Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror) › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0327116 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch  


DESCRIPTION

When the outer mirror switch assembly mirror surface adjust switch (up/down/left/right) is operated, up/down/left/right signals are received by the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends the received signals to the outer mirror control ECU assembly RH*1 and LH*2 via CAN communication. The outer mirror control ECU assembly RH*1 and LH*2 receives the remote mirror selection signal and up/down/left/right signals and operates the outer rear view mirror assembly RH*1 and LH*2 up/down/left/right based on the signals.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

for LHD:
E378105E02
1.271,3.917 3.219,4.146 1.948,0.229 10 false Outer Mirror Switch Assembly 5.5,0.656 5.979,0.896 0.479,0.24 10 false MIRB 5.5,2.417 5.958,2.615 0.458,0.198 10 false MIRS 5.51,3.094 6.125,3.292 0.615,0.198 10 false MIRE 3.354,1.208 4.281,1.667 0.927,0.458 10 false Mirror Surface Adjust Switch 0.833,0.927 1.135,1.135 0.302,0.208 10 false Left 1.646,0.906 2.052,1.104 0.406,0.198 10 false Down 2.458,0.917 2.948,1.115 0.49,0.198 10 false Right 3.281,0.896 3.594,1.094 0.313,0.198 10 false Up 0.719,2.646 1.042,2.854 0.323,0.208 10 false Left 1.594,2.615 2.365,2.813 0.771,0.198 10 false Right 2.156,2.615 2.479,2.823 0.323,0.208 10 false Left 3.031,2.604 3.438,2.792 0.406,0.188 10 false Right 1.417,3.26 2.74,3.5 1.323,0.24 10 false Mirror Select Switch 1.25,3.74 1.708,3.938 0.458,0.198 10 false G11 4.51,0.542 4.667,0.74 0.156,0.198 10 false B 4.719,0.563 5.031,0.76 0.313,0.198 10 false 13 5.271,0.573 5.583,0.771 0.313,0.198 10 false 4 4.198,2.292 4.656,2.49 0.458,0.198 10 false MSW 4.729,2.313 5.042,2.51 0.313,0.198 10 false 14 5.281,2.958 5.438,3.156 0.156,0.198 10 false 6 4.115,2.969 4.729,3.167 0.615,0.198 10 false MSWR 4.74,2.948 5.052,3.146 0.313,0.198 10 false 12 5.281,2.344 5.438,2.542 0.156,0.198 10 false 5 5.156,4.073 6.823,4.469 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 5.146,3.854 5.76,4.052 0.615,0.198 10 false G217 0.667,7.406 2.396,7.615 1.729,0.208 10 false : CAN Communication Line 0.802,6.771 3.302,7 2.5,0.229 10 false Outer Rear View Mirror Assembly RH 5.365,6.75 5.823,6.948 0.458,0.198 10 false z19 0.844,5.563 2.167,5.771 1.323,0.208 10 false Vertical Mirror Motor 0.719,5.948 2.146,6.156 1.427,0.208 10 false Horizontal Mirror Motor 5.531,5.375 5.844,5.573 0.313,0.198 10 false MV 5.521,5.75 5.833,5.948 0.313,0.198 10 false M+ 5.51,6.135 5.823,6.333 0.313,0.198 10 false MH 5.396,6.938 6.615,7.354 1.219,0.417 10 false Outer Mirror Control ECU Assembly RH 5.292,5.25 5.448,5.448 0.156,0.198 10 false 1 5.25,5.656 5.469,5.865 0.219,0.208 10 false 10 5.292,6.042 5.448,6.24 0.156,0.198 10 false 9

for RHD:
E378106E02
5.406,6.875 6.646,7.333 1.24,0.458 10 false Outer Mirror Control ECU Assembly LH 5.406,6.729 5.865,6.927 0.458,0.198 10 false z18 5.583,5.396 5.896,5.594 0.313,0.198 10 false MV 5.573,5.76 5.885,5.958 0.313,0.198 10 false M+ 5.573,6.135 5.885,6.333 0.313,0.198 10 false MH 5.333,5.281 5.49,5.479 0.156,0.198 10 false 1 5.271,5.646 5.542,5.885 0.271,0.24 10 false 10 5.323,6.021 5.594,6.26 0.271,0.24 10 false 9 0.688,7.417 2.417,7.635 1.729,0.219 10 false : CAN Communication Line 0.875,5.563 2.146,5.781 1.271,0.219 10 false Vertical Mirror Motor 0.74,5.958 2.25,6.208 1.51,0.25 10 false Horizontal Mirror Motor 5.167,4.042 6.833,4.448 1.667,0.406 10 false Main Body ECU (Multiplex Network Body ECU) 1.49,3.74 3.406,3.979 1.917,0.24 10 false Outer Mirror Switch Assembly 1.49,3.573 2.104,3.771 0.615,0.198 10 false G196 0.865,3.052 4.125,3.281 3.26,0.229 10 false Mirror Select Switch / Mirror Surface Adjust Switch 1.99,2.354 2.292,2.542 0.302,0.188 10 false Left 3.083,2.333 3.51,2.552 0.427,0.219 10 false Right 0.729,1.417 1.031,1.604 0.302,0.188 10 false Left 1.594,1.385 2.208,1.583 0.615,0.198 10 false Down 2.49,1.365 3.26,1.563 0.771,0.198 10 false Right 3.375,1.375 3.688,1.573 0.313,0.198 10 false Up 4.635,0.802 4.792,1 0.156,0.198 10 false B 4.354,2 4.792,2.25 0.438,0.25 10 false MSW 4.281,2.573 4.823,2.844 0.542,0.271 10 false MSWR 4.854,2 5.198,2.219 0.344,0.219 11 false 13 4.865,0.802 5.208,1.021 0.344,0.219 11 false 15 4.854,2.552 5.198,2.771 0.344,0.219 11 false 12 5.604,0.906 6.219,1.104 0.615,0.198 10 false MIRB 5.333,0.792 5.677,1.01 0.344,0.219 11 false 4 5.344,2.021 5.688,2.24 0.344,0.219 11 false 5 5.344,2.563 5.688,2.781 0.344,0.219 11 false 6 5.594,2.146 6.208,2.344 0.615,0.198 10 false MIRS 5.563,2.729 6.177,2.927 0.615,0.198 10 false MIRE 5.177,3.865 5.792,4.063 0.615,0.198 10 false G217 0.938,6.76 3.24,6.969 2.302,0.208 10 false Outer Rear View Mirror Assembly LH

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery



PROCEDURE

1.READ VALUE USING GTS (OUTER MIRROR SWITCH ASSEMBLY)
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Mirror Selection SW (R) Mirror select switch signal for RH mirror / OFF or ON OFF: Mirror select switch neutral position (off)
ON: Mirror select switch R switch on
-
Mirror Selection SW (L) Mirror select switch signal for LH mirror / OFF or ON OFF: Mirror select switch neutral position (off)
ON: Mirror select switch L switch on
-
Mirror Position SW (R) Mirror surface adjust switch signal (Right) / OFF or ON OFF: Mirror surface adjust switch not pressed right
ON: Mirror surface adjust switch pressed right
Check with the mirror select switch L or R switch on
Mirror Position SW (L) Mirror surface adjust switch signal (Left) / OFF or ON OFF: Mirror surface adjust switch not pressed left
ON: Mirror surface adjust switch pressed left
Check with the mirror select switch L or R switch on
Mirror Position SW (Up) Mirror surface adjust switch signal (Up) / OFF or ON OFF: Mirror surface adjust switch not pressed up
ON: Mirror surface adjust switch pressed up
Check with the mirror select switch L or R switch on
Mirror Position SW (Dwn) Mirror surface adjust switch signal (Down) / OFF or ON OFF: Mirror surface adjust switch not pressed down
ON: Mirror surface adjust switch pressed down
Check with the mirror select switch L or R switch on

OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE)

NG

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE)
a.

Remove the outer rear view mirror assembly (front passenger side).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly (front passenger side).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER SIDE)

3.INSPECT OUTER MIRROR SWITCH ASSEMBLY
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])
a.

Disconnect the G11*1 or G196*2 outer mirror switch assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G217 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G11-13 (B) - G217-4 (MIRB) Always Below 1 Ω
G11-14 (MSW) - G217-5 (MIRS) Always Below 1 Ω
G11-12 (MSWR) - G217-6 (MIRE) Always Below 1 Ω
G11-13 (B) or G217-4 (MIRB) - Body ground Always 10 kΩ or higher
G11-14 (MSW) or G217-5 (MIRS) - Body ground Always 10 kΩ or higher
G11-12 (MSWR) or G217-6 (MIRE) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G196-15 (B) - G217-4 (MIRB) Always Below 1 Ω
G196-13 (MSW) - G217-5 (MIRS) Always Below 1 Ω
G196-12 (MSWR) - G217-6 (MIRE) Always Below 1 Ω
G196-15 (B) or G217-4 (MIRB) - Body ground Always 10 kΩ or higher
G196-13 (MSW) or G217-5 (MIRS) - Body ground Always 10 kΩ or higher
G196-12 (MSWR) or G217-6 (MIRE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR