Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror) › from 2017.08
RM27T0E _59 Vehicle Exterior _053745 MIRROR (EXT) _0327116 POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Reverse Shift-linked Mirror)  Power Retractable Mirrors do not Operate with Power Retract Mirror Switch  


DESCRIPTION

When the outer mirror switch assembly mirror retract switch is operated, deploy/retract signals are sent to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) sends deploy/retract signals to the outer mirror control ECU assembly via CAN communication. The outer mirror control ECU assembly deploys and retracts the outer rear view mirror assembly based on the received signals.

WIRING DIAGRAM

E378109E01
0.906,2.74 2.854,3.01 1.948,0.271 10 false Outer Mirror Switch Assembly 0.906,2.563 2.896,2.76 1.99,0.198 10 false G11*1, G196*2 0.281,6.781 1.031,6.969 0.75,0.188 10 false *1: for LHD 0.271,7.094 1.021,7.281 0.75,0.188 10 false *2: for RHD 0.677,7.406 2.385,7.583 1.708,0.177 10 false : CAN Communication Line 5.073,1.938 6.74,2.26 1.667,0.323 10 false Main Body ECU (Multiplex Network Body ECU) 5.198,4.667 5.49,4.875 0.292,0.208 10 false z18 5.146,6.885 5.469,7.115 0.323,0.229 10 false z19 5.167,4.865 6.719,5.26 1.552,0.396 10 false Outer Mirror Control ECU Assembly LH 5.135,7.042 6.688,7.438 1.552,0.396 10 false Outer Mirror Control ECU Assembly RH 1.667,4.052 3.396,4.302 1.729,0.25 10 false Power Retract Mirror Motor 1.938,4.594 4.281,4.813 2.344,0.219 10 false Outer Rear View Mirror Assembly LH 1.833,6.823 4.177,7.042 2.344,0.219 10 false Outer Rear View Mirror Assembly RH 2.99,0.271 3.76,0.469 0.771,0.198 10 false MR 3.354,0.25 4.125,0.448 0.771,0.198 10 false 8*1, 17*2 5.083,1.771 5.698,1.969 0.615,0.198 10 false G216 5.167,0.219 5.938,0.417 0.771,0.198 10 false 14 2.927,0.542 3.698,0.74 0.771,0.198 10 false MAT 3.344,0.542 4.115,0.74 0.771,0.198 10 false 11 5.438,0.677 6.354,0.875 0.917,0.198 10 false AMR 5.156,0.552 5.927,0.75 0.771,0.198 10 false 11 5.448,0.375 6.365,0.573 0.917,0.198 10 false RET 5.458,3.833 5.771,4.031 0.313,0.198 10 false MR 5.458,4.219 5.771,4.417 0.313,0.198 10 false MF 5.458,6.458 5.771,6.656 0.313,0.198 10 false MF 5.458,6.094 5.771,6.292 0.313,0.198 10 false MR 5.24,3.74 5.396,3.938 0.156,0.198 10 false 3 5.177,4.115 5.427,4.323 0.25,0.208 10 false 11 5.167,6.333 5.5,6.531 0.333,0.198 10 false 11 5.219,5.958 5.375,6.156 0.156,0.198 10 false 3 3.104,1.75 3.26,1.948 0.156,0.198 10 false E 3.375,1.75 4.146,1.948 0.771,0.198 10 false 10 0.885,0.802 1.5,1 0.615,0.198 10 false Fold 2.458,0.823 3.375,1.021 0.917,0.198 10 false Unfold 1.688,0.573 2.302,0.771 0.615,0.198 10 false Auto 1.146,2.031 2.5,2.271 1.354,0.24 10 false Mirror Retract Switch 1.688,6.271 3.417,6.521 1.729,0.25 10 false Power Retract Mirror Motor

CAUTION / NOTICE / HINT

NOTICE:
·

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this problem.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery



PROCEDURE

1.READ VALUE USING GTS (OUTER MIRROR FOLD SW)
a.

Using the GTS, read the Data List.

Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM (w/ Reverse Shift-linked Mirror)>DATA LIST / ACTIVE TEST

Body Electrical > Main Body > Data List
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Outer Mirror Fold SW Mirror retract switch signal / OFF or ON OFF: Mirror retract switch not in retract position
ON: Mirror retract switch in retract position
-


OK:

On the GTS screen, ON or OFF is displayed for each item according to the table above.


Result:
Proceed to
OK
NG



OK

2.CHECK MALFUNCTIONING PARTS

NG

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACT SWITCH)
2.CHECK MALFUNCTIONING PARTS

Result:
Result Proceed to
Both mirrors are malfunctioning A
LH side mirror is malfunctioning B
RH side mirror is malfunctioning C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (POWER RETRACT FUNCTION)

C

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (POWER RETRACT FUNCTION)
3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (POWER RETRACT FUNCTION)
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPLACE SMART DOOR CONTROL RECEIVER ASSEMBLY

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (POWER RETRACT FUNCTION)
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY (MIRROR RETRACT SWITCH)
a.

Remove the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>REMOVAL


b.

Inspect the outer mirror switch assembly.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)

NG

REPLACE OUTER MIRROR SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] AND BODY GROUND)
a.

Disconnect the G11*1 or G196*2 outer mirror switch assembly connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G216 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G11-8 (MR) - G216-14 (RET) Always Below 1 Ω
G11-11 (MAT) - G216-11 (AMR) Always Below 1 Ω
G11-10 (E) - Body ground Always Below 1 Ω
G11-8 (MR) or G216-14 (RET) - Body ground Always 10 kΩ or higher
G11-11 (MAT) or G216-11 (AMR) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G196-17 (MR) - G216-14 (RET) Always Below 1 Ω
G196-11 (MAT) - G216-11 (AMR) Always Below 1 Ω
G196-10 (E) - Body ground Always Below 1 Ω
G196-17 (MR) or G216-14 (RET) - Body ground Always 10 kΩ or higher
G196-11 (MAT) or G216-11 (AMR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR