Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Rear Blower Motor Circuit  


DESCRIPTION

The rear blower with fan motor sub-assembly is operated by signals from the air conditioning amplifier. Rear blower motor speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM

E194806E10
0.719,2.906 1.031,3.063 0.313,0.156 10 false Q12 0.719,3.073 2.094,3.271 1.375,0.198 10 false Blower Motor Control 1.823,2.469 1.969,2.625 0.146,0.156 10 false 6 1.823,1.823 1.958,1.969 0.135,0.146 10 false 2 1.333,2.573 1.688,2.74 0.354,0.167 10 false GND 1.438,1.917 1.688,2.083 0.25,0.167 10 false VM 1.458,1.25 1.688,1.427 0.229,0.177 10 false +B 1.823,1.167 1.969,1.313 0.146,0.146 10 false 1 1.531,0.594 1.688,0.771 0.156,0.177 10 false SI 1.823,0.5 1.958,0.656 0.135,0.156 10 false 3 2.375,1.417 2.906,1.563 0.531,0.146 10 false A/C RR 3.698,1.26 4.51,1.458 0.813,0.198 10 false from Battery 3,2.438 3.135,2.583 0.135,0.146 10 false 2 3,3.073 3.146,3.219 0.146,0.146 10 false 1 3.167,2.615 3.458,2.771 0.292,0.156 10 false Q14 3.188,2.792 4.635,3.135 1.448,0.344 10 false Rear Blower with Fan Motor Sub-assembly 5.427,2.833 5.75,3 0.323,0.167 10 false G24 5.427,3 7.073,3.406 1.646,0.406 10 false Air Conditioning Amplifier Assembly 5.927,1.927 6.375,2.094 0.448,0.167 10 false RGND 5.573,1.813 5.792,1.958 0.219,0.146 10 false 20 5.927,0.563 6.375,0.729 0.448,0.167 10 false BLWH 5.573,0.49 5.792,0.635 0.219,0.146 10 false 22

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR BLOWER WITH FAN MOTOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the rear blower with fan motor sub-assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Rear Blower Motor Rear blower with fan motor sub-assembly Min.: 0, Max.: 31 -

OK:

Rear blower with fan motor sub-assembly operates and rear blower with fan motor sub-assembly speed changes.




OK

NG

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - BATTERY AND BODY GROUND)
a.
U116498E04
2.031,1.406 2.385,1.708 false 1.083,0.813 1.438,1.125 false 2.448,1.667 2.823,1.875 0.375,0.208 10 false GND 0.792,0.667 1.052,0.875 0.26,0.208 10 false +B 0.583,1.156 0.917,1.365 0.333,0.208 10 false Q12 0.115,0 0.375,0.208 0.26,0.208 10 false *a

Disconnect the Q12 control connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q12-1 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q12-6 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Blower Motor Control)


OK

3.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY
a.

Remove the rear blower with fan motor sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR BLOWER MOTOR>REMOVAL).


E194807

b.

Apply battery voltage to the rear blower with fan motor sub-assembly and check the operation of the rear blower with fan motor sub-assembly.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 2
Battery negative (-) → Terminal 1
Rear blower with fan motor sub-assembly operation is normal




OK

4.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER)

NG

REPLACE REAR BLOWER WITH FAN MOTOR SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G24 amplifier connector.


b.

Disconnect the Q12 control connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G24-22 (BLWH) - Q12-3 (SI) Always Below 1 Ω
G24-22 (BLWH) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - REAR BLOWER WITH FAN MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR CONTROL - REAR BLOWER WITH FAN MOTOR)
a.

Disconnect the Q12 control connector.


b.

Disconnect the Q14 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q12-2 (VM) - Q14-2 Always Below 1 Ω
Q12-2 (VM) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER WITH FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR BLOWER WITH FAN MOTOR - BODY GROUND)
a.
U116499E03
0.531,1.083 0.865,1.25 0.333,0.167 10 false Q14 0.188,0 0.396,0.167 0.208,0.167 10 false *a

Disconnect the Q14 motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q14-1 - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rear Blower with Fan Motor Sub-assembly)



OK

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U149247E01
0.169,0.03 0.358,0.195 0.189,0.165 10 *a 0.502,1.716 1.044,2.35 false 0.831,2.35 1.295,2.516 0.464,0.165 10 RGND 0.359,1.716 0.382,2.35 false 0.139,2.35 0.603,2.516 0.464,0.165 10 BLWH 0.471,0.722 0.792,0.887 0.321,0.165 10 G24

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G24-22 (BLWH) - G24-20 (RGND) Always 4.5 to 7 V


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

9.REPLACE BLOWER MOTOR CONTROL
8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.
U170769E02
0.365,1.417 0.365,2.313 0.365,2.313 0.458,2.313 false 0.521,1.427 0.521,1.969 0.521,1.969 0.615,1.969 false 0.583,0.458 1.01,0.646 0.427,0.188 10 false G24 0.5,2.229 1.01,2.385 0.51,0.156 10 false BLWH 0.646,1.875 1.156,2.031 0.51,0.156 10 false RGND 2.792,3.854 3.302,4.01 0.51,0.156 10 false GND 0.094,0.031 0.521,0.219 0.427,0.188 10 false *a

Remove the air conditioning amplifier assembly with its connectors still connected (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL).


b.

Using an oscilloscope, check the waveform.

Item Content
Terminal No. (Symbol) G24-22 (BLWH) - G24-20 (RGND)
Tool Setting 2 V/DIV., 500 μs/DIV.
Condition Ignition switch ON
Blower switch LO

OK:

Waveform is as shown in the illustration.


Text in Illustration
*a Component with harness connected
(Air Conditioning Amplifier Assembly)

HINT:

Waveform varies with the blower level.




OK

9.REPLACE BLOWER MOTOR CONTROL

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

9.REPLACE BLOWER MOTOR CONTROL
a.

Replace the blower motor control with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY).


b.

Operate the rear blower with fan motor sub-assembly to check that it functions properly.

OK:

Rear blower with fan motor sub-assembly operates normally.




OK

END (BLOWER MOTOR CONTROL IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY