below 1 Ω
X10-5 (CGND) - H50-23 (CGND) Always Below 1 Ω
X10-6 (CB+) or H50-11 (CA+) - Body ground Always 10 kΩ or higher
X10-5 (CGND) or H50-23 (CGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR