Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053721 NAVIGATION / MULTI INFO DISPLAY _0260991 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B1324  Lost Communication with Meter  


DESCRIPTION

This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.

DTC No. DTC Detection Condition Trouble Area
B1324 After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the engine switch is on (ACC) 1 or more times, the navigation receiver assembly does not receive the signal for 30 seconds or more.
·

Combination meter assembly

·

Navigation receiver assembly

·

Harness or connector



WIRING DIAGRAM

E377430E02
1.594,0.417 2.208,0.615 0.615,0.198 10 false MSCH 1.615,1.052 2.229,1.25 0.615,0.198 10 false MSCL 5.094,0.406 5.708,0.604 0.615,0.198 10 false CNH1 5.104,1.052 5.719,1.25 0.615,0.198 10 false CNL1 2.135,0.26 2.448,0.458 0.313,0.198 10 false 38 2.135,0.927 2.448,1.125 0.313,0.198 10 false 37 4.833,0.271 4.99,0.469 0.156,0.198 10 false 3 4.833,0.927 4.99,1.125 0.156,0.198 10 false 4 0.844,1.604 1.458,1.802 0.615,0.198 10 false G304 0.844,1.802 2.969,2.021 2.125,0.219 10 false Combination Meter Assembly 4.729,1.615 5.344,1.813 0.615,0.198 10 false H55 4.729,1.792 6.917,2.167 2.188,0.375 10 false Navigation Receiver Assembly 0.948,2.24 3.229,2.438 2.281,0.198 10 false : Local Bus Communication Line

CAUTION / NOTICE / HINT

HINT:

When replacing the navigation receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H55 navigation receiver assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H55-3 (CNH1) - G304-38 (MSCH) Always Below 1 Ω
H55-4 (CNL1) - G304-37 (MSCL) Always Below 1 Ω
H55-3 (CNH1) - Body ground Always 10 kΩ or higher
H55-4 (CNL1) - Body ground Always 10 kΩ or higher
H55-3 (CNH1) - H55-4 (CNL1) Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H55-3 (CNH1) - Body ground Always Below 1 V
H55-4 (CNL1) - Body ground Always Below 1 V




OK

2.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT COMBINATION METER ASSEMBLY
a.

Remove the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.
E317642E09
0.583,1.792 0.729,1.792 0.729,1.792 0.906,1.313 true 1.292,1.792 1.167,1.792 1.167,1.792 1.052,1.313 true 1.365,1.708 1.979,1.906 0.615,0.198 10 false MSCL 0.115,1.719 0.729,1.917 0.615,0.198 10 false MSCH

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
38 (MSCH) - 37 (MSCL) Always 108 to 132 Ω




OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT NAVIGATION RECEIVER ASSEMBLY

b.
E335243E01
1.342,1.736 1.752,1.904 0.410,0.168 10 CNL1 2.724,1.736 3.134,1.904 0.410,0.168 10 CNH1 1.823,1.831 1.924,1.831 1.924,1.831 2.107,1.086 false 2.663,1.831 2.562,1.831 2.562,1.831 2.379,1.086 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CNH1) - 4 (CNL1) Always 108 to 132 Ω




OK

4.CHECK COMBINATION METER ASSEMBLY

NG

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.




OK

5.CHECK METER / GAUGE SYSTEM

NG

5.CHECK METER / GAUGE SYSTEM
a.

Turn the engine switch on (IG) and wait 30 seconds.


b.

Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.

OK:

Audio system returns to normal.




OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG