The parking assist ECU and radio and display receiver assembly are connected by an AVC-LAN communication line. When an AVC-LAN communication error occurs between the radio and display receiver assembly and parking assist ECU, these DTCs will be stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15D8 | A device that is listed in the AVC-LAN connected device record of the master unit is missing. | ·
Parking assist ECU power source circuit ·
AVC-LAN circuit ·
Parking assist ECU ·
Radio and display receiver assembly |
Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
The radio and display receiver assembly is the master unit.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-4 (GND1) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-1 (+B) - I6-4 (GND1) | Always | 11 to 14 V |
| I6-8 (IG) - I6-4 (GND1) | Ignition switch ON | 11 to 14 V |
| I6-9 (ACC) - I6-4 (GND1) | Ignition switch ACC | 11 to 14 V |
| *a | Front view of wire harness connector
(to Parking Assist ECU) |
OK
NG
Remove the radio and display receiver assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (TX3+) - 8 (TX3-) | Always | 60 to 80 Ω |
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
Disconnect the H50 radio and display receiver assembly connector.
Disconnect the I6 parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H50-7 (TX3+) - I6-11 (TX+) | Always | Below 1 Ω |
| H50-8 (TX3-) - I6-10 (TX-) | Always | Below 1 Ω |
| H50-7 (TX3+) - Body ground | Always | 10 kΩ or higher |
| H50-8 (TX3-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the parking assist ECU with a known good one.
Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)