Home › Engine / Hybrid System › 5L-E (FUEL) › FUEL TANK › 2016.08–2020.08
RM27T0E _51 Engine / Hybrid System _053668 5L-E FUEL _0260555 FUEL TANK A

5L-E FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A220824E01
0.432,2.664 0.621,2.811 0.189,0.147 10 *1 0.645,2.752 0.744,2.752 0.744,2.752 1.376,3.438 false 2.247,2.798 2.436,2.945 0.189,0.147 10 *2 2.209,2.887 2.11,2.887 2.11,2.887 1.527,3.573 false

Align the fuel tank side mark with the hose side mark.

Text in Illustration
*1 Fuel Tank Side Mark
*2 Hose Side Mark


b.

Install the fuel tank to filler pipe hose to the fuel tank.


Hide 77643A 2.INSTALL NO. 3 FUEL TANK PROTECTOR

a.

Install the No. 3 fuel tank protector and attach the 4 clamps.


b.

Install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 77010 3.INSTALL FUEL TANK VENT TUBE ASSEMBLY

a.
A387302C02
0.948,1.5 0.948,0.896 true 0.948,1.333 1.292,1.333 1.292,1.333 1.292,1.021 true 0.865,1.51 1.177,1.667 0.313,0.156 10 false *a
*a Co-rotation Prevention Check Mark


Apply a co-rotation prevention check mark to the fuel tank vent tube assembly.

HINT:

Perform this procedure when replacement of the fuel tank vent tube assembly is necessary.



b.

Apply a light coat of diesel fuel or grease to a new gasket and install the gasket to the fuel tank sub-assembly.


c.
A220825C06
1.156,2.781 1.365,2.333 1.365,2.333 1.51,2.333 true 1.198,2.979 1.594,2.979 true 1.604,2.24 1.802,2.417 0.198,0.177 10 false *a 1.635,2.896 1.854,3.063 0.219,0.167 10 true *b
*a Protrusion
*b Groove


Set the fuel tank vent tube assembly to the fuel tank sub-assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.


HINT:

Align the cutout of the fuel tank vent tube assembly to the groove of the fuel tank sub-assembly.



d.
A387315C02
1.771,1.021 1.958,1.021 1.958,1.021 2.198,0.927 true 2.396,0.906 2.552,0.74 2.552,0.74 2.729,0.74 false 2.75,0.656 3.063,0.875 0.313,0.219 10 true *a 1.615,0.938 1.927,1.094 0.313,0.156 10 false *b
*a Rotational Start Point Mark (Fuel Tank Sub-assembly Side)
*b Rotational Start Point Mark (Fuel Pump Gauge Retainer Side)


Temporarily place the fuel pump gauge retainer by aligning the rotational start point mark of a new fuel pump gauge retainer with the rotational start point mark of the fuel tank sub-assembly while pressing the fuel tank vent tube assembly into the fuel tank sub-assembly.


e.
A393131C01
0.719,4.396 1.646,4.135 true 1.208,2.469 1.625,2.74 true 1.667,2.854 2.469,2.583 true 1.063,1.146 1.458,1.281 true 0.615,0.635 0.865,0.802 true 0.792,2.802 0.594,2.292 true 1.5,1.24 1.813,1.396 0.313,0.156 10 false *1 0.458,0.5 0.771,0.656 0.313,0.156 10 false *a 2.479,2.458 2.792,2.615 0.313,0.156 10 false *b 1.073,2.323 1.385,2.479 0.313,0.156 10 false *c 0.552,4.333 0.865,4.49 0.313,0.156 10 false *d 0.49,2.125 0.802,2.281 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Rib
*c Cutout
*d SST (Claw Set) Incorrect Installation Point (Rotational Start Point Mark of Fuel Pump Gauge Retainer)


Set 4 SSTs (claw sets) to the fuel pump gauge retainer and temporarily install.

SST
09808-14031  (09808-01080, 09808-01090, 09808-01100)

NOTICE:
·

Align the cutout of SST (claw set) to the rib of the fuel pump gauge retainer.

·

Do not place SST on the rotational start point mark of the fuel pump gauge retainer, otherwise SST (claw set) cannot be set correctly.




f.
A387296C03
2.333,1.313 2.51,1.104 2.51,1.104 2.698,1.104 false 1.146,0.74 1.344,0.74 1.344,0.74 1.75,1.052 false 1.115,2.063 1.313,2.063 1.313,2.063 1.563,1.833 false 2.74,1.021 3.052,1.177 0.313,0.156 10 false *1 0.958,0.667 1.271,0.823 0.313,0.156 10 false *a 0.948,1.979 1.26,2.135 0.313,0.156 10 false *b
*1 Fuel Pump Gauge Retainer
*a SST (Claw Set)
*b Hook
V100135

Press
V100136

SST (Bolt)


While firmly pressing the claw of SST (claw set) into rib of the fuel pump gauge retainer, tighten the bolt.


g.
A387297C03
0.615,0.438 1.052,0.438 false 0.875,1.906 1.063,1.906 1.063,1.906 1.219,1.563 true 0.448,0.354 0.76,0.51 0.313,0.156 10 false *a 0.698,1.833 1.01,1.99 0.313,0.156 10 false *b
*a SST (Plate)
*b SST (Claw Set)
V100135

SST (Bolt)


Temporarily install SST (plate) to SST (claw set) with 4 SSTs (bolts).


h.
A387317C03
0.615,1.198 0.854,1.198 0.854,1.198 1.333,0.906 true 1.74,1.083 2.573,1.083 true 2.604,1 2.917,1.198 0.313,0.198 10 true *a 0.427,1.094 0.74,1.25 0.313,0.156 10 false *b
*a Center of Fuel Pump Gauge Retainer
*b SST (Plate)


Adjust the position of SST (plate) so that the setting hole of SST (handle) aligns with the center of the fuel pump gauge retainer.


i.
A393430C01
0.844,3.792 0.74,3.354 true 2.26,3.177 1.875,3.385 true 2.531,3.583 1.719,4.021 true 1.333,1.323 0.469,1.063 true 1.531,0.365 1.615,0.688 true 0.635,3.167 0.948,3.323 0.313,0.156 10 false *1 1.417,0.177 1.729,0.333 0.313,0.156 10 false *a 2.281,3.063 2.594,3.219 0.313,0.156 10 false *b 0.292,0.948 0.604,1.104 0.313,0.156 10 false *c 2.552,3.438 2.865,3.594 0.313,0.156 10 false *d
*1 Fuel Pump Gauge Retainer
*a SST (Plate)
*b SST (Claw Set)
*c SST (Bolt)
*d Rib
V113147

Press


While firmly pressing the SST (claw set) into rib of the fuel pump gauge retainer, tighten SST (bolt).


j.
A387316C02
0.938,0.594 1.354,0.594 1.354,0.594 1.354,0.99 true 1.073,0.917 1.073,0.594 false 0.667,0.521 0.927,0.698 0.26,0.177 10 true *a 2.781,1.042 3.094,1.198 0.313,0.156 10 true *b 0.542,1.042 0.854,1.198 0.313,0.156 10 false *c
*a Co-rotation Prevention Check Mark
*b Tightening Start Position
*c One and Half Rotation Position


While one person presses the fuel tank vent tube assembly into the fuel tank sub-assembly, have another person firmly press the fuel pump gauge retainer into the threads of the fuel tank sub-assembly and tighten approximately one and a half turns.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel tank vent tube assembly will place excessive force on the pump gauge retainer and be difficult to remove, and parts may be damaged.

·

Do not use an impact wrench or turn the SST handle with excessive force, as parts may be damaged.

·

Do not rotate the fuel pump gauge retainer when the co-rotation prevention check mark is out of place.




k.
A387304C02
0.969,2.083 0.969,1.865 0.969,1.865 1.344,1.573 true 0.885,2.083 1.198,2.24 0.313,0.156 10 false *a 2.708,1.906 3.021,2.063 0.313,0.156 10 false *b 2.583,0.115 2.896,0.271 0.313,0.156 10 false *c 1.635,2.542 1.948,2.698 0.313,0.156 10 true *d
*a SST (Plate)
*b Person in Charge of Tightening
*c Person in Charge of Supporting
*d Approximately 180°


While one person presses the fuel tank vent tube assembly into the fuel tank sub-assembly, have another person slowly tighten approximately 180°.


l.

Check the tightening condition of the fuel pump gauge retainer.

i.
A387306C02
1.948,1.885 2.052,2.094 2.052,2.094 2.229,2.094 false 0.438,2.875 0.75,2.875 false 0.75,3.865 0.948,3.865 0.948,3.865 1.354,3.469 false 0.708,1.438 0.885,1.438 0.885,1.438 1.083,1.313 false 2.125,0.844 2.323,0.875 2.323,0.875 2.458,0.875 false 1.99,2.813 2.323,2.583 2.323,2.583 2.5,2.583 false 0.24,2.813 0.552,2.969 0.313,0.156 10 false *1 0.563,3.792 0.875,3.948 0.313,0.156 10 false *2 2.208,3.427 2.521,3.583 0.313,0.156 10 false *c 2.25,2 2.563,2.156 0.313,0.156 10 false *b 0.552,1.344 0.865,1.5 0.313,0.156 10 false *b 2.49,0.781 2.802,0.938 0.313,0.156 10 true *b 2.521,2.479 2.833,2.635 0.313,0.156 10 false *a
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Sub-assembly
*a Vernier Caliper
*b Measurement Position
*c Measurement Height


Using a vernier caliper, measure the upper surface dimensions of the fuel tank assembly at the 3 positions as shown in the illustration.

Standard:

Measurement difference is within 3 mm.


NOTICE:

If the measurement difference is approximately 6 mm, the threads misaligned by 1 threads (6 mm) and the fuel pump gauge retainer must be installed again.




m.
A387305C02
2.417,2.698 2.635,2.552 2.635,2.552 2.844,2.552 true 0.76,1.615 0.76,1.417 0.76,1.417 1.021,1.042 true 0.615,0.135 0.823,0.135 0.823,0.135 0.948,0.563 true 1.635,3.073 1.792,3.073 1.792,3.073 2.115,2.979 true 0.438,0.031 0.75,0.188 0.313,0.156 10 false *a 0.667,1.646 0.979,1.802 0.313,0.156 10 false *b 1.427,2.99 1.74,3.146 0.313,0.156 10 false *d 2.792,3.438 3.104,3.594 0.313,0.156 10 false *c 2.896,2.438 3.208,2.594 0.313,0.156 10 false *e 3.01,1.365 3.323,1.521 0.313,0.156 10 false *f 2.323,0.094 2.635,0.25 0.313,0.156 10 false *g
*a SST (Handle)
*b SST (Plate)
*c Tightening Complete Position
*d Rotational Start Point Mark of Fuel Pump Gauge Retainer
*e Rotational Start Point Mark of Fuel Tank Assembly
*f Person in Charge of Tightening
*g Person in Charge of Supporting
V100135

Tighten


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010, 09808-01020)


n.

While one person presses the fuel tank vent tube assembly onto the fuel tank sub-assembly, have another person use SST (handle) and slowly tighten the fuel pump gauge retainer until it reaches the tightening complete position.


Hide 77209D 4.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A223113

Install the fuel tank main tube and fuel return tube with the 2 fuel tube joint clips.

NOTICE:
·
A118171E07
2.57,0.9 2.764,1.046 0.194,0.146 10 *4 2.543,0.989 1.629,0.989 false 0.231,0.553 0.425,0.699 0.194,0.146 10 *1 0.973,0.633 0.448,0.633 false 0.037,1.255 0.230,1.401 0.194,0.146 10 *2 0.973,1.335 0.253,1.335 false 0.973,1.179 0.359,1.179 0.359,1.179 0.359,1.334 false 1.971,0.033 2.165,0.179 0.194,0.146 10 *3 1.949,0.123 1.866,0.123 1.866,0.123 1.703,0.496 false 0.884,4.269 1.078,4.415 0.194,0.146 10 *a 2.56,4.269 2.754,4.415 0.194,0.146 10 *b

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the fuel tube joint clips are on the collars of the fuel tube joints.

·

After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.

Text in Illustration
*1 Fuel Tube Joint
*2 O-Ring
*3 Fuel Tube
*4 Fuel Tube Joint Clip
*a CORRECT
*b INCORRECT




b.

Install the fuel tank main tube and fuel return tube to the fuel tank.


Hide 77209D 5.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL RETURN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A223114

Install the fuel tank main tube and fuel return tube with the 2 fuel tube joint clips.

NOTICE:
·
A118171E07
2.57,0.9 2.764,1.046 0.194,0.146 10 *4 2.543,0.989 1.629,0.989 false 0.231,0.553 0.425,0.699 0.194,0.146 10 *1 0.973,0.633 0.448,0.633 false 0.037,1.255 0.230,1.401 0.194,0.146 10 *2 0.973,1.335 0.253,1.335 false 0.973,1.179 0.359,1.179 0.359,1.179 0.359,1.334 false 1.971,0.033 2.165,0.179 0.194,0.146 10 *3 1.949,0.123 1.866,0.123 1.866,0.123 1.703,0.496 false 0.884,4.269 1.078,4.415 0.194,0.146 10 *a 2.56,4.269 2.754,4.415 0.194,0.146 10 *b

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the fuel tube joint clips are on the collars of the fuel tube joints.

·

After installing the fuel tube joint clips, check that the fuel tube joints cannot be pulled off.

Text in Illustration
*1 Fuel Tube Joint
*2 O-Ring
*3 Fuel Tube
*4 Fuel Tube Joint Clip
*a CORRECT
*b INCORRECT




b.

Install the fuel tank main tube to the fuel tank.


c.

Install the fuel return tube to the fuel tank and attach the clamp.


Hide 77651A 6.INSTALL FUEL TANK CUSHION

a.

Install 3 new fuel tank cushions to the fuel tank.


Hide 77100U 7.INSTALL FUEL TANK SUB-ASSEMBLY

a.

Set the fuel tank on a transmission jack and rise the transmission jack.

NOTICE:

Do not allow the fuel tank to contact the vehicle, especially the differential.



b.

Install the 2 fuel tank bands with the 2 pins and 2 clips.


c.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 77213B 8.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the filler pipe.


Hide 77012 9.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Single Tank Type)

a.

Connect the fuel tank breather tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 10.CONNECT FUEL CUT OFF TUBE (for Single Tank Type)

Hide 77012 11.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Connect the fuel tank breather tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77207A 12.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.

Connect the fuel return tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 13.CONNECT FUEL CUT OFF TUBE (for Double Tank Type)

a.

Connect the fuel cut off tube (See page Engine / Hybrid System>5L-E (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77207A 14.CONNECT FUEL RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

Hide 77209D 15.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

Hide 77209D 16.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

Hide 77606 17.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector with the 6 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 58325E 18.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel sender gauge connector.


b.

Install the rear floor service hole cover with the 3 screws.


Hide 67918D 19.INSTALL REAR DOOR SCUFF PLATE LH

Hide 67934 20.INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

Hide 58371F 21.INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

Hide 22.INSTALL REAR SEAT ASSEMBLY LH

a.

for 60/40 Split Double-folding Seat Type LH Side:

Install the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>INSTALLATION).


b.

for 60/40 Split Slide Walk-in Seat Type LH Side:

Install the rear seat assembly LH (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)>INSTALLATION).


Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).