CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for 5L-E)
| *A | for LHD | *B | for RHD |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the driver side junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-30 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-31 (ALTB) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-32 (IG) - Body ground | - | Ignition switch power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2I-27 (FLCY) - Body ground*1 | R - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | |||
| 2D-31 (FLCY) - Body ground*2 | R - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | |||
| 2D-15 (FRCY) - Body ground*1 | B - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | |||
| 2H-26 (FRCY) - Body ground*2 | B - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | |||
| G65-3 (LCTY) - Body ground | V - Body ground | Rear door LH courtesy light switch input | Rear door LH open | Below 1 V |
| Rear door LH closed | 11 to 14 V | |||
| G64-6 (RCTY) - Body ground | R - Body ground | Rear door RH courtesy light switch input | Rear door RH open | Below 1 V |
| Rear door RH closed | 11 to 14 V | |||
| G64-19 (BCTY) - Body ground | G - Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| Ignition switch off, all doors closed and back door closed | 11 to 14 V | |||
| G64-11 (L2) - Body ground | GR - Body ground | Driver side door key-linked lock input | Driver side door key cylinder in lock position | Below 1 V |
| Ignition switch off, all doors closed and driver side door key cylinder in neutral position | 11 to 14 V | |||
| G64-24 (UL3) - Body ground | LG - Body ground | Driver side door key-linked unlock input | Driver side door key cylinder in unlock position | Below 1 V |
| Ignition switch off, all doors closed and driver side door key cylinder in neutral position | 11 to 14 V | |||
| 2D-3 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2I-8 (ACT+) - Body ground*1 | L - Body ground | Door lock motor lock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2H-8 (ACT+) - Body ground*2 | L - Body ground | Door lock motor lock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2D-1 (ACTD) - Body ground | G - Body ground | Driver side door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2D-2 (ACT-) - Body ground | W - Body ground | Door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2I-10 (ACT-) - Body ground*1 | W - Body ground | Door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2H-10 (ACT-) - Body ground*1 | W - Body ground | Door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| G64-7 (LSFL) - Body ground | G - Body ground | Front door LH lock position switch input | Front door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door LH locked | 11 to 14 V | |||
| G64-18 (LSFR) - Body ground | G - Body ground | Front door RH lock position switch input | Front door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door RH locked | 11 to 14 V | |||
| 2I-25 (LSWL) - Body ground*1 | B - Body ground | Rear door LH lock position switch input | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door LH locked | 11 to 14 V | |||
| 2D-16 (LSWL) - Body ground*2 | B - Body ground | Rear door LH lock position switch input | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door LH locked | 11 to 14 V | |||
| G63-2 (LSWR) - Body ground | V - Body ground | Rear door RH lock position switch input | Rear door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and rear door RH locked | 11 to 14 V | |||
| G65-13 (LSWB) - Body ground | SB - Body ground | Back door lock position switch input | Back door lock unlocked | Below 1 V |
| Ignition switch off, all doors closed and back door locked | 11 to 14 V | |||
| 2A-25 (GSW) - Body ground | B - Body ground | Center airbag sensor signal | Ignition switch ON with the center airbag sensor assembly connector disconnected | 4.3 to 5.5 V |
*1: for LHD
*2: for RHD
CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (except 5L-E)
| *A | Main Body ECU (Multiplex Network Body ECU) with 3 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 connectors | *B | for LHD |
| *C | for RHD | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Connect the driver side junction block assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-32 (IG) - Body ground | - | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-31 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-30 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
Install the main body ECU (multiplex network body ECU).
