Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1379  Downhill Assist Control Switch Malfunction (Test Mode DTC)  


DESCRIPTION

w/o Combination Switch (w/ Downhill Assist Control):

DTC C1379 is cleared when the downhill assist control switch sends a downhill assist control operation signal or when test mode ends.

w/ Combination Switch:

DTC C1379 is cleared when the crawl on/off switch (combination switch assembly) and crawl speed selector (combination switch assembly) send a crawl control operation signal or when test mode ends.

DTC Code DTC Detection Condition Trouble Area
C1379 Stored only during test mode.
·

Downhill assist control switch (w/o Combination Switch (w/ Downhill Assist Control))

·

Crawl on/off switch (Combination switch assembly) (w/ Crawl Control)

·

Crawl speed selector (Combination switch assembly) (w/ Crawl Control)

·

Harness or connector

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C214516E15
0.146,0.073 2.688,0.271 2.542,0.198 12 false w/o Combination Switch: 1.833,1.375 3.76,1.583 1.927,0.208 10 false Downhill Assist Control Switch 5.323,0.948 5.781,1.115 0.458,0.167 10 false HZRI 4.99,0.792 5.229,1 0.24,0.208 10 false 28 4.885,1.667 6.583,2.073 1.698,0.406 10 false Skid Control ECU (Master Cylinder Solenoid) 4.885,1.531 5.094,1.698 0.208,0.167 10 false A7 1.823,1.24 2.542,1.396 0.719,0.156 10 false G232 3.396,0.76 3.552,0.958 0.156,0.198 10 false 5 1.99,0.771 2.115,0.969 0.125,0.198 10 false 2 2.917,0.771 3.375,0.938 0.458,0.167 10 false +B2 2.271,0.76 2.729,0.927 0.458,0.167 10 false E

C214516E16
0.146,0.073 2.688,0.271 2.542,0.198 12 false w/ Combination Switch: 1.802,1.365 4.573,1.729 2.771,0.365 10 false Downhill Assist Control Switch (Combination Switch Assembly) 5.323,0.948 5.781,1.115 0.458,0.167 10 false HZRI 4.99,0.792 5.229,1 0.24,0.208 10 false 28 4.885,1.667 6.583,2.073 1.698,0.406 10 false Skid Control ECU (Master Cylinder Solenoid) 4.885,1.531 5.094,1.698 0.208,0.167 10 false A7 1.781,1.24 2.5,1.396 0.719,0.156 10 false G306 3.396,0.76 3.552,0.958 0.156,0.198 10 false 5 1.99,0.771 2.115,0.969 0.125,0.198 10 false 2 2.917,0.771 3.375,0.938 0.458,0.167 10 false +B2 2.271,0.76 2.729,0.927 0.458,0.167 10 false E

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

Check the Data List for proper functioning of the downhill assist control switch.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Downhill Assist Control SW Downhill assist control switch / ON or OFF ON: Downhill assist control on
OFF: Downhill assist control off
-

OK:

The GTS displays ON or OFF according to downhill assist control switch operation.


Result
Result Proceed to
OK A
NG (w/o Crawl Control) B
NG (w/ Crawl Control) C



A

2.CHECK TEST MODE DTC

B

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH

C

5.INSPECT COMBINATION SWITCH ASSEMBLY
2.CHECK TEST MODE DTC
a.

Perform the downhill assist control switch check in the Test Mode Procedure (See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>TEST MODE PROCEDURE).

OK:

Test mode DTC C1379 is cleared.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

C

3.INSPECT DOWNHILL ASSIST CONTROL SWITCH

OK

4.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - DOWNHILL ASSIST CONTROL SWITCH)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the G232 downhill assist control switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-28 (HZRI) - G232-5 (+B2) Always Below 1 Ω
A7-28 (HZRI) or G232-5 (+B2) - Body ground Always 10 kΩ or higher
G232-2 (E) - Body ground Always Below 1 Ω


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMBINATION SWITCH ASSEMBLY
a.

Remove the combination switch assembly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.

Inspect the combination switch assembly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - MASTER CYLINDER SOLENOID)

NG

REPLACE COMBINATION SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - MASTER CYLINDER SOLENOID)
a.

Disconnect the G156 downhill assist control switch (combination switch assembly) connector.


b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-28 (HZRI) - G306-5 (+B2) Always Below 1 Ω
A7-28 (HZRI) or G306-5 (+B2) - Body ground Always 10 kΩ or higher
G306-2 (E) - Body ground Always Below 1 Ω


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR