The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1579 | Telephone microphone signal is lost. | ·
Radio and display receiver assembly ·
Map light assembly ·
Telephone microphone assembly ·
Telematics transceiver* ·
Harness or connector |
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| w/o Telematics Transceiver | A |
| w/ Telematics Transceiver | B |
A
B
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the W7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-4 (MACC) - W7-11 (MACC) | Always | Below 1 Ω |
| H51-5 (MIN+) - W7-12 (MCO+) | Always | Below 1 Ω |
| H51-19 (MIN-) - W7-13 (MCO-) | Always | Below 1 Ω |
| H51-6 (SNS2) - W7-14 (SNS2) | Always | Below 1 Ω |
| H51-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| H51-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| H51-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| H51-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| H51-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-11 (MACC) - B-5 (MACC) | Always | Below 1 Ω |
| A-12 (MCO+) - B-3 (MIC+) | Always | Below 1 Ω |
| A-13 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| A-14 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| A-11 (MACC) - A-12 (MCO+) | Always | 10 kΩ or higher |
| A-11 (MACC) - A-13 (MCO-) | Always | 10 kΩ or higher |
| A-11 (MACC) - A-14 (SNS2) | Always | 10 kΩ or higher |
| A-12 (MCO+) - A-13 (MCO-) | Always | 10 kΩ or higher |
| A-12 (MCO+) - A-14 (SNS2) | Always | 10 kΩ or higher |
| A-13 (MCO-) - A-14 (SNS2) | Always | 10 kΩ or higher |
OK
NG
Replace the telephone microphone assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).
Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the W7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-6 (SNS2) - W7-14 (SNS2) | Always | Below 1 Ω |
OK
NG
Disconnect the H51 radio and display receiver assembly connector.
Disconnect the G187 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H51-5 (MIN+) - G187-18 (MCO+) | Always | Below 1 Ω |
| H51-19 (MIN-) - G187-19 (MCO-) | Always | Below 1 Ω |
| H51-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| H51-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| H51-18 (SGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the G187 telematics transceiver connector.
Disconnect the W7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G187-33 (MCVD) - W7-11 (MACC) | Always | Below 1 Ω |
| G187-34 (MCI+) - W7-12 (MCO+) | Always | Below 1 Ω |
| G187-35 (MCI-) - W7-13 (MCO-) | Always | Below 1 Ω |
| G187-33 (MCVD) - Body ground | Always | 10 kΩ or higher |
| G187-34 (MCI+) - Body ground | Always | 10 kΩ or higher |
| G187-35 (MCI-) - Body ground | Always | 10 kΩ or higher |
| G187-32 (SGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-11 (MACC) - B-5 (MACC) | Always | Below 1 Ω |
| A-12 (MCO+) - B-3 (MIC+) | Always | Below 1 Ω |
| A-13 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| A-14 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| A-11 (MACC) - A-12 (MCO+) | Always | 10 kΩ or higher |
| A-11 (MACC) - A-13 (MCO-) | Always | 10 kΩ or higher |
| A-11 (MACC) - A-14 (SNS2) | Always | 10 kΩ or higher |
| A-12 (MCO+) - A-13 (MCO-) | Always | 10 kΩ or higher |
| A-12 (MCO+) - A-14 (SNS2) | Always | 10 kΩ or higher |
| A-13 (MCO-) - A-14 (SNS2) | Always | 10 kΩ or higher |
OK
NG
| *a | Component with harness connected
(Telematics Transceiver) |
Disconnect the W7 map light assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G187-33 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G187-32 (SGND) - Body ground | Always | Below 1 Ω |
| G187-35 (MCI-) - Body ground | Always | Below 1 Ω |
OK
NG
Replace the telephone microphone assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL
Check for DTCs.
No DTCs are output.
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)