The injector driver delivers drive signals to the injector assemblies using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the injector driver receives a fuel injection command (#1 to #4) signal from the ECM, the injector driver responds to the command with an injector injection confirmation (INJF) signal when the current is applied to the injector assembly.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Idling for 5 seconds | Open or short in the injector driver or fuel injector circuit (1 trip detection logic). | ·
Open or short in injector driver circuit ·
Injector assembly ·
Injector driver ·
ECM |
The ECM continuously monitors both injection command (#1 to #4) signals and injection confirmation (INJF) signals. This DTC will be stored if the ECM determines that the number of #1 to #4 signals is inconsistent with the number of INJF signals.
The injector assemblies are grounded through a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector assembly current becomes too high, the voltage drop over the resistor exceeds a specified level and no IJF signal for that cylinder is sent to the ECM.
After the engine is started, when there is no injection confirmation (INJF) signal sent from the injector driver to the ECM even though the ECM sends injection command (#1 to #4) signals to the injector driver, DTC P062D is stored.
If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The ECM continues operating in fail-safe mode until the ignition switch is turned off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
When DTC P0200 is stored, the malfunctioning parts can be narrowed down according to fail-safe behavior.
When a DTC is stored but the engine does not stall, there may be an open circuit or malfunction in the following components which affect the control of individual cylinders.
The circuit inside an injector assembly.
The wiring between an injector driver and injector assembly (between terminal IJ1+ and the No. 1 injector assembly, terminal IJ1 and the No. 1 injector assembly, etc.).
The wiring between an injector driver and the ECM (terminals #10 and #1, etc.).
When a DTC is stored and the engine stalls, there may be a malfunction in the wiring which affects the control of multiple cylinders.
Wiring between an injector driver and the ECM (between INJF terminals).
The power supply wiring.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the injector driver connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C88-2 (+B) - C88-3 (GND) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to injector driver) |
Reconnect the injector driver connectors.
OK
NG
Inspect the injector assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
Disconnect the injector assembly connectors.
Disconnect the injector driver connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-1 - C88-1 (IJ1+) | Always | Below 1 Ω |
| C1-2 - C99-6 (IJ1-) | Always | Below 1 Ω |
| C2-1 - C88-6 (IJ2+) | Always | Below 1 Ω |
| C2-2 - C88-4 (IJ2-) | Always | Below 1 Ω |
| C3-1 - C99-5 (IJ3+) | Always | Below 1 Ω |
| C3-2 - C99-2 (IJ3-) | Always | Below 1 Ω |
| C4-1 - C99-3 (IJ4+) | Always | Below 1 Ω |
| C4-2 - C99-5 (IJ4-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C1-1 or C88-1 (IJ1+) - Body ground | Always | 10 kΩ or higher |
| C1-2 or C99-6 (IJ1-) - Body ground | Always | 10 kΩ or higher |
| C2-1 or C88-6 (IJ2+) - Body ground | Always | 10 kΩ or higher |
| C2-2 or C99-4 (IJ2-) - Body ground | Always | 10 kΩ or higher |
| C3-1 or C88-5 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| C3-2 or C99-2 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| C4-1 or C99-3 (IJ4+) - Body ground | Always | 10 kΩ or higher |
| C4-2 or C99-5 (IJ4-) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector assembly connectors.
Reconnect the injector driver connectors.
OK
NG
Disconnect the injector driver connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C89-4 (#10) - C90-21 (#1) | Always | Below 1 Ω |
| C89-8 (#20) - C90-22 (#2) | Always | Below 1 Ω |
| C89-7 (#30) - C90-23 (#3) | Always | Below 1 Ω |
| C89-3 (#40) - C90-24 (#4) | Always | Below 1 Ω |
| C89-5 (INJF) - C90-20 (INJF) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C89-4 (#10) or C90-21 (#1) - Body ground | Always | 10 kΩ or higher |
| C89-8 (#20) or C90-22 (#2) - Body ground | Always | 10 kΩ or higher |
| C89-7 (#30) or C90-23 (#3) - Body ground | Always | 10 kΩ or higher |
| C89-3 (#40) or C90-24 (#4) - Body ground | Always | 10 kΩ or higher |
| C89-5 (INJF) or C90-20 (INJF) - Body ground | Always | 10 kΩ or higher |
Reconnect the injector driver connector.
Reconnect the ECM connector.
OK
NG
Replace the injector driver (See page Engine / Hybrid System>1KD-FTV (FUEL)>INJECTOR DRIVER>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0200 is output | A |
| No output | B |
A
B
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Go to the injector circuit (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>Injector Circuit).
NEXT
Replace the injector assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
NEXT
Register the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Perform the injector pilot quantity learning (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 10 seconds.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
NEXT