Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2282  Vehicle Speed Signal Malfunction  B2283  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The power management control ECU and the combination meter are connected by a cable and the CAN communication lines. This DTC is stored when the vehicle speed signal information from the cable and the vehicle speed signal information from the CAN communication line are inconsistent.

HINT:

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code DTC Detection Condition Trouble Area
B2282 The vehicle speed signal information from the cable and the vehicle speed signal information from the CAN communication line are inconsistent.
·

CAN communication system

·

Power management control ECU

·

Meter/gauge system

·

Harness or connector



The skid control ECU converts signals from the speed sensor into 4-pulse signals and sends them to the combination meter. After these signals are converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, they are then transmitted to the power management control ECU. The power management control ECU determines the vehicle speed based on the frequencies of these pulse signals.

DTC Code DTC Detection Condition Trouble Area
B2283 Both conditions are met:
·

The vehicle speed decreases significantly.

·

The vehicle speed does not correspond with the engine speed.


·

Power management control ECU

·

Meter/gauge system

·

Skid control ECU

·

Speed sensor

·

Harness or connector



C166257E08
2.923,1.334 4.143,1.718 1.220,0.384 10 Combination Meter Assembly 0.43,4.416 2.179,4.600 1.749,0.185 10 : CAN Communication Line 4.944,2.563 6.388,2.748 1.444,0.185 10 B2282 Detection Area 2.972,3.623 4.416,3.808 1.444,0.185 10 B2283 Detection Area 0.576,3.025 1.586,3.209 1.010,0.185 10 Speed Sensor 0.498,1.423 1.653,1.608 1.156,0.185 10 Skid Control ECU 2.036,1.081 2.624,1.266 0.589,0.185 10 4 Pulses 4.558,1.081 5.146,1.266 0.589,0.185 10 4 Pulses 5.436,1.034 6.775,1.553 1.339,0.520 10 Power Management Control ECU

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls its respective system based on the pulse signal.

·

If a short circuit occurs in an ECU, all systems related to the components in the diagram above will not operate normally.



WIRING DIAGRAM

A214470E02
2.55,1.199 2.797,1.374 0.247,0.174 10 32 2.209,1.326 2.455,1.501 0.245,0.174 10 +S 3.943,1.335 4.287,1.510 0.344,0.174 10 SPD 0.622,0.505 1.449,0.679 0.827,0.174 10 from Battery 1.168,1.978 3.019,2.153 1.851,0.174 10 Combination Meter Assembly 2.654,0.698 2.992,0.872 0.338,0.174 10 AM2 3.943,0.531 4.328,0.705 0.385,0.174 10 AM21 3.943,0.925 4.328,1.099 0.385,0.174 10 AM22 3.481,2.029 5.770,2.290 2.289,0.260 10 Power Management Control ECU 4.391,1.514 4.826,1.689 0.435,0.174 10 GND2 4.493,1.127 4.856,1.301 0.363,0.174 10 GND 3.743,0.458 3.922,0.632 0.179,0.174 10 2 3.743,0.804 3.922,0.979 0.179,0.174 10 1 4.915,1.023 5.255,1.197 0.340,0.174 10 6 4.921,1.419 5.261,1.593 0.340,0.174 10 5 0.845,2.271 2.590,2.445 1.745,0.174 10 : CAN Communication Line 3.481,1.844 3.806,2.019 0.325,0.174 10 G51 3.707,1.211 3.943,1.385 0.236,0.174 10 23 1.168,1.819 1.493,1.994 0.325,0.174 10 G6

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMBINATION METER)
a.

Disconnect the G51 power management control ECU connector.


b.

Disconnect the G6 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-23 (SPD) - G6-32 (+S) Always Below 1 Ω
G51-23 (SPD) - Body ground Always 10 kΩ or higher




OK

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Signal Vehicle speed signal / Stop or Run Stop: Vehicle stopped
Run: Vehicle driven (5 km/h (3 mph) or higher)
-

OK:

Stop (vehicle stopped) or Run (vehicle driven) appears on the screen according the vehicle speed.




OK

GO TO METER/GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

5.CHECK POWER MANAGEMENT CONTROL ECU
5.CHECK POWER MANAGEMENT CONTROL ECU
a.

Using an oscilloscope, check the vehicle speed input signal waveform from the combination meter at the terminal of the power management control ECU.

U169908E01
0.135,0.091 0.337,0.251 0.202,0.160 10 *a 5.707,0.615 6.144,0.787 0.437,0.172 10 SPD 4.859,1.637 5.564,0.677 5.564,0.677 5.676,0.677 false 4.476,0.695 4.772,0.858 0.296,0.163 10 G51

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
- -


b.
C192841E01
2.904,1.727 3.296,1.945 0.392,0.218 10 GND

Check the signal waveform according to the condition(s) in the table below.

Standard Frequency:
Tester Connection Tool Setting Condition Specified Condition
G51-23 (SPD) - Body ground 5 V/DIV., 10 ms./DIV. Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph) Correct waveform as shown in illustration




OK

NG

GO TO METER/GAUGE SYSTEM (TERMINALS OF ECU)