Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B491335N01
3.25,0.469 3.667,0.667 0.417,0.198 1.667,0.469 2.083,0.667 0.417,0.198 5,0.469 5.417,0.667 0.417,0.198 1.698,0.479 2.313,0.677 0.615,0.198 10 false G213 3.281,0.479 3.896,0.677 0.615,0.198 10 false G214 5.042,0.479 5.656,0.677 0.615,0.198 10 false G215

a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G215-11 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
G215-10 (+B) - G215-11 (E) Input V - W-B Power supply Always 11 to 14 V -


c.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
G213-3 (IG1D) - G215-11 (E) Output V - W-B IG power supply Engine switch off → on (IG) 1 V or less → 8.5 V or higher -
G215-4 (CLG1) - G215-11 (E) Output R - W-B Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
G215-4 (CLG1) - G215-11 (E) Input R - W-B Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor ON signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Driver door lock sensor touched


Pulse generation
(See waveform 10)
D-Door Trigger Switch
G215-4 (CLG1) - G215-11 (E) Input R - W-B Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor touched


Pulse generation
(See waveform 11)
D-Door Touch Sensor
G215-3 (CG1B) - G215-11 (E) Output G - W-B Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 3)
Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 4)
G215-2 (CLG2) - G215-11 (E) Output B - W-B Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 1)
Overhead + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 2)
G215-2 (CLG2) - G215-11 (E) Input B - W-B Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor ON signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)

5.

Front passenger door lock sensor touched


Pulse generation
(See waveform 10)
P-Door Trigger Switch
G215-2 (CLG2) - G215-11 (E) Input B - W-B Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor touched


Pulse generation
(See waveform 11)
P-Door Touch Sensor
G215-1 (CG2B) - G215-11 (E) Output W - W-B Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*1)


Pulse generation
(See waveform 3)
Overhead + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*1)


Pulse generation
(See waveform 4)
G215-21 (CLG5) - G215-11 (E) Output R - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 5)
Overhead + Front Room (key diagnostic mode)
G215-20 (CG5B) - G215-11 (E) Output W - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 5)
Overhead + Front Room (key diagnostic mode)
G214-5 (TSW5) - G215-11 (E) Input G - W-B Back door opener switch assembly (unlock switch) signal input Back door opener switch assembly (unlock switch) off → on Pulse generation
(See waveform 7)
Tr/B-Door Unlock SW
G214-13 (TSW6) - G215-11 (E) Input L - W-B Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch) off → on Pulse generation
(See waveform 7)
Tr/B-Door Lock SW
G214-15 (CLG6) - G215-11 (E) Output Y - W-B Output to No. 2 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 5)
Overhead + Rear Room (key diagnostic mode)
G214-14 (CG6B) - G215-11 (E) Output W - W-B Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 5)
Overhead + Rear Room (key diagnostic mode)
G214-4 (CLG7) - G215-11 (E) Output LG - W-B Output to No. 3 indoor electrical key antenna assembly (inside luggage) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 5)
Overhead + Back Door (inside) (key diagnostic mode)
G214-3 (CG7B) - G215-11 (E) Output L - W-B Output to No. 3 indoor electrical key antenna assembly (inside luggage) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


Pulse generation
(See waveform 5)
Overhead + Back Door (inside) (key diagnostic mode)
G214-18 (RCO) - G215-11 (E) Output L - W-B Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 8)
-
G214-19 (CSEL) - G215-11 (E) Output P - W-B Communication channel switching circuit Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → pulse generation -
G214-20 (RDAM) - G215-11 (E) Input G - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 9)
-
G214-2 (CLG8) - G215-11 (E) Output B - W-B Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation
(See waveform 6)
Overhead + Back Door (key diagnostic mode)
G214-1 (CG8B) - G215-11 (E) Output W - W-B Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation
(See waveform 6)
Overhead + Back Door (key diagnostic mode)

*1: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

*2: for LHD

*3: for RHD



e.
B340872N01
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection G215-4 (CLG1) - G215-11 (E)
G215-2 (CLG2) - G215-11 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



f.
B340873N01
0.177,1.021 0.635,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection G215-4 (CLG1) - G215-11 (E)
G215-2 (CLG2) - G215-11 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



g.
B367472N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 3.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection G215-3 (CG1B) - G215-11 (E)
G215-1 (CG2B) - G215-11 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



h.
B367473N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 4.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection G215-3 (CG1B) - G215-11 (E)
G215-1 (CG2B) - G215-11 (E)
Tool Setting 5 V/DIV., 100 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



i.
B340874C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 1.01,1.917 1.469,2.115 0.458,0.198 10 false *a 2.135,1.938 2.594,2.135 0.458,0.198 10 false *b
*a For 30 seconds after closing any door using the door outside handle
*b 30 seconds or more have elapsed after closing any door using the door outside handle


Using an oscilloscope, check waveform 5

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 5 (Reference)
Item Content
Tester Connection G215-21 (CLG5) - G215-11 (E)
G215-20 (CG5B) - G215-11 (E)
G214-15 (CLG6) - G215-11 (E)
G214-14 (CG6B) - G215-11 (E)
G214-4 (CLG7) - G215-11 (E)
G214-3 (CG7B) - G215-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle




j.
B340876N01
0.177,1.042 0.635,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 6.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection G214-2 (CLG8) - G215-11 (E)
G214-1 (CG8B) - G215-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on




k.
B251023C09
1.333,0.49 1.99,0.125 1.99,0.125 2.208,0.125 false 1.99,0.135 1.74,0.51 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.25,0.031 2.427,0.208 0.177,0.177 10 false *a
*a Checking for switch ON signal at short intervals


Using an oscilloscope, check waveform 7.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection G214-5 (TSW5) - G215-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Back door opener switch assembly (unlock switch) off → on

Waveform 7 (Reference)
Item Content
Tester Connection G214-13 (TSW6) - G215-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Back door opener switch assembly (lock switch) off → on


l.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 8.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection G214-18 (RCO) - G215-11 (E)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




m.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 9.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 9 (Reference)
Item Content
Tester Connection G214-20 (RDAM) - G215-11 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




n.
B340877C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 0.677,1.917 1.135,2.115 0.458,0.198 10 false *a 1.646,2 1.969,2.156 0.323,0.156 10 false *b 2.615,1.917 3.073,2.115 0.458,0.198 10 false *a
*a Lock sensor not touched
*b Lock sensor touched


Using an oscilloscope, check waveform 10.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 10 (Reference)
Item Content
Tester Connection G215-4 (CLG1) - G215-11 (E)
G215-2 (CLG2) - G215-11 (E)
Tool Setting 5 V/DIV., 40 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Lock sensor not touched → touched



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



o.
B340879C02
0.177,1.052 0.635,1.25 0.458,0.198 10 false GND 0.344,1.906 0.802,2.104 0.458,0.198 10 false *a 2.115,1.906 2.573,2.104 0.458,0.198 10 false *a 1.229,1.969 1.667,2.167 0.438,0.198 10 false *b
*a Unlock sensor not touched
*b Unlock sensor touched


Using an oscilloscope, check waveform 11.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 11 (Reference)
Item Content
Tester Connection G215-4 (CLG1) - G215-11 (E)
G215-2 (CLG2) - G215-11 (E)
Tool Setting 5 V/DIV., 50 ms./DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Unlock sensor not touched → touched





CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E373864C01
3.271,7.844 3.781,8.083 0.51,0.24 4.583,6.177 5.094,6.417 0.51,0.24 1.469,6.177 1.979,6.417 0.51,0.24 1.271,4.677 1.781,4.917 0.51,0.24 3.708,4.469 4.219,4.708 0.51,0.24 5.24,4.469 5.75,4.708 0.51,0.24 6.26,4.448 6.771,4.688 0.51,0.24 5.583,3.094 6.094,3.333 0.51,0.24 3.49,3.083 4,3.323 0.51,0.24 1.271,3.135 1.781,3.375 0.51,0.24 1.271,4.354 1.781,4.594 0.51,0.24 1.604,0.646 1.604,0.417 1.604,0.417 1.76,0.417 false 0.615,1.302 0.948,1.302 true 1.625,1.156 1.958,1.156 true 1.635,1.469 1.969,1.469 true 1.646,1.833 1.979,1.833 true 1.823,0.292 2.135,0.49 0.313,0.198 10 false *1 0.125,0.125 0.51,0.385 0.385,0.26 12 false *A 0.229,1.188 0.615,1.563 0.385,0.375 10 false 2Q*B 2P*C 0.854,1.792 1.24,2.167 0.385,0.375 10 false 2M 0.896,2.229 1.281,2.604 0.385,0.375 10 false 2K 0.917,2.448 1.302,2.823 0.385,0.375 10 false 2L 3.781,0.969 4.167,1.344 0.385,0.375 10 false A 5.844,1.094 6.229,1.469 0.385,0.375 10 false 2N 5.844,1.76 6.229,2.135 0.385,0.375 10 false 2O 3.469,7.875 3.854,8.25 0.385,0.375 10 false A 6.427,4.479 6.813,4.854 0.385,0.375 10 false 2L 5.406,4.49 5.792,4.865 0.385,0.375 10 false 2K 3.854,4.49 4.24,4.865 0.385,0.375 10 false 2M 1.427,4.375 1.813,4.75 0.385,0.375 10 false 2Q 1.438,4.698 1.823,5.073 0.385,0.375 10 false 2P 1.854,4.698 2.24,5.073 0.385,0.375 10 false *C 1.854,4.396 2.24,4.771 0.385,0.375 10 false *B 1.615,6.208 2,6.583 0.385,0.375 10 false 2N 4.74,6.198 5.125,6.573 0.385,0.375 10 false 2O 2.01,1.698 2.552,2 0.542,0.302 10 false G216 1.344,3.156 1.885,3.458 0.542,0.302 10 false G216 2.021,1.031 2.563,1.333 0.542,0.302 10 false G217 5.667,3.115 6.208,3.417 0.542,0.302 10 false G217 3.583,3.104 4.125,3.406 0.542,0.302 10 false G218 2.01,1.354 2.552,1.656 0.542,0.302 10 false G218
*A Main Body ECU (Multiplex Network Body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


E373865C01
2.063,3.104 2.583,3.344 0.521,0.24 4.479,3.125 5,3.365 0.521,0.24 5.229,4.615 5.75,4.854 0.521,0.24 6.24,4.604 6.76,4.844 0.521,0.24 3.656,4.615 4.177,4.854 0.521,0.24 1.344,4.656 1.865,4.896 0.521,0.24 1.521,6.177 2.042,6.417 0.521,0.24 4.625,6.198 5.146,6.438 0.521,0.24 3.271,7.833 3.792,8.073 0.521,0.24 1.354,4.344 1.875,4.583 0.521,0.24 1.615,1.833 1.938,1.833 true 1.625,1.49 1.948,1.49 true 0.625,1.292 0.948,1.292 true 1.594,0.635 1.594,0.406 1.594,0.406 1.802,0.406 false 0.146,0.115 0.458,0.313 0.313,0.198 12 false *A 0.24,1.208 0.604,1.646 0.365,0.438 10 false 2Q*B 2P*C 2,1.396 2.438,1.844 0.438,0.448 10 false G218 1.99,1.74 2.448,2.208 0.458,0.469 10 false G216 3.479,7.875 3.635,8.073 0.156,0.198 10 false A 4.573,3.146 4.938,3.583 0.365,0.438 10 false G218 2.167,3.125 2.531,3.563 0.365,0.438 10 false G216 1.865,0.292 2.177,0.49 0.313,0.198 10 false *1 0.854,1.802 1.219,2.24 0.365,0.438 10 false 2M 3.813,4.635 4.177,5.073 0.365,0.438 10 false 2M 5.406,4.635 5.771,5.073 0.365,0.438 10 false 2K 0.885,2.219 1.25,2.656 0.365,0.438 10 false 2K 0.917,2.448 1.281,2.885 0.365,0.438 10 false 2L 6.417,4.635 6.781,5.073 0.365,0.438 10 false 2L 1.521,4.365 1.885,4.802 0.365,0.438 10 false 2Q 1.927,4.365 2.292,4.802 0.365,0.438 10 false *B 1.521,4.688 1.885,5.125 0.365,0.438 10 false 2P 1.938,4.677 2.302,5.115 0.365,0.438 10 false *C 5.844,1.073 6.281,1.521 0.438,0.448 10 false 2N 1.677,6.198 2.115,6.646 0.438,0.448 10 false 2N 5.844,1.708 6.281,2.156 0.438,0.448 10 false 2O 4.792,6.219 5.229,6.667 0.438,0.448 10 false 2O
*A Main Body ECU (Multiplex Network Body ECU) with 2 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) - -


a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
A-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
A-31 (BECU) - Body ground Input - Battery power supply (for CPU) Always 11 to 14 V -
G218-6 (FLCY) - Body ground Input R - Body ground Front door LH courtesy light switch input Front door LH closed → open 10 kΩ or higher → Below 1 Ω FL Door Courtesy SW
G218-27 (FRCY) - Body ground Input B - Body ground Front door RH courtesy light switch input Front door RH closed → open 10 kΩ or higher → Below 1 Ω FR Door Courtesy SW
A-13 (LCTY) - Body ground Input - Rear door LH courtesy light switch input Rear door LH closed → open 10 kΩ or higher → Below 1 Ω RL Door Courtesy SW
A-2 (RCTY) - Body ground Input - Rear door RH courtesy light switch input Rear door RH closed → open 10 kΩ or higher → Below 1 Ω RR Door Courtesy SW
A-4 (BCTY) - Body ground Input - Back door courtesy light switch input Back door closed → open 10 kΩ or higher → Below 1 Ω Back Door Courtesy SW
G216-27 (GCTY) - Body ground* Input V - Body ground Glass hatch courtesy switch input Glass hatch closed → open 10 kΩ or higher → Below 1 Ω Glass Hatch Courtesy SW

*: w/ Glass Hatch Opener System



c.

Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item

*1: for 5 Door

*2: for LHD

*3: for RHD

*4: w/ Glass Hatch Opener System

2N-12 (LSFL) - Body ground Input G - Body ground Front door LH unlock detection switch input Front door LH locked → unlocked Pulse generation
(See waveform 1)
FL Door Lock Pos
2O-41 (LSFR) - Body ground Input G - Body ground Front door RH unlock detection switch input Front door RH locked → unlocked Pulse generation
(See waveform 1)
FR Door Lock Pos
2Q-26 (LSWL) - Body ground*1, *2 Input B - Body ground Rear door LH unlock detection switch input Rear door LH locked → unlocked Pulse generation
(See waveform 1)
RL-Door Lock Pos SW
2O-38 (LSWL) - Body ground*1, *3 Input B - Body ground Rear door LH unlock detection switch input Rear door LH locked → unlocked Pulse generation
(See waveform 1)
RL-Door Lock Pos SW
G216-2 (LSWR) - Body ground*1 Input V - Body ground Rear door RH unlock detection switch input Rear door RH locked → unlocked Pulse generation
(See waveform 1)
RR-Door Lock Pos SW
G218-17 (LSWB) - Body ground Input SB - Body ground Back door unlock detection switch input Back door locked → unlocked Pulse generation
(See waveform 1)
Back Door Lock Pos SW
G218-6 (FLCY) - Body ground Input R - Body ground Front door LH courtesy light switch input Front door LH closed → open Pulse generation
(See waveform 2)
FL Door Courtesy SW
G218-27 (FRCY) - Body ground Input B - Body ground Front door RH courtesy light switch input Front door RH closed → open Pulse generation
(See waveform 2)
FR Door Courtesy SW
2Q-33 (LCTY) - Body ground*1, *2 Input V - Body ground Rear door LH courtesy light switch input Rear door LH closed → open Pulse generation
(See waveform 2)
RL Door Courtesy SW
2O-15 (LCTY) - Body ground*1, *3 Input V - Body ground Rear door LH courtesy light switch input Rear door LH closed → open Pulse generation
(See waveform 2)
RL Door Courtesy SW
2N-30 (RCTY) - Body ground*1, *2 Input R - Body ground Rear door RH courtesy light switch input Rear door RH closed → open Pulse generation
(See waveform 2)
RR Door Courtesy SW
2P-23 (RCTY) - Body ground*1, *3 Input R - Body ground Rear door RH courtesy light switch input Rear door RH closed → open Pulse generation
(See waveform 2)
RR Door Courtesy SW
2Q-27 (BCTY) - Body ground*2 Input G - Body ground Back door courtesy light switch input Back door closed → opened Pulse generation
(See waveform 2)
Back Door Courtesy SW
2N-27 (BCTY) - Body ground*3 Input G - Body ground Back door courtesy light switch input Back door closed → opened Pulse generation
(See waveform 2)
Back Door Courtesy SW
G216-27 (GCTY) - Body ground*4 Input V - Body ground Glass hatch courtesy light switch input Glass hatch closed → opened Pulse generation
(See waveform 2)
Glass Hatch Courtesy Switch
G216-28 (GOSW) - Body ground*4 Input LG - Body ground Glass hatch opener switch assembly signal input Glass hatch opener switch assembly on → off Below 1 V → 11 to 14 V Glass Hatch Opener Switch
2M-30 (BZR) - Body ground Output GR - Body ground Wireless buzzer signal output Procedure:
1.

Engine switch off

2.

All doors closed

3.

Lock switch of electrical key transmitter sub-assembly not pressed → pressed


Below 1 V → pulse generation -


e.
B340769C02
0.219,1.583 0.552,1.75 0.333,0.167 10 false GND 1.25,1.917 1.5,2.083 0.25,0.167 10 false *a 2.219,1.917 2.469,2.083 0.25,0.167 10 false *b
*a Door locked
*b Door unlocked


Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content

*1: for LHD

*2: for RHD

Tester Connection 2N-12 (LSFL) - Body ground
2O-41 (LSFR) - Body ground
2Q-26 (LSWL) - Body ground*1
2O-38 (LSWL) - Body ground*2
G216-2 (LSWR) - Body ground
G218-17 (LSWB) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Door locked → unlocked


f.
B340769C03
0.219,1.583 0.552,1.75 0.333,0.167 10 false GND 1.25,1.917 1.5,2.083 0.25,0.167 10 false *a 2.219,1.917 2.469,2.083 0.25,0.167 10 false *b
*a Door closed
*b Door open


Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content

*1: for LHD

*2: for RHD

Tester Connection G218-6 (FLCY) - Body ground
G218-27 (FRCY) - Body ground
2Q-33 (LCTY) - Body ground*1
2O-15 (LCTY) - Body ground*2
2N-30 (RCTY) - Body ground*1
2P-23 (RCTY) - Body ground*2
2Q-27 (BCTY) - Body ground*1
2N-27 (BCTY) - Body ground*2
G216-27 (GCTY) - Body ground
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Door closed → opened