Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Viscous Heater with Magnet Clutch Circuit  


DESCRIPTION

When the idle up switch assembly is pushed, the air conditioning amplifier assembly turns on the viscous heater relay and operates the viscous heater. If the viscous heater does not operate when the idle up switch assembly is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E374399E01
5.427,1.208 7.021,1.625 1.594,0.417 10 false Air Conditioning Amplifier Assembly 5.417,1.042 5.875,1.24 0.458,0.198 10 false G25 4.521,0.552 4.979,0.75 0.458,0.198 10 false 1T 4.51,0.292 4.969,0.49 0.458,0.198 10 false 11 4.521,1.094 4.979,1.292 0.458,0.198 10 false 1T 4.542,0.844 5,1.042 0.458,0.198 10 false 12 2.521,1.094 2.979,1.292 0.458,0.198 10 false 1S 2.552,0.854 3.01,1.052 0.458,0.198 10 false 1 2.521,0.552 2.979,0.75 0.458,0.198 10 false 1T 2.563,0.302 3.021,0.5 0.458,0.198 10 false 8 2.031,0.698 2.49,0.896 0.458,0.198 10 false IG1 2.896,1.25 3.625,1.438 0.729,0.188 10 false VISC HTR 3.625,1.469 4.354,1.656 0.729,0.188 10 false VISC HTR 2.073,1.781 5.104,2.156 3.031,0.375 10 false Engine Room No. 1 Relay Block, Junction Block 0.219,0.531 1.573,0.781 1.354,0.25 10 false from IG1 NO.1 Relay 0.729,1.063 2.083,1.313 1.354,0.25 10 false from Battery 1.969,3 2.427,3.198 0.458,0.198 10 false C94 1.979,3.177 5,3.625 3.021,0.448 10 false Viscous Heater with Magnet Clutch Assembly*1 1.802,4.427 5.083,4.74 3.281,0.313 10 false Viscous Heater with Magnet Clutch Assembly*2 1.802,4.25 2.26,4.448 0.458,0.198 10 false r4 3.604,2.458 4.063,2.656 0.458,0.198 10 false 1 3.625,3.719 4.083,3.917 0.458,0.198 10 false 1 3.167,3.833 3.625,4.031 0.458,0.198 10 false MG+ 0.094,4.073 1.25,4.302 1.156,0.229 10 false *1: for 1KD-FTV 0.104,4.406 1.26,4.635 1.156,0.229 10 false *2: for 1GD-FTV 5.885,0.521 6.344,0.719 0.458,0.198 10 false MG+ 5.594,0.438 6.052,0.635 0.458,0.198 10 false 16

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (VISCOUS HEATER)
a.

Select the Active Test, use the GTS to generate a control command, and then check that the viscous heater with magnet clutch assembly operates (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Viscous Heater Viscous heater operation ON or OFF -

OK:

The display is as specified in the normal condition column.




OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)
2.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)
a.
E378404E01
0.667,0.469 1.167,0.719 0.5,0.25 0.417,1.5 0.917,1.75 0.5,0.25 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a 0.844,0.5 1.156,0.698 0.313,0.198 10 false 1S 0.625,1.542 0.938,1.74 0.313,0.198 10 false 1T

Disconnect the 1S and 1T engine room No. 1 relay block, junction block connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1S-1 - Body ground Always 11 to 14 V
1T-8 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Engine Room No. 1 Relay Block, Junction Block)



OK

3.INSPECT VISCOUS HEATER RELAY (VISC HTR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT VISCOUS HEATER RELAY (VISC HTR)
a.

Remove the viscous heater relay (VISC HTR).


b.

Result
Result Proceed to
OK (for 1KD-FTV) A
OK (for 1GD-FTV) B
NG C


A

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)

C

REPLACE ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)
a.

Disconnect the 1T engine room No. 1 relay block, junction block connector.


b.

Disconnect the C94 viscous heater with magnet clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1T-12 - C94-1 Always Below 1 Ω
1T-12 - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the 1T engine room No. 1 relay block, junction block connector.


b.

Disconnect the G25 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1T-11 - G25-16 (MG+) Always Below 1 Ω
1T-11 - Body ground Always 10 kΩ or higher




OK

6.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY
a.

Remove the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>REMOVAL).


b.

Inspect the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH(for 1KD-FTV)>INSPECTION).



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY)
a.

Disconnect the 1T engine room No. 1 relay block, junction block connector.


b.

Disconnect the r4 viscous heater with magnet clutch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1T-12 - r4-1 Always Below 1 Ω
1T-12 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the 1T engine room No. 1 relay block, junction block connector.


b.

Disconnect the G25 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1T-11 - G25-16 (MG+) Always Below 1 Ω
1T-11 - Body ground Always 10 kΩ or higher




OK

9.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY
a.

Remove the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>REMOVAL).


b.

Inspect the viscous heater with magnet clutch assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>VISCOUS HEATER MAGNET CLUTCH (for 1GD-FTV)>INSPECTION).



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY