Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261239 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 28800 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 53828J 3.REMOVE FRONT FENDER SIDE PANEL PROTECTOR LH

Hide 53827K 4.REMOVE FRONT FENDER SIDE PANEL PROTECTOR RH

Hide 53867H 5.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 85192 7.REMOVE WINDSHIELD WIPER ARM COVER

Hide 85221B 8.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85211B 9.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55781E 10.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 75536B 11.REMOVE WINDSHIELD LOWER OUTSIDE MOULDING LH

a.
B241712

Remove the windshield lower outside moulding.

i.

Put protective tape around the moulding.


ii.

Using a moulding remover, detach the 5 clips and remove the moulding.

NOTICE:
·

When removing the windshield lower outside moulding, be careful not to damage the roof drip side finish moulding clip.

·

If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.





Hide 75535A 12.REMOVE WINDSHIELD LOWER OUTSIDE MOULDING RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 17.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 18.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 74616C 19.REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

Hide 74615E 20.REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

Hide 89943 30.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 89941 31.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 87810 32.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87834 33.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 87810 34.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 63310 35.REMOVE ROOF HEADLINING ASSEMBLY

a.

w/ Sliding Roof:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 5 Door)>REMOVAL).




b.

w/o Sliding Roof:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (for 3 Door)>REMOVAL).




Hide 56111 36.REMOVE WINDSHIELD GLASS

NOTICE:
·

There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle specifications, a 1-piece or 2-piece type stopper is used.


B238992E05
1.646,0.927 1.427,0.865 false 5.177,0.792 4.99,0.792 false 5.458,0.677 5.625,0.927 5.625,0.927 5.729,0.927 false 1.781,0.25 2,0.5 0.219,0.25 10 false *A 5.479,0.25 5.698,0.5 0.219,0.25 10 false *B 1.26,0.771 1.49,0.99 0.229,0.219 10 false *1 4.833,0.719 5.063,0.938 0.229,0.219 10 false *1 5.76,0.854 5.99,1.073 0.229,0.219 10 false *2

Text in Illustration
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper

a.

w/ Windshield Deicer System:

Disconnect the windshield deicer connector.


b.
B238993E01
0.451,0.208 0.671,0.419 0.221,0.211 10 *1 1.274,0.543 0.686,0.288 false

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

Text in Illustration
*1 Protective Tape


c.
B238994E04
1.26,3.271 0.948,3.271 false 1.271,2.917 1.271,2.427 1.271,2.427 2.5,2.427 false 2.26,2.906 2.26,2.427 false 2.448,1.073 2.865,1.281 2.865,1.281 2.865,1.417 false 0.49,1.583 0.49,1.208 0.49,1.208 0.333,1.208 false 1.677,0.75 1.49,0.219 1.49,0.219 1.375,0.219 false 1.25,0.781 1.031,0.365 1.031,0.365 0.927,0.365 false 0.74,0.281 0.906,0.458 0.167,0.177 10 false *1 1.188,0.146 1.427,0.396 0.24,0.25 10 false *2 0.146,1.073 0.375,1.271 0.229,0.198 10 false *3 2.75,1.469 2.958,1.646 0.208,0.177 10 false *4 2.552,2.365 2.75,2.542 0.198,0.177 10 false *5 1.281,3.177 1.51,3.375 0.229,0.198 10 false *2

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


d.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.



Text in Illustration
*1 Plastic Sheet
*2 Piano Wire
*3 Wooden Blocks
*4 Protective Tape
*5 Stopper


e.
B238990E03
1.646,0.927 1.417,0.927 1.417,0.927 1.417,1.885 false 1.333,1.917 1.594,2.146 0.26,0.229 10 false *a

Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

NOTICE:

Matchmarks do not need to be placed if not reusing the glass.


Text in Illustration
*a Matchmark


f.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the glass.



g.

Disconnect the stoppers.


h.
B238991

Using suction cups, remove the glass.


Hide 56117D 37.REMOVE WINDSHIELD GLASS ADHESIVE DAM

a.

Using a scraper, remove the adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the adhesive dam with a new one.




Hide 75533G 38.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

Using a scraper, remove the moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the moulding with a new one.




Hide 56116C 39.REMOVE NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a scraper, remove the 2 stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the stoppers with new ones.




Hide 56115A 40.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B238995

Remove the 2 No. 1 stoppers.

NOTICE:

Be sure to replace the No. 1 stoppers with new ones.



Hide 75545B 41.REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

B241713

a.

Remove the 5 No. 1 windshield moulding clips.

HINT:

Use the same procedure to remove the 5 clips on the other side.



Hide 75547B 42.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clips.


a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.
B238988E03
1.427,1.698 1.854,1.896 0.427,0.198 10 false 5 mm

Lightly press the drill against the No. 3 windshield outside moulding clips, drill off the flanges of the No. 3 windshield outside moulding clips, and remove it.

NOTICE:
·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Do not pry the No. 3 windshield outside moulding clips with the drill because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.



CAUTION:

Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.



d.

Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

HINT:

Use the same procedure to remove clips on the other side.



Hide 56111 43.CLEAN WINDSHIELD GLASS

B106929

a.

Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.


b.

Clean the outer circumference of the glass with non-residue solvent.

NOTICE:
·

Do not touch the surface of the glass after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 44.CLEAN VEHICLE BODY

B106081E39
0.49,1.344 0.771,0.771 0.771,0.771 0.948,0.771 false 2.281,1.458 2.563,0.76 2.563,0.76 2.729,0.76 false 2.417,1.594 2.417,1.771 false 0.813,1.563 0.813,1.75 false 0.979,0.677 1.219,0.875 0.24,0.198 10 false *1 2.781,0.677 3.021,0.875 0.24,0.198 10 false *1 0.74,1.771 0.979,1.969 0.24,0.198 10 false *2 2.354,1.823 2.594,2.021 0.24,0.198 10 false *2

a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.


Text in Illustration
*1 Adhesive
*2 Vehicle Body