Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › from 2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

Driver side junction block assembly

·

Certification ECU (smart key ECU assembly)

·

Harness or connector


DTC Output Confirmation Operation:

Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2274
Power Source Control
·

ACC Relay Monitor



WIRING DIAGRAM

B492207E01
4.417,1.771 6.854,1.969 2.438,0.198 10 false Driver Side Junction Block Assembly 1.406,0.771 2.177,0.969 0.771,0.198 10 false SMART 0.115,0.583 1.198,0.781 1.083,0.198 10 false from Battery 2.01,1.927 3.552,2.281 1.542,0.354 10 false Certification ECU (Smart Key ECU Assembly) 2,1.75 2.615,1.948 0.615,0.198 10 false G215 2.292,0.604 2.604,0.802 0.313,0.198 10 false +B 2.313,1.25 2.625,1.448 0.313,0.198 10 false E 2.604,0.969 3.052,1.167 0.448,0.198 10 false ACCD 3.115,0.885 3.271,1.083 0.156,0.198 10 false 9 2.01,0.5 2.323,0.698 0.313,0.198 10 false 10 2.021,1.146 2.333,1.344 0.313,0.198 10 false 11 4.344,0.573 4.656,0.771 0.313,0.198 10 false 2K 4.354,0.99 4.667,1.188 0.313,0.198 10 false 2O 6.479,0.573 6.792,0.771 0.313,0.198 10 false 2O 6.49,0.99 6.802,1.188 0.313,0.198 10 false 2N 5.042,1.302 5.5,1.5 0.458,0.198 10 false ACC 5.802,0.719 6.26,0.917 0.458,0.198 10 false ACC 4.385,0.375 4.542,0.573 0.156,0.198 10 false 1 4.354,0.792 4.667,0.99 0.313,0.198 10 false 23 6.479,0.375 6.792,0.573 0.313,0.198 10 false 50 6.51,0.792 6.667,0.99 0.156,0.198 10 false 1 3.177,0.552 4.26,0.75 1.083,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
C277841C37
1.417,0.094 1.802,0.323 0.385,0.229 0.99,1.698 0.99,0.813 true 0.104,0.052 0.302,0.219 0.198,0.167 10 false *a 0.865,1.74 1.26,1.885 0.396,0.146 10 false ACCD 1.438,0.125 1.906,0.323 0.469,0.198 10 false G215
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Install the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G215-9 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), POWER SUPPLY AND BODY GROUND)
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2O, 2K and 2N driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-9 (ACCD) - 2O-23 Always Below 1 Ω
2N-1 - Body ground Always Below 1 Ω
G215-9 (ACCD) or 2O-23 - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2K-1 - Body ground Always 11 to 14 V



e.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Reconnect the all driver side junction block assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

B492526C01
3.021,0.896 3.354,1.083 0.333,0.188 4.573,0.896 4.906,1.083 0.333,0.188 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 3.094,0.906 3.427,1.083 0.333,0.177 10 false 2A 4.635,0.906 4.969,1.083 0.333,0.177 10 false 2D
*a Component with harness connected
(Driver Side Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
2O-50 - Body ground Engine switch on (ACC) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY