Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.

If power window initialization has not been performed, the auto up and down function will not operate (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

WIRING DIAGRAM

B449854E03
1.333,0.75 4.833,1 3.5,0.25 10 false Main Body ECU (Multiplex Network Body ECU) 1.917,2.583 3.833,3 1.917,0.417 10 false Rear Power Window Regulator Switch Assembly RH 1.917,2.385 2.854,2.583 0.938,0.198 10 false L2 5,2.667 6.948,3.083 1.948,0.417 10 false Rear Power Window Regulator Motor Assembly RH 5,2.469 5.615,2.667 0.615,0.198 10 false L4 0.781,4.354 2.615,4.604 1.833,0.25 10 false : LIN Communication Line 2.969,1.969 3.583,2.167 0.615,0.198 10 false AUTO 5.385,1.969 6,2.167 0.615,0.198 10 false AUTO 2.042,1.969 2.5,2.167 0.458,0.198 10 false GND 5.104,1.844 5.26,2.042 0.156,0.198 10 false 4 3.479,1.844 3.635,2.042 0.156,0.198 10 false 8 1.802,1.844 1.958,2.042 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

If the rear power window regulator motor assembly RH has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Check that the "RR Window Auto Up" and "RR Window Auto Down" power window control system customize settings are "ON" before proceeding with work (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS).

·

After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally.



HINT:

If the pulse sensor built into the rear power window regulator motor assembly RH is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for Rear Door RH) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for Rear Door RH) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>FAIL-SAFE CHART).


PROCEDURE

1.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal / OFF or ON OFF: Rear RH door power window auto switch not being operated
ON: Rear RH door power window auto switch being operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

2.PERFORM INITIALIZATION (FOR REAR RH DOOR)

NG

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR)
2.PERFORM INITIALIZATION (FOR REAR RH DOOR)
a.

Initialize the rear power window regulator motor assembly RH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



NEXT

3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
3.CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)
a.

Check that the rear RH door power window moves when the auto up and down function of the rear power window regulator switch assembly (for Rear RH Door) is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).



OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR)
a.

Remove the rear power window regulator switch assembly (for Rear RH Door) (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Inspect the rear power window regulator switch assembly (for Rear RH Door) (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR REAR RH DOOR) - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the L2 rear power window regulator switch assembly (for Rear RH) connector.


b.

Disconnect the L4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-8 (AUTO) - L4-4 (AUTO) Always Below 1 Ω
L2-1 (GND) - Body ground Always Below 1 Ω
L2-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR