Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Viscous Heater with Magnet Clutch Circuit  


DESCRIPTION

When the idle up switch assembly is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the idle up switch assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E323968E01
0.425,0.867 1.859,1.051 1.434,0.184 10 from IG1 NO.1 Relay 0.962,1.288 1.849,1.471 0.887,0.184 10 from Battery 2.737,1.017 3.106,1.201 0.369,0.184 10 IG1 2.583,1.437 3.229,1.621 0.647,0.184 10 VISCUS 3.624,1.666 4.271,1.850 0.647,0.184 10 VISCUS 3.376,0.751 3.569,0.934 0.193,0.184 10 1 3.376,1.171 3.569,1.355 0.193,0.184 10 5 4.315,0.751 4.508,0.934 0.193,0.184 10 2 5.324,0.751 5.554,0.934 0.230,0.184 10 16 5.576,0.877 5.964,1.060 0.387,0.184 10 MG+ 5.604,3.497 5.992,3.680 0.387,0.184 10 MG+ 4.315,1.171 4.508,1.355 0.193,0.184 10 3 5.352,2.124 5.545,2.307 0.193,0.184 10 1 5.352,3.385 5.545,3.568 0.193,0.184 10 1 4.876,1.353 5.263,1.537 0.387,0.184 10 G25 4.876,1.521 7.129,1.844 2.253,0.323 10 Air Conditioning Amplifier Assembly 4.876,2.67 5.263,2.854 0.387,0.184 10 C94 4.876,2.838 7.129,3.161 2.253,0.323 10 Viscous Heater with Magnet Clutch Assembly*1 4.876,3.917 5.263,4.101 0.387,0.184 10 r4 4.876,4.085 7.129,4.408 2.253,0.323 10 Viscous Heater with Magnet Clutch Assembly*2 0.332,3.922 1.691,4.105 1.360,0.184 10 *1: for 1KD-FTV 0.332,4.202 1.691,4.386 1.360,0.184 10 *2: for 1GD-FTV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (VISCOUS HEATER)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the viscous heater with magnet clutch assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Viscous Heater Viscous heater with magnet clutch assembly operation ON or OFF -

OK:

The display is as specified in the normal condition column.




OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)
2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)
a.

except 1GD-FTV, w/ Urea SCR System:

i.
E202090E01
0.083,0.041 0.336,0.211 0.253,0.170 10 *a 1.744,1.659 1.948,1.829 0.204,0.170 10 *1

Remove the VISCUS relay from the engine room No. 1 relay block, junction block.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
VISCUS relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
VISCUS relay terminal 2 - Body ground Always 11 to 14 V


Text in Illustration
*1 VISCUS Relay
*a Component without relay installed
(Engine Room No. 1 Relay Block, Junction Block)



b.

for 1GD-FTV, w/ Urea SCR System:

i.
E321120E02
0.063,0 0.49,0.25 0.427,0.25 10 false *a 0.844,1.146 1.271,1.396 0.427,0.25 10 false *1

Remove the VISCUS relay from the engine room No. 1 relay block, junction block.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
VISCUS relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
VISCUS relay terminal 2 - Body ground Always 11 to 14 V


Text in Illustration
*1 VISCUS Relay
*a Component without relay installed
(Engine Room No. 1 Relay Block, Junction Block)




OK

3.INSPECT VISCOUS HEATER RELAY (VISCUS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT VISCOUS HEATER RELAY (VISCUS)
a.

Remove the viscous heater relay (VISCUS) from engine room No. 1 relay block, junction block.



Result
Result Proceed to
OK (for 1KD-FTV) A
OK (for 1GD-FTV) B
NG C


A

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)

C

REPLACE VISCOUS HEATER RELAY (VISCUS)

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)
a.

Remove the VISCUS relay from the engine room No. 1 relay block, junction block.


b.

Disconnect the C94 viscous heater with magnet clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
VISCUS relay terminal 3 - C94-1 Always Below 1 Ω
VISCUS relay terminal 3 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the VISCUS relay from the engine room No. 1 relay block, junction block.


b.

Disconnect the G25 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
VISCUS relay terminal 2 - G25-16 (MG+) Always Below 1 Ω
VISCUS relay terminal 2 - Body ground Always 10 kΩ or higher




OK

6.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY
a.

Remove the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>REMOVAL).


b.

Inspect the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>INSPECTION).



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)
a.

Remove the VISCUS relay from the engine room No. 1 relay block, junction block.


b.

Disconnect the r4 viscous heater with magnet clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
VISCUS relay terminal 3 - r4-1 Always Below 1 Ω
VISCUS relay terminal 3 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the VISCUS relay from the engine room No. 1 relay block, junction block.


b.

Disconnect the G25 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
VISCUS relay terminal 2 - G25-16 (MG+) Always Below 1 Ω
VISCUS relay terminal 2 - Body ground Always 10 kΩ or higher




OK

9.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY
a.

Remove the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>REMOVAL).


b.

Inspect the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>INSPECTION).



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY