Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS(w/ Back Door Tire Carrier)
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261223 BACK DOOR GLASS(w/ Back Door Tire Carrier) A

WINDOW / GLASS  BACK DOOR GLASS(w/ Back Door Tire Carrier)  INSTALLATION  


PROCEDURE

Hide 64828 1.INSTALL BACK WINDOW GLASS CLIP LH

a.
B239018E01
0.059,0.058 0.305,0.216 0.246,0.158 10 *a 1.132,0.942 1.318,1.126 0.186,0.184 10 *b 3.125,0.72 3.311,0.903 0.186,0.184 10 *b 1.92,0.605 1.37,1.013 1.37,1.013 2.081,1.132 false 2.436,0.554 3.102,0.809 3.102,0.809 2.541,1.089 false

Apply Primer G to the glass where the clip will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from a new clip. Install a clip to the glass at the locations shown in the illustration.

Text in Illustration
*a Backside
*b Ceramic Notch


Hide 64827A 2.INSTALL BACK WINDOW GLASS CLIP RH

a.
B239017E01
0.062,0.059 0.252,0.226 0.191,0.166 10 *a 2.094,0.807 2.319,1.026 0.225,0.218 10 *b 0.221,0.751 0.446,0.970 0.225,0.218 10 *b 1.011,0.567 0.448,0.863 0.448,0.863 0.899,1.104 false 1.527,0.618 2.073,0.889 2.073,0.889 1.359,1.142 false

Apply Primer G to the glass where the clip will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from a new clip. Install a clip to the glass at the locations shown in the illustration.

Text in Illustration
*a Backside
*b Ceramic Notch


Hide 68294B 3.INSTALL BACK DOOR GLASS ADHESIVE DAM

B239019E01
0.054,0.048 0.280,0.292 0.225,0.244 10 *a 1.828,2.828 2.081,3.026 0.253,0.198 10 *b 2.65,1.094 2.903,1.291 0.253,0.198 10 *b 0.15,2.794 0.404,2.991 0.253,0.198 10 *b 1.407,2.775 1.81,2.917 1.81,2.917 1.407,3.067 false 0.736,2.779 0.371,2.889 0.371,2.889 0.736,3.067 false 2.169,0.689 2.719,1.074 2.719,1.074 2.831,0.685 false

a.

Apply Primer G to the glass where the dam will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from 2 new dams. Install the 2 dams to the glass at the locations shown in the illustration.

Text in Illustration
*a Backside
*b Ceramic Notch


Hide 75573C 4.INSTALL BACK WINDOW OUTSIDE MOULDING

B239020E02
0.073,0 0.323,0.271 0.25,0.271 10 false *a 0.302,0.708 0.458,0.917 0.156,0.208 10 false A 0.677,0.833 0.854,1.063 0.177,0.229 10 false A 2.885,1.229 3.042,1.438 0.156,0.208 10 false A 3.229,1.125 3.385,1.333 0.156,0.208 10 false A 1.01,1.792 1.417,2 0.406,0.208 10 false A - A 1.948,1.99 2.083,2.156 0.135,0.167 10 false a 0.792,3.052 1.01,3.26 0.219,0.208 10 false *1

a.

Using a brush or sponge, coat the application area of the back window glass outside moulding with Primer G.

Standard:
Area Specified Condition
a 13.0 mm (0.512 in.)


Text in Illustration
*1 Primer G
*a Backside


Hide 68131 5.INSTALL BACK DOOR GLASS

a.
B239016E01
0.297,0.558 0.572,0.838 false 0.068,0.426 0.249,0.621 0.181,0.195 10 *a

Position the glass.

i.

Using suction cups, place the glass in the correct position.


ii.

Check that the entire contact surface of the glass rim is perfectly even.


iii.

Place matchmarks on the glass and vehicle body on the locations indicated in the illustration.

HINT:
·

Placing matchmarks is only necessary when installing a new glass. When reusing the glass, matchmarks should already be present.

·

When reusing the glass, check and correct the matchmark positions.



NOTICE:

Check that the clips are attached to the vehicle body correctly.



iv.

Using suction cups, remove the glass.

Text in Illustration
*a Matchmark



b.
B239022E01
2.152,0.141 2.314,0.297 0.162,0.156 10 *a 1.684,0.565 1.875,0.706 0.191,0.140 10 *1 1.613,1.606 1.803,1.746 0.191,0.140 10 *1 0.966,4.287 1.157,4.428 0.191,0.140 10 *1 1.673,2.199 1.864,2.340 0.191,0.140 10 *2 2.247,2.308 2.437,2.448 0.191,0.140 10 *b 2.401,1.014 1.899,0.673 false 2.322,2.046 1.821,1.705 false 2.306,2.152 2.153,2.298 2.153,2.298 1.877,2.298 false

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.



Text in Illustration
*1 Primer M
*2 Adhesive
*a CORRECT
*b INCORRECT


c.

Using a brush or sponge, apply Primer G to the contact surface of the glass.

B239023E01
6.26,2.531 6.458,2.156 6.458,2.156 6.417,2.531 false 4.781,2.698 5.083,2.927 false 4.771,1.042 5.063,1.26 false 5.979,0.958 6.167,0.625 false 0.052,0 0.313,0.229 0.26,0.229 10 false *a 1.688,0.813 1.875,1.01 0.188,0.198 10 false A 1.688,1.198 1.875,1.396 0.188,0.198 10 false A 0.51,1.885 0.708,2.073 0.198,0.188 10 false B 0.094,1.792 0.292,1.979 0.198,0.188 10 false B 1.646,1.938 1.844,2.115 0.198,0.177 10 false D 1.656,2.323 1.854,2.5 0.198,0.177 10 false D 3.448,1.813 3.635,1.979 0.188,0.167 10 false C 3.823,1.729 4.01,1.896 0.188,0.167 10 false C 4.323,0.24 4.698,0.438 0.375,0.198 10 false A - A 5.604,0.24 5.979,0.438 0.375,0.198 10 false B - B 5.604,1.823 5.979,2.021 0.375,0.198 10 false C - C 4.323,1.823 4.698,2.021 0.375,0.198 10 false D - D 4.24,0.802 4.406,0.958 0.167,0.156 10 false a 4.469,1.281 4.615,1.427 0.146,0.146 10 false b 6.281,1.052 6.458,1.25 0.177,0.198 10 false b 5.875,1.521 6.052,1.719 0.177,0.198 10 false b 6.302,1.333 6.458,1.49 0.156,0.156 10 false c 4.292,2.583 4.427,2.771 0.135,0.188 10 false b 4.313,2.813 4.49,3.01 0.177,0.198 10 false e 5.875,2.979 6.052,3.146 0.177,0.167 10 false c 6.313,3.115 6.458,3.26 0.146,0.146 10 false d 6.729,2.74 6.938,2.906 0.208,0.167 10 false b 5.917,2.635 6.125,2.802 0.208,0.167 10 false b 0.698,3.521 0.969,3.75 0.271,0.229 10 false *1 6.188,0.479 6.396,0.688 0.208,0.208 10 false *b 5.104,1.229 5.313,1.438 0.208,0.208 10 false *b 5.094,2.906 5.302,3.115 0.208,0.208 10 false *b 6.417,1.958 6.625,2.167 0.208,0.208 10 false *b

Text in Illustration
*1 Primer G -
*a Backside *b Adhesive Center Line

Standard:
Area Specified Condition
a 13.0 mm (0.512 in.)
b 7.0 mm (0.276 in.)
c 37.6 mm (1.48 in.)
d 8.0 mm (0.315 in.)
e 13.4 mm (0.528 in.)


HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




d.

Apply adhesive to the back door glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass as shown in the illustration.

B239024E02
4.771,1.021 5.177,1.25 false 5.979,0.958 6.156,0.646 false 4.771,2.771 5.01,3 false 6.26,2.521 6.51,2.198 6.51,2.198 6.417,2.521 false 0.063,0.031 0.375,0.333 0.313,0.302 10 false *a 0.604,3.281 0.854,3.521 0.25,0.24 10 false a 1.042,2.802 1.24,3.01 0.198,0.208 10 false b 3.25,2.76 3.427,2.958 0.177,0.198 10 false b 2.771,2.688 2.99,2.875 0.219,0.188 10 false a 4.208,0.792 4.438,1.073 0.229,0.281 10 false c 6.292,1.323 6.458,1.5 0.167,0.177 10 false d 4.208,2.813 4.438,3.073 0.229,0.26 10 false e 5.885,3.01 6.115,3.25 0.229,0.24 10 false f 6.313,3.156 6.49,3.365 0.177,0.208 10 false b 1.802,0.354 1.969,0.563 0.167,0.208 10 false A 1.813,0.802 1.979,1.01 0.167,0.208 10 false A 0.104,1.448 0.26,1.646 0.156,0.198 10 false B 0.5,1.5 0.656,1.698 0.156,0.198 10 false B 1.677,1.563 1.833,1.76 0.156,0.198 10 false D 1.667,1.948 1.823,2.146 0.156,0.198 10 false D 3.438,1.438 3.646,1.615 0.208,0.177 10 false C 3.833,1.375 4.042,1.552 0.208,0.177 10 false C 4.24,0.281 4.615,0.469 0.375,0.188 10 false A - A 5.531,0.281 5.906,0.469 0.375,0.188 10 false B - B 4.24,1.969 4.615,2.156 0.375,0.188 10 false C - C 5.531,1.969 5.906,2.156 0.375,0.188 10 false D - D 6.51,2.031 6.677,2.198 0.167,0.167 10 false *b 5.052,2.979 5.219,3.146 0.167,0.167 10 false *b 5.208,1.208 5.448,1.365 0.24,0.156 10 false *b 6.177,0.469 6.344,0.635 0.167,0.167 10 false *b 1.479,3.344 2.125,3.615 0.646,0.271 10 false *1

Text in Illustration
*1 Adhesive - -
*a Backside *b Adhesive Center Line

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)
c 13.0 mm (0.512 in.)
d 37.6 mm (1.48 in.)
e 13.4 mm (0.528 in.)
f 7.0 mm (0.276 in.)




e.

Install the back door glass to the vehicle body.

i.

Hold the back window glass securely in place with tape or equivalent until the adhesive has hardened.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




ii.

Lightly press the front surface of the back window glass to ensure that the back window glass is securely installed to the vehicle body.


iii.

Using a scraper, remove any excess or protruding adhesive.

HINT:

Apply adhesive to any areas where the amount of adhesive is inadequate.


NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



iv.

Connect the connectors.



Hide 68131 6.CHECK FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 75573H 7.INSTALL BACK WINDOW UPPER OUTSIDE MOULDING

a.

Apply Primer G to the glass where the moulding will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from 2 new upper outside mouldings. Install the 2 moulding to the glass at the locations shown in the illustration.

B239025E02
4.094,1.01 4.01,1.031 4.01,1.031 4.01,1.219 false 3.073,0.917 3.156,0.948 3.156,0.948 3.156,1.177 false 2.365,1.792 2.531,1.99 0.167,0.198 10 true A 2.302,2.219 2.469,2.417 0.167,0.198 10 true A 4.073,1.865 4.24,2.063 0.167,0.198 10 true A 4.135,2.292 4.302,2.49 0.167,0.198 10 false A 0.51,1.781 0.917,2.01 0.406,0.229 10 false A - A 1.073,0.427 1.365,0.667 0.292,0.24 10 false *1 3.938,0.427 4.167,0.667 0.229,0.24 10 false *2 3.073,1.208 3.333,1.417 0.26,0.208 10 false *a 3.927,1.229 4.188,1.438 0.26,0.208 10 false *a

Text in Illustration
*1 Back Window Upper Outside Moulding LH *2 Back Window Upper Outside Moulding RH
*a Ceramic Notch - -


Hide 67381A 8.INSTALL NO. 1 BACK WINDOW WIPER MOTOR BRACKET

Hide 85110R 9.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 76085 11.INSTALL REAR SPOILER SUB-ASSEMBLY

Hide 69205F 13.INSTALL BACK DOOR INSIDE HANDLE SUB-ASSEMBLY (for Face to Face Seat Type)

Hide 64780A 14.INSTALL BACK DOOR TRIM PANEL ASSEMBLY

Hide 69783B 15.INSTALL BACK DOOR INSIDE HANDLE BEZEL (for Face to Face Seat Type)

Hide 75202B 17.INSTALL UPPER TOOL BOX PANEL SUB-ASSEMBLY

Hide 67761A 18.INSTALL BACK DOOR TRIM COVER

Hide 67938A 19.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 20.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 21.INSTALL BACK DOOR CENTER GARNISH

Hide 64773A 22.INSTALL NO. 2 SPARE WHEEL COVER

Hide 23.INSTALL SPARE TIRE

Hide 64771 24.INSTALL SPARE WHEEL COVER

Hide 64772B 25.INSTALL SPARE WHEEL COVER PAD