Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B2660  Steering Wheel Switch Malfunction  


DESCRIPTION

This code is output when any steering pad switch is continuously on for a period of 60 seconds.

DTC Code DTC Detection Condition Trouble Area
B2660 The driving support switch control ECU detects a malfunction in the steering pad switch.
·

Harness or connector

·

Driving support switch control ECU

·

Spiral cable sub-assembly

·

Steering pad switch assembly



WIRING DIAGRAM

E201873E06
2.531,1.969 3.208,2.344 0.677,0.375 10 false G40 2.531,2.708 3.365,3.073 0.833,0.365 10 false G40 4.146,1.958 4.448,2.167 0.302,0.208 10 false z8 4.146,2.698 4.427,2.865 0.281,0.167 10 false z8 0.792,3.656 2.094,4.125 1.302,0.469 10 false G163*1, G76*2 0.781,3.823 3.167,4.021 2.385,0.198 10 false Driving Support Switch Control ECU 2.813,3.313 3.958,3.646 1.146,0.333 10 false Spiral Cable Sub-assembly 2.896,1.958 3.427,2.365 0.531,0.406 10 false DISP 2.906,2.708 3.646,2.969 0.74,0.26 10 false GND1 1.615,1.958 2.323,2.406 0.708,0.448 10 false SWI1 1.625,2.708 2.427,3.073 0.802,0.365 10 false SWI2 2.625,1.76 3.104,2.208 0.479,0.448 10 false 9 2.594,2.5 3.25,2.771 0.656,0.271 10 false 10 4.177,1.76 4.656,2.094 0.479,0.333 10 false 2 4.188,2.51 4.792,2.854 0.604,0.344 10 false 3 2.042,1.688 2.375,1.896 0.333,0.208 10 false 5*1 2.042,2.458 2.479,2.677 0.438,0.219 10 false 14*1 4.396,3.323 5.531,3.802 1.135,0.479 10 false Steering Pad Switch Assembly 2.042,1.875 2.323,2.073 0.281,0.198 10 false 3*2 2.063,2.625 2.406,2.833 0.344,0.208 10 false 4*2 4.448,1.875 4.917,2.063 0.469,0.188 10 false DISP 4.448,2.615 4.927,2.802 0.479,0.188 10 false GND1 0.115,4.167 4.698,4.365 4.583,0.198 10 false *1: for Automatic Transmission 0.115,4.385 4.24,4.583 4.125,0.198 10 false *2: for Manual Transmission

PROCEDURE

1.READ VALUE USING GTS

D-SEAT SW
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Wheel Menu Switch MENU switch/OFF or ON OFF: MENU switch off -
ON: MENU switch on
Steering Wheel Enter Switch ENTER switch/OFF or ON OFF: ENTER switch off -
ON: ENTER switch on
Steering Wheel Up Switch UP/DOWN UP switch/OFF or ON OFF: UP/DOWN UP switch off -
ON: UP/DOWN UP switch on
Steering Wheel Down Switch UP/DOWN DOWN switch/OFF or ON OFF: UP/DOWN DOWN switch off -
ON: UP/DOWN DOWN switch on

OK:

The value displayed on the intelligent tester changes with the actual steering pad switch operation.



OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).

U170658E01
5.311,0.294 5.671,0.442 0.359,0.148 10 DISP 5.328,0.724 5.745,0.873 0.418,0.148 10 GND1 4.675,0.928 5.183,0.354 5.183,0.354 5.264,0.354 false 4.786,0.928 5.22,0.788 5.22,0.788 5.286,0.788 false 5.051,2.466 5.338,1.612 5.338,1.612 5.411,1.612 false 5.338,2.569 5.705,2.129 5.705,2.129 5.855,2.129 false 4.164,0.562 4.363,0.710 0.199,0.148 10 *a 5.427,1.521 5.626,1.669 0.199,0.148 10 *b 5.873,2.054 6.461,2.202 0.588,0.148 10 *c, *d, *e 4.71,0.26 4.882,0.432 0.171,0.171 10 z8

Text in Illustration
*a Front view of wire harness connector
(to spiral cable sub-assembly)
*b MENU switch
*c ENTER switch *d UP/DOWN UP switch
*e UP/DOWN DOWN switch - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (DISP) - z8-3 (GND1) MENU switch pushed Below 2.5 Ω
ENTER switch pushed 313 to 346 Ω
UP/DOWN UP switch pushed 3049 to 3370 Ω
UP/DOWN DOWN switch pushed 959 to 1060 Ω
switch off 95 to 105 kΩ




OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT SWITCH CONTROL ECU)

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT SWITCH CONTROL ECU)
a.

Disconnect the G163*1 or G76*2 driving support switch control ECU connector.

*1: for Automatic Transmission

*2: for Manual Transmission



b.

Disconnect the G40 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission
Tester Connection Condition Specified Condition
G40-9 (DISP) - G163-5 (SWI1) Always Below 1 Ω
G40-10 (GND1) - G163-14 (SWI2) Always Below 1 Ω
G40-9 (DISP) - G40-2 (ECC) Always 10 kΩ or higher
G40-9 (DISP) - G40-4 (EAU) Always 10 kΩ or higher
G40-9 (DISP) -G40-10 (GND1) Always 10 kΩ or higher
G40-9 (DISP) - Body ground Always 10 kΩ or higher
G40-10 (GND1) - Body ground Always 10 kΩ or higher

for Manual Transmission
Tester Connection Condition Specified Condition
G40-9 (DISP) - G76-3 (SWI1) Always Below 1 Ω
G40-10 (GND1) - G76-4 (SWI2) Always Below 1 Ω
G40-9 (DISP) - G40-2 (ECC) Always 10 kΩ or higher
G40-9 (DISP) - G40-4 (EAU) Always 10 kΩ or higher
G40-9 (DISP) -G40-10 (GND1) Always 10 kΩ or higher
G40-9 (DISP) - Body ground Always 10 kΩ or higher
G40-10 (GND1) - Body ground Always 10 kΩ or higher




OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Set the spiral cable to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).

E349705E01
2.656,0.719 2.969,0.917 0.313,0.198 10 false *a 4.99,3.146 5.302,3.344 0.313,0.198 10 false *b

Text in Illustration
*a Connector A *b Connector B


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-9 Always Below 1 Ω
A-3 - B-10 Always Below 1 Ω
A-2 - A-3 Always 10 kΩ or higher
A-2 - A-6 Always 10 kΩ or higher
A-2 - A-8 Always 10 kΩ or higher
A-2 - Body ground Always 10 kΩ or higher
A-3 - Body ground Always 10 kΩ or higher




OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY