Home › Engine / Hybrid System › 1KD-FTV (FUEL) › FUEL INJECTOR › 2015.06–2020.08
RM27T0E _51 Engine / Hybrid System _053669 1KD-FTV FUEL _0260567 FUEL INJECTOR A

1KD-FTV FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 25800 2.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)

a.

Remove the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).


Hide 87245A 3.DISCONNECT INLET HEATER WATER HOSE (w/o EGR System)

Hide 25709E 4.DISCONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o EGR System)

Hide 17113E 5.REMOVE NO. 1 INTAKE PIPE (w/o EGR System)

Hide 22267A 6.REMOVE THROTTLE BODY BRACKET (w/o EGR System)

Hide 23701 7.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR System)

NOTICE:
·

After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.

·

After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



a.
A223285

Remove the 2 nuts and No. 3 injection pipe clamp.


b.
A223286

Remove the 2 bolts and 2 No. 2 injection pipe clamps.


c.
A223287E02
0.083,0.083 0.375,0.365 0.292,0.281 10 true *a 0.073,2.708 0.365,2.958 0.292,0.25 10 true *b

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.

Text in Illustration
*a Injector Side
*b Common Rail Side


Hide 17871A 8.REMOVE AIR CONNECTOR STAY (w/o EGR System)

Hide 9.DISCONNECT ENGINE WIRE (w/o EGR System)

Hide 26100G 10.REMOVE INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

Hide 17118 11.REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

Hide 23704 12.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

a.
A152275

Remove the bolt and detach the injection pipe clamp.

NOTICE:

If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.



b.
A152276E06
0.056,0.035 0.244,0.186 0.187,0.151 10 *a 0.056,2.422 0.244,2.573 0.187,0.151 10 *b

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.

Text in Illustration
*a Injector Side
*b Common Rail Side


Hide 23770 14.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 11202D 16.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A223192

Disconnect the 4 injector connectors.


b.

Detach the 2 wire harness clamps and disconnect the wire harness from the No. 2 cylinder head cover.


c.
A152029

Remove the 4 bolts and No. 2 cylinder head cover.


Hide 11201 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:

If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.


a.
A060180E02
1.469,1.427 1.625,1.625 0.156,0.198 10 false .

Using a small screwdriver, remove the nozzle holder seal by prying the portion between the nozzle holder seal and the cutout part of the cylinder head cover.


b.
A223193

Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.


c.
A289511

Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


Hide 23670 18.REMOVE INJECTOR ASSEMBLY

a.
A060184E07
0.708,0.521 0.615,0.521 0.615,0.521 0.25,1.115 false 0.75,0.427 0.99,0.615 0.24,0.188 10 false *1

Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.

Text in Illustration
*1 Union Bolt

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the nozzle leakage pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




b.
G034876E02
1.292,0.771 1.448,0.969 0.156,0.198 10 false .

Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.



c.

Remove the O-ring from each injector.


d.

Remove the 4 injection nozzle seats from the cylinder head.