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for LHD *2: for RHD *3: for 5 Door *4: w/ Door Control Battery *5: Door control battery not charged *6: Door control battery charging or charged |
||||
| G218-6 (FLCY) - Body ground | R - Body ground | Front door courtesy light switch assembly LH signal | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | |||
| G218-27 (FRCY) - Body ground | B - Body ground | Front door courtesy light switch assembly RH signal | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | |||
| 2N-30 (RCTY) - Body ground*1, *3 | R - Body ground | Rear door courtesy light switch assembly RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | 11 to 14 V | |||
| 2P-23 (RCTY) - Body ground*2, *3 | R - Body ground | Rear door courtesy light switch assembly RH signal | Rear door RH open | Below 1 V |
| Rear door RH closed | 11 to 14 V | |||
| 2Q-33 (LCTY) - Body ground*1, *3 | V - Body ground | Rear door courtesy light switch assembly LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | 11 to 14 V | |||
| 2O-15 (LCTY) - Body ground*2, *3 | V - Body ground | Rear door courtesy light switch assembly LH signal | Rear door LH open | Below 1 V |
| Rear door LH closed | 11 to 14 V | |||
| 2Q-27 (BCTY) - Body ground*1 | G - Body ground | Back door courtesy light switch assembly signal | Back door open | Below 1 V |
| Back door close | 11 to 14 V | |||
| 2N-27 (BCTY) - Body ground*2 | G - Body ground | Back door courtesy light switch assembly signal | Back door open | Below 1 V |
| Back door close | 11 to 14 V | |||
| G218-29 (L2) - Body ground | GR - Body ground | Driver side door key-linked lock input | Driver side door key cylinder in lock position | Below 1 V |
| Ignition switch off, all doors closed and driver side door key cylinder in neutral position | 11 to 14 V | |||
| G218-2 (UL3) - Body ground | LG - Body ground | Driver side door key-linked unlock input | Driver side door key cylinder in unlock position | Below 1 V |
| Ignition switch off, all doors closed and driver side door key cylinder in neutral position | 11 to 14 V | |||
| G216-3 (ACTG) - Body ground*4 | R - Body ground | Collision door lock release signal | Collision door lock release function does not operate | Below 2 V*5
7.3 to 10.1 V*6 |
| Collision door lock release function operates | Below 1 V | |||
| 2N-3 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2Q-9 (ACT+) - Body ground*1, *3 | L - Body ground | Door lock motor lock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2P-9 (ACT+) - Body ground*2 | L - Body ground | Door lock motor lock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V | |||
| 2N-4 (ACTD) - Body ground | G - Body ground | Driver side door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2N-5 (ACT-) - Body ground | W - Body ground | Door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2Q-8 (ACT-) - Body ground*1, *3 | W - Body ground | Door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2P-8 (ACT-) - Body ground*2 | W - Body ground | Door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V | |||
| 2O-41 (LSFR) - Body ground | G - Body ground | Front door unlock detection switch RH signal | Front door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door RH locked | 11 to 14 V | |||
| 2N-12 (LSFL) - Body ground | G - Body ground | Front door unlock detection switch LH signal | Front door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed and front door LH locked | 11 to 14 V | |||
| 2Q-26 (LSWL) - Body ground*1, *3 | B - Body ground | Rear door unlock detection switch LH signal | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed, rear door LH locked | 11 to 14 V | |||
| 2O-38 (LSWL) - Body ground*2, *3 | B - Body ground | Rear door unlock detection switch LH signal | Rear door LH unlocked | Below 1 V |
| Ignition switch off, all doors closed, rear door LH locked | 11 to 14 V | |||
| G216-2 (LSWR) - Body ground*3 | V - Body ground | Rear door unlock detection switch RH signal | Rear door RH unlocked | Below 1 V |
| Ignition switch off, all doors closed, rear door RH locked | 8 to 12 V | |||
| G218-17 (LSWB) - Body ground | SB - Body ground | Back door unlock detection switch signal | Back door unlocked | Below 1 V |
| Ignition switch off, all doors closed, back door locked | 11 to 14 V | |||
| 2O-46 (GSW) - Body ground | B - Body ground | Center airbag sensor signal | Ignition switch ON with the center airbag sensor assembly connector disconnected | 4.3 to 5.5 V |
CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)
Disconnect the G212 double lock door control relay assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G212-12 (+B) - Body ground | R - Body ground | Battery power supply | Always | 11 to 14 V |
| G212-11 (CPUB) - Body ground | P - Body ground | Battery power supply | Always | 11 to 14 V |
| G212-7 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the G212 double lock door control relay assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G212-8 (ACTS) - Body ground | L - Body ground | All door double lock motor set on output | Double lock unset → set | Below 1 V → 11 to 14 V |
| G212-1 (ACTR) - Body ground | W - Body ground | All door double lock motor set off output | Double lock set → unset | Below 1 V → 11 to 14 V |
| G212-6 (DLPD) - Body ground | V - Body ground | Driver door double lock position switch input | Double lock unset → set | Pulse generation → Below 1 V |
| G212-5 (DLPP) - Body ground | V - Body ground | Front passenger door double lock position switch input | Double lock unset → set | Pulse generation → Below 1 V |
| G212-3 (DLPL) - Body ground* | G - Body ground | Rear left door double lock position switch input | Double lock unset → set | Pulse generation → Below 1 V |
| G212-4 (DLPR) - Body ground* | R - Body ground | Rear right door double lock position switch input | Double lock unset → set | Pulse generation → Below 1 V |
*: for 5 Door
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION
CHECK AIRBAG SENSOR ASSEMBLY
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU