Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM › from 2017.08
RM27T0E _55 Steering _053718 STEERING COLUMN _0260954 STEERING LOCK SYSTEM J

STEERING COLUMN  STEERING LOCK SYSTEM  Unable to Unlock Steering Wheel (Engine cannot Start)  


DESCRIPTION

The steering lock ECU (steering lock actuator or upper bracket assembly) activates the steering lock motor and moves the lock bar into the steering column to lock the steering.

The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the engine switch is turned on (IG) while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
·

Unlock Request Receive

·

S Code Check

·

L Code Check

·

Steering Unlock



WIRING DIAGRAM

C382197E03
0.885,1.802 1.229,2 0.344,0.198 10 false LIN1 5.375,1.823 5.646,2 0.271,0.177 10 false LIN 2.396,2.417 2.667,2.594 0.271,0.177 10 false LIN 2.281,2.917 2.677,3.094 0.396,0.177 10 false SLR+ 2.354,3.344 2.667,3.531 0.313,0.188 10 false SLP 2.51,3.979 2.667,4.167 0.156,0.188 10 false E 5.365,2.896 5.677,3.083 0.313,0.188 10 false IGE 5.365,3.344 5.771,3.51 0.406,0.167 10 false SLP1 5.365,3.979 5.729,4.167 0.365,0.188 10 false GND 5.375,0.333 5.646,0.51 0.271,0.177 10 false B 3.063,0.323 3.885,0.531 0.823,0.208 10 false from Battery 4.333,0.51 5.208,0.708 0.875,0.198 10 false STRG LOCK 0.188,2.656 0.625,2.844 0.438,0.188 10 false G207 0.188,2.813 1.771,3.156 1.583,0.344 10 false ID Code Box (Immobiliser Code ECU) 1.635,4.406 2.063,4.583 0.427,0.177 10 false G215 0.698,5.281 2.354,5.479 1.656,0.198 10 false : LIN Communication Line 1.625,4.573 3.458,4.938 1.833,0.365 10 false Certification ECU (Smart Key ECU Assembly) 5.281,4.479 5.625,4.677 0.344,0.198 10 false G35 5.271,4.635 7.063,5.375 1.792,0.74 10 false Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) 1.281,1.635 1.438,1.833 0.156,0.198 10 false 2 2.75,2.24 2.906,2.438 0.156,0.198 10 false 6 2.75,2.792 2.958,2.969 0.208,0.177 10 false 24 2.75,3.229 2.958,3.406 0.208,0.177 10 false 23 2.74,3.854 2.948,4.031 0.208,0.177 10 false 11 5.146,0.208 5.302,0.375 0.156,0.167 10 false 7 5.156,1.635 5.313,1.802 0.156,0.167 10 false 5 5.146,2.781 5.302,2.948 0.156,0.167 10 false 3 5.156,3.208 5.313,3.375 0.156,0.167 10 false 4 5.156,3.854 5.313,4.021 0.156,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), refer to the Service Bulletin.



PROCEDURE

1.CHECK POWER SOURCE MODE CHANGING FUNCTION (SWITCH CONDITION)
a.

Check the power source mode change.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

OK:

The power source mode changes to on (IG).



Result:
Proceed to
OK (w/ Multi-information Display (TFT Display Type))
OK (w/ Multi-information Display (Segment Display Type))
NG



OK (w/ Multi-information Display (Segment Display Type))

2.CHECK INDICATOR

OK (w/ Multi-information Display (TFT Display Type))

3.CHECK INDICATOR

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

2.CHECK INDICATOR
a.

With the engine switch on (IG), check that the entry warning light on the combination meter assembly is illuminated green.


Result:
Result Proceed to
Entry warning light illuminated green. A
Entry warning light not illuminated green. B



A

4.CHECK STEERING UNLOCK

B

5.CHECK FOR DTC
3.CHECK INDICATOR
a.

With the engine switch on (IG), check that push engine switch while turning steering wheel in either direction is displayed on the multi-information display in the combination meter assembly.


Result:
Result Proceed to
Push engine switch while turning steering wheel in either direction is displayed. A
Push engine switch while turning steering wheel in either direction is not displayed. B



A

4.CHECK STEERING UNLOCK

B

5.CHECK FOR DTC
4.CHECK STEERING UNLOCK
a.

Turn the steering wheel left and right, and then press the engine switch.


b.

Check that the steering is unlocked.


Result:
Result Proceed to
The steering is unlocked. A
The steering is not unlocked. B



A

END (STEERING LOCK IS NORMAL)

B

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Check for DTCs and note any DTCs that are output.

Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

6.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)

B

6.READ VALUE USING GTS (UNLOCK REQUEST RECEIVE)
a.

Enter the following menus: Body Electrical / Entry&Start / Data List.


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Unlock request signal received state OK or NG OK: Unlock request signal received within 10 seconds of engine switch on (IG) or on (ACC), or of an engine start operation being performed
NG: Engine switch not turned on (IG) or on (ACC), and engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (S CODE CHECK)

NG

15.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
7.READ VALUE USING GTS (S CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (L CODE CHECK)

NG

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
8.READ VALUE USING GTS (L CODE CHECK)
a.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator or upper bracket assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - POWER SUPPLY AND BODY GROUND)

NG

13.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - POWER SUPPLY AND BODY GROUND)
a.
C350526C51
1.5,0.917 1.927,1.156 0.427,0.24 0.917,1.813 1.25,2.427 true 2.531,1.813 2.198,2.427 true 0.188,0.135 0.5,0.292 0.313,0.156 10 false *a 1.594,0.948 1.969,1.219 0.375,0.271 10 false G35 0.729,1.604 1.094,1.802 0.365,0.198 10 false GND 2.5,1.615 2.76,1.823 0.26,0.208 10 false B
*a Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Disconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

10.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (MOTOR ACTIVATION COMMAND SIGNAL)
a.

Reconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.
C380739C05
0.344,2.885 1.698,3.052 1.354,0.167 1.573,4.042 2.417,4.208 0.844,0.167 2.313,2.948 2.719,3.083 0.406,0.135 0.177,0.917 0.563,1.125 0.385,0.208 1.042,1.906 1.896,1.104 true 2.844,2 2.292,1.094 true 2.573,2.938 3,2.594 3,2.594 1.615,2.875 true 2.073,4.417 2.073,4.208 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.25,0.938 0.594,1.146 0.344,0.208 10 false G35 0.885,1.99 1.25,2.208 0.365,0.219 10 false IGE 2.74,2.031 3.135,2.24 0.396,0.208 10 false GND 3.073,2.51 3.323,2.74 0.25,0.229 10 false *b 3.031,4.042 3.396,4.292 0.365,0.25 10 false GND 1.99,4.469 2.188,4.667 0.198,0.198 10 false *c 0.198,2.323 0.51,2.521 0.313,0.198 10 false *d
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))
*b Steering Lock Motor not Operating
*c Steering Lock Motor Operating
*d Waveform


Using an oscilloscope, check the waveform.

OK:
Item Content
Tester Connection G35-3 (IGE) - G35-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Any door opened when conditions below met, and then steering lock motor activated:
·

Shift lever in P*

·

Steering lock unlocked in advance by carrying electrical key transmitter sub-assembly and turning engine switch on (IG)

·

After above conditions met, engine switch turned off


Specified Condition Pulse generation
(See waveform)


*: for Automatic Transmission


HINT:
·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).

-

To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.

*: for Automatic Transmission






Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
a.

Disconnect the G35 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-3 (IGE) - G215-24 (SLR+) Always Below 1 Ω
G35-3 (IGE) or G215-24 (SLR+) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C350527C72
0.427,0.823 0.844,1.083 0.417,0.26 2.583,2.75 1.865,1.979 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.542,2.802 3.052,3.063 0.51,0.26 10 false IGE 0.51,0.865 0.823,1.021 0.313,0.156 10 false G35
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Reconnect the steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

13.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

for Power Tilt and Power Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY

for Manual Tilt and Manual Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to the Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between ID code box (immobiliser code ECU) and steering lock ECU (steering lock actuator or upper bracket assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is not registered, or the ID code box (immobiliser code ECU) or steering lock ECU (steering lock actuator or upper bracket assembly) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one and perform registration again.

HINT:

Refer to the Service Bulletin.



b.

Perform registration.

HINT:

Refer to the Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
S Code Check Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered, or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.

·

The steering cannot be locked.

·

The steering cannot be unlocked (the engine cannot be started).



OK:

"OK" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

15.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.
C350527C73
1.51,0.875 1.927,1.135 0.417,0.26 2.552,2.74 1.719,1.948 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.469,2.771 2.906,3.063 0.438,0.292 10 false SLP1 1.594,0.906 1.906,1.146 0.313,0.24 10 false G35
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G35-4 (SLP1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.READ VALUE USING GTS (STEERING UNLOCK)

NG

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
16.READ VALUE USING GTS (STEERING UNLOCK)
a.

Check that the steering is locked.


b.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Steering lock ECU (steering lock actuator or upper bracket assembly) unlock confirmation status Unset or Set Unset: Unlock not confirmed
Set: Unlock confirmed
When Unset is displayed, the steering is not unlocked (the engine cannot be started).

OK:

"Set" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



b.

Perform registration.

HINT:

Refer to the Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Unlock request signal received state OK or NG OK: Unlock request signal received within 10 seconds of engine switch on (IG) or on (ACC), or of an engine start operation being performed
NG: Engine switch not turned on (IG) or on (ACC), and engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
a.

Disconnect the G35 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G35-4 (SLP1) - G215-23 (SLP) Always Below 1 Ω
G35-4 (SLP1) or G215-23 (SLP) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
a.

Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.

for Power Tilt and Power Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>DISASSEMBLY

for Manual Tilt and Manual Telescopic Steering Column:

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>DISASSEMBLY


b.

Perform registration.

HINT:

Refer to the Service Bulletin.



c.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Unlock Request Receive Unlock request signal received state OK or NG OK: Unlock request signal received within 10 seconds of engine switch on (IG) or on (ACC), or of an engine start operation being performed
NG: Engine switch not turned on (IG) or on (ACC), and engine start operation not performed
·

The engine cannot be started when an unlock request signal cannot be received.

·

If OK is not displayed even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.



OK:

Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)