When the idle up switch assembly is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the idle up switch assembly is pushed, there may be a problem in the circuit shown below.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Select the Active Test, use the GTS to generate a control command, and then check that the viscous heater with magnet clutch assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Viscous Heater | Viscous heater with magnet clutch assembly operation | ON or OFF | - |
The display is as specified in the normal condition column.
OK
NG
except 1GD-FTV, w/ Urea SCR System:
Remove the viscous heater relay (VISCUS) from the engine room No. 1 relay block, junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| VISCUS relay terminal 5 - Body ground | Ignition switch ON | 11 to 14 V |
| VISCUS relay terminal 2 - Body ground | Always | 11 to 14 V |
| *1 | VISCUS Relay |
| *a | Component without relay installed
(Engine Room No. 1 Relay Block, Junction Block) |
for 1GD-FTV, w/ Urea SCR System:
Remove the viscous heater relay (VISCUS) from the engine room No. 1 relay block, junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| VISCUS relay terminal 5 - Body ground | Ignition switch ON | 11 to 14 V |
| VISCUS relay terminal 2 - Body ground | Always | 11 to 14 V |
| *1 | Viscous heater Relay (VISCUS) |
| *a | Component without relay installed
(Engine Room No. 1 Relay Block, Junction Block) |
OK
NG
Remove the viscous heater relay (VISCUS) from engine room No. 1 relay block, junction block.
Inspect the viscous heater relay (VISCUS) (See page Vehicle Interior>HEATING / AIR CONDITIONING>RELAY(w/ Viscous Heater)>ON-VEHICLE INSPECTION).
| Result | Proceed to |
|---|---|
| OK (for 1KD-FTV) | A |
| OK (for 1GD-FTV) | B |
| NG | C |
A
B
C
Remove the viscous heater relay (VISCUS) from the engine room No. 1 relay block, junction block.
Disconnect the C94 viscous heater with magnet clutch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Viscous heater relay (VISCUS) terminal 3 - C94-1 | Always | Below 1 Ω |
| Viscous heater relay (VISCUS) terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the viscous heater relay (VISCUS) from the engine room No. 1 relay block, junction block.
Disconnect the G25 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Viscous heater relay (VISCUS) terminal 2 - G25-16 (MG+) | Always | Below 1 Ω |
| Viscous heater relay (VISCUS) terminal 2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>REMOVAL).
Inspect the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>INSPECTION).
OK
NG
(See pageVehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>REMOVAL)
Remove the viscous heater relay (VISCUS) from the engine room No. 1 relay block, junction block.
Disconnect the r4 viscous heater with magnet clutch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Viscous heater relay (VISCUS) terminal 3 - r4-1 | Always | Below 1 Ω |
| Viscous heater relay (VISCUS) terminal 3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the viscous heater relay (VISCUS) from the engine room No. 1 relay block, junction block.
Disconnect the G25 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Viscous heater relay (VISCUS) terminal 2 - G25-16 (MG+) | Always | Below 1 Ω |
| Viscous heater relay (VISCUS) terminal 2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>REMOVAL).
Inspect the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>INSPECTION).
OK
NG
(See pageVehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>REMOVAL)