For more information on the injector assemblies and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).
If DTC P1238 has been stored, refer to Diagnostic Trouble Code Chart (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
The ECM detects combustion deterioration for a specific cylinder.
| *A | Injector Cross Section Diagram: | - | - |
| *1 | Solenoid Valve | *2 | Piston |
| *3 | Nozzle Needle | - | - |
The cylinder which has the compensation value, indicated by Injection Feedback Val #1, #2, #3 and #4, that varies from the other cylinders may be malfunctioning.
If DTC P0093 (fuel leaks from high-pressure area) is stored simultaneously, a leakage malfunction of a specific cylinder has probably occurred.
If DTC P0200 (open or short in the injector driver or injector circuit) is stored simultaneously, there is probably a faulty circuit located between the ECM and the injector assembly including the injector driver.
If only DTC P1238 (injector malfunction) has been stored, an injector assembly mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM, injector driver or injector circuit is unlikely.
| DTC Detection Drive Pattern | DTC Detection Condition | Main Trouble Area | Related Trouble Area |
|---|---|---|---|
| Warm up the engine and idle it for 60 seconds | A large engine speed fluctuation when idling continues for 60 seconds (2 trip detection logic). | ·
Injector assembly ·
Injector driver (P0200 stored simultaneously) ·
Connector connection (P0200 stored simultaneously) ·
Compression pressure |
·
Valve timing ·
Fuel with low cetane number used ·
ECM |
| DTC No. | Data List |
|---|---|
| P1238 | ·
Injection Volume ·
Injection Feedback Val #1 to #4 ·
Common Rail Pressure ·
Target Common Rail Pressure |
If DTC P1238 is stored, the following symptoms may appear:
Rough idle
Poor driveability
After confirming DTC P1238, check the internal fuel pressure on the intelligent tester by entering the following menus: Powertrain / Engine and ECT / Data List / Common Rail Pressure, Target Common Rail Pressure.
Under a stable condition such as idling or running the engine at 2500 rpm without load, Common Rail Pressure is within 5000 kPa of Target Common Rail Pressure.
This DTC will be stored if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM stores this DTC.
Refer to DTC P0200 (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>P0200).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
When this DTC is stored, be sure to carefully examine "Injection Feedback Val #1 to #4", "Injection Volume", "Common Rail Pressure", "Target Common Rail Pressure", "Engine Speed", "MAF", "Coolant Temp" and "Vehicle Speed" in the freeze frame data.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P1238 is output | A |
| P1238 and other DTCs are output | B |
If any DTCs other than P1238 are output, troubleshoot those DTCs first.
If DTCs other than P1238 are not output, check the fuel condition before proceeding to the next step.
A
B
Check the wire harness and connector connections.
The wire harness and connectors have been connected securely and there are good connections.
OK
NG
Read the injector compensation codes (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.
Read the value.
The compensatory injection volume is less than 3.0 mm3/st
If the fuel injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.
If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector assembly to inject.
Inspect and repair the cylinder that has an improper compensation value according to the following steps.
NEXT
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
Check the 4 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.
If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.
NEXT
Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.
Check the cylinder compression pressure (See page Engine / Hybrid System>1KD-FTV (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
OK
NG
Replace the injector assembly (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).
NEXT
Bleed the air from the fuel system (See page Engine / Hybrid System>1KD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION).
NEXT
Register the injector compensation code (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Perform the injector pilot quantity learning (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1238.
Check the DTC judgment result.
| Tester Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P1238 is output | A |
| All Readiness | ABNORMAL | A |
| NORMAL | B |
If STATUS is INCOMPLETE or N/A, increase the idling time.
A
B
Replace the ECM (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
NEXT
Repair or replace the harness or connector.
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P1238.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.
NEXT