Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM J

1KD-FTV ENGINE CONTROL  ECD SYSTEM  Injector Circuit  


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK INJECTOR DRIVER (POWER SOURCE)
a.
U169188E01
0.546,1.307 0.827,1.459 0.281,0.152 10 C88 0.626,0.765 1.101,0.912 0.476,0.147 10 +B (+) 1.7,1.206 1.173,0.859 false 0.074,0.119 0.273,0.271 0.199,0.152 10 *a 2.456,1.662 3.024,1.809 0.568,0.147 10 GND (-) 2.443,1.647 1.989,1.258 false

Disconnect the injector driver connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C88-2 (+B) - C88-3 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Injector Driver)


c.

Reconnect the injector driver connector.



OK

NG

2.INSPECT NO. 1 INTEGRATION RELAY (EDU)
2.INSPECT NO. 1 INTEGRATION RELAY (EDU)
a.

Inspect the No. 1 integration relay (EDU) (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EDU) - INJECTOR DRIVER)

NG

REPLACE NO. 1 INTEGRATION RELAY (EDU)

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EDU) - INJECTOR DRIVER)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the injector driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C88-2 (+B) - 1B-8 Always Below 1 Ω
C88-3 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C88-2 (+B) or 1U-2 - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 1 injector driver connector.


e.

Reinstall the integration relay.



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G58-12 (IREL) - 1U-1 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G58-12 (IREL) or 1U-1 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reinstall the No. 1 integration relay.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR