Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

When the engine switch cannot be turned on (ACC) or on (IG), there may be a malfunction in interior certification, or the ACC relay or IG relay system. If interior certification does not succeed, the certification ECU (smart key ECU assembly) may be malfunctioning, or communication may not be possible between the No. 1 indoor electrical key antenna assembly (front floor), No. 2 indoor electrical key antenna assembly (rear floor) or No. 3 indoor electrical key antenna assembly (inside luggage), the electrical key transmitter sub-assembly, and the door control receiver.

When the electrical key transmitter sub-assembly is brought into the cabin, the key ID code sent from the electrical key transmitter sub-assembly and the key ID code stored in the certification ECU (smart key ECU assembly) are certified. If these codes do not match and certification fails, the engine switch cannot be turned on (ACC) or on (IG).

When the door is unlocked and the electrical key transmitter sub-assembly is brought into the cabin, the certification ECU (smart key ECU assembly) activates the indoor electrical key antenna and forms a detection area. When the electrical key transmitter sub-assembly is recognized inside the detection area, it returns the key ID code. This is received by the door control receiver, which then sends it to the certification ECU (smart key ECU assembly).

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

IG Relay Monitor (Inside)

·

ACC Relay Monitor

·

IG Relay Monitor (Outside)

·

Latch Circuit

·

Power Supply Condition



WIRING DIAGRAM

B492216E01
0.083,8.063 6.5,8.26 6.417,0.198 10 false Certification ECU (Smart Key ECU Assembly) 3.135,7.125 6,7.604 2.865,0.479 10 false Driver Side Junction Block Assembly 3.74,6.865 4.49,7.167 0.75,0.302 10 false IG NO. 5 4.948,6.354 5.698,6.656 0.75,0.302 10 false WASHER 4.854,5.313 5.802,5.729 0.948,0.417 10 false ECU-IG NO. 3 3.74,5.688 4.49,5.99 0.75,0.302 10 false IG NO. 4 3.75,4.604 4.5,4.906 0.75,0.302 10 false IG NO. 3 5.156,4.24 5.635,4.656 0.479,0.417 10 false 4WD 3.74,3.521 4.49,3.823 0.75,0.302 10 false IG NO. 1 4.896,3.188 5.927,3.583 1.031,0.396 10 false ECU-IG NO. 1 3.896,2.427 4.646,2.729 0.75,0.302 10 false ACC 5.135,1.875 5.885,2.177 0.75,0.302 10 false ACC 0.906,0.385 1.24,0.708 0.333,0.323 10 false +B 3.26,0.521 3.833,0.802 0.573,0.281 10 false SMART 4.406,0.354 5.448,0.667 1.042,0.313 10 false from Battery 0.927,0.969 1.26,1.292 0.333,0.323 10 false E 1.167,0.969 1.688,1.281 0.521,0.313 10 false G215 1.25,0.771 1.583,1.094 0.333,0.323 10 false 11 1.188,0.375 1.656,0.708 0.469,0.333 10 false G215 1.24,0.167 1.573,0.49 0.333,0.323 10 false 10 1.167,3.25 1.708,3.458 0.542,0.208 10 false G213 1.271,3.021 1.604,3.344 0.333,0.323 10 false 3 1.167,2.167 1.708,2.406 0.542,0.24 10 false G215 1.302,1.927 1.635,2.25 0.333,0.323 10 false 9 0.74,2.167 1.281,2.51 0.542,0.344 10 false ACCD 0.792,3.281 1.333,3.625 0.542,0.344 10 false IG1D 2.854,2.156 3.188,2.479 0.333,0.323 10 false 2O 2.813,3.26 3.146,3.583 0.333,0.323 10 false 2O 2.833,3.073 3.167,3.396 0.333,0.323 10 false 22 2.865,1.969 3.198,2.292 0.333,0.323 10 false 23 2.813,1.698 3.146,2.021 0.333,0.323 10 false 2K 2.885,1.51 3.219,1.833 0.333,0.323 10 false 1 6.021,6.594 6.354,6.917 0.333,0.323 10 false 2N 6.031,6.396 6.365,6.719 0.333,0.323 10 false 1 6.042,3.01 6.375,3.333 0.333,0.323 10 false 2M 6.052,2.802 6.385,3.125 0.333,0.323 10 false 13 6.01,4.052 6.344,4.375 0.333,0.323 10 false 2O 6.031,3.854 6.365,4.177 0.333,0.323 10 false 12 6.042,5.135 6.375,5.458 0.333,0.323 10 false 2N 6.052,4.938 6.385,5.26 0.333,0.323 10 false 23 6.042,6.167 6.375,6.49 0.333,0.323 10 false 2M 6.052,5.99 6.385,6.313 0.333,0.323 10 false 6 6.031,1.708 6.365,2.031 0.333,0.323 10 false 2O 6.01,1.49 6.344,1.813 0.333,0.323 10 false 50 1.604,1.677 2.646,1.99 1.042,0.313 10 false from Battery

B492217E01
0.188,8.188 6.604,8.385 6.417,0.198 10 false Certification ECU (Smart Key ECU Assembly) 0.781,0.74 1.198,0.99 0.417,0.25 10 false STP1 1.188,0.74 1.604,0.99 0.417,0.25 10 false G213 1.302,0.542 1.719,0.792 0.417,0.25 10 false 2 3.469,0.74 3.885,0.99 0.417,0.25 10 false L 3.188,0.625 3.604,0.875 0.417,0.25 10 false 3 3.01,1.281 5,1.656 1.99,0.375 10 false Stop Light Switch Assembly 4.115,0.563 4.531,0.813 0.417,0.25 10 false B 3.938,0.875 4.354,1.125 0.417,0.25 10 false GND 3.031,1.125 3.448,1.375 0.417,0.25 10 false A99 4.333,0.427 4.75,0.677 0.417,0.25 10 false 7 4.344,0.75 4.76,1 0.417,0.25 10 false 2 4.563,0.719 4.979,0.969 0.417,0.25 10 false STOP 5.604,0.563 6.719,0.865 1.115,0.302 10 false from Battery 0.719,1.906 1.333,2.104 0.615,0.198 10 false SSW1 0.719,2.344 1.333,2.542 0.615,0.198 10 false SSW2 0.708,2.729 1.323,2.927 0.615,0.198 10 false AGND 3.438,1.948 4.052,2.146 0.615,0.198 10 false SS1 3.427,2.333 4.042,2.531 0.615,0.198 10 false SS2 3.469,2.75 4.083,2.948 0.615,0.198 10 false AGND 3.354,3.156 5.344,3.531 1.99,0.375 10 false Engine Switch 3.354,3.021 3.771,3.271 0.417,0.25 10 false G206 1.177,1.917 1.594,2.167 0.417,0.25 10 false G215 1.198,2.354 1.615,2.604 0.417,0.25 10 false G215 1.188,2.729 1.604,2.979 0.417,0.25 10 false G215 1.271,1.698 1.688,1.948 0.417,0.25 10 false 16 1.25,2.125 1.667,2.375 0.417,0.25 10 false 18 1.271,2.552 1.688,2.802 0.417,0.25 10 false 12 1.156,3.677 1.573,3.927 0.417,0.25 10 false G215 1.198,4.219 1.615,4.469 0.417,0.25 10 false G215 1.292,4 1.708,4.25 0.417,0.25 10 false 20 1.302,3.458 1.719,3.708 0.417,0.25 10 false 21 0.75,3.667 1.167,3.917 0.417,0.25 10 false CLG5 0.74,4.229 1.156,4.479 0.417,0.25 10 false CG5B 3.438,3.677 3.854,3.927 0.417,0.25 10 false CLG 3.458,4.25 3.875,4.5 0.417,0.25 10 false CLGB 3.458,5.219 3.875,5.469 0.417,0.25 10 false CLG 3.448,5.771 3.865,6.021 0.417,0.25 10 false CLGB 0.75,5.177 1.167,5.427 0.417,0.25 10 false CLG6 0.729,5.75 1.146,6 0.417,0.25 10 false CG6B 1.188,5.198 1.604,5.448 0.417,0.25 10 false G214 1.167,5.76 1.583,6.01 0.417,0.25 10 false G214 1.26,5 1.677,5.25 0.417,0.25 10 false 15 1.271,5.531 1.688,5.781 0.417,0.25 10 false 14 0.75,6.729 1.167,6.979 0.417,0.25 10 false CLG7 0.74,7.292 1.156,7.542 0.417,0.25 10 false CG7B 1.198,6.729 1.615,6.979 0.417,0.25 10 false G214 1.198,7.271 1.615,7.521 0.417,0.25 10 false G214 1.26,6.51 1.677,6.76 0.417,0.25 10 false 4 1.292,7.042 1.708,7.292 0.417,0.25 10 false 3 2.896,4.625 6.656,5.083 3.76,0.458 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 2.906,4.469 3.323,4.719 0.417,0.25 10 false i1 2.813,6.229 6.573,6.688 3.76,0.458 10 false No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor) 2.802,6.094 3.74,6.344 0.938,0.25 10 false R14*1, s1*2 2.698,7.729 6.802,8.188 4.104,0.458 10 false No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage) 2.729,7.583 3.667,7.833 0.938,0.25 10 false R15 3.875,8.229 4.813,8.479 0.938,0.25 10 false *1: for 3 Door 3.875,8.51 4.813,8.76 0.938,0.25 10 false *2: for 5 Door 3.229,1.802 3.646,2.052 0.417,0.25 10 false 5 3.219,2.188 3.635,2.438 0.417,0.25 10 false 1 3.188,2.635 3.604,2.885 0.417,0.25 10 false 6 3.229,3.552 3.635,3.813 0.406,0.26 10 false 1 3.229,4.083 3.635,4.344 0.406,0.26 10 false 3 3.208,5.083 3.615,5.344 0.406,0.26 10 false 1 3.198,5.625 3.604,5.885 0.406,0.26 10 false 2 3.208,6.604 3.615,6.865 0.406,0.26 10 false 1 3.198,7.135 3.604,7.396 0.406,0.26 10 false 2 3.438,6.771 3.854,7.021 0.417,0.25 10 false CLG 3.448,7.292 3.865,7.542 0.417,0.25 10 false CLGB

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to the Service Bulletin.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

An antenna coil is connected between the terminals of the indoor electrical key antenna.

·

The door control receiver is also involved in interior certification.



HINT:
·

If interior certification does not succeed, the History of Reason for Operation may remain in the certification ECU (smart key ECU assembly).

·

If the operation history remains, refer to the history table to determine the conditions and narrow down any trouble areas.



PROCEDURE

1.CHECK PUSH-BUTTON START FUNCTION
a.

Get into the vehicle while carrying the electrical key transmitter sub-assembly that has already been registered.


b.

for Automatic Transmission:

Shift lever in P.


c.

Check that the power source mode changes when the engine switch is pressed without depressing the brake pedal*1 or clutch pedal*2.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>OPERATION CHECK

*1: for Automatic Transmission

*2: for Manual Transmission



Result:
Result Proceed to
Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range for the front side A
Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range for the rear side B
Power source mode does not change when the electrical key transmitter sub-assembly is inside the push-button start function operation range for the inside luggage C
Power source mode does not change D



A

2.CHECK WAVE ENVIRONMENT

B

6.CHECK WAVE ENVIRONMENT

C

10.CHECK WAVE ENVIRONMENT

D

14.CHECK TRANSMITTER BATTERY
2.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform an entry and start system check.

NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The engine starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the engine switch is pressed with the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission) depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK KEY DIAGNOSTIC MODE
3.CHECK KEY DIAGNOSTIC MODE
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).


e.
B485492C01
0.573,1.125 2.417,0.25 2.417,0.25 2.75,0.25 false 1.896,1.104 2.417,0.25 false 2.792,0.167 3.104,0.365 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (front floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 1 indoor electrical key antenna assembly (front floor) is operating by the sounding of the buzzer.

·

When the wireless buzzer does not sound for No. 1 indoor electrical key antenna assembly (front floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 1 indoor electrical key antenna assembly (front floor), is malfunctioning.




Result:
Result Proceed to
The wireless buzzer sounds A
The wireless buzzer does not sound B



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the i1 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-21 (CLG5) - i1-1 (CLG) Always Below 1 Ω
G215-20 (CG5B) - i1-3 (CLGB) Always Below 1 Ω
G215-21 (CLG5) or i1-1 (CLG) - Body ground Always 10 kΩ or higher
G215-20 (CG5B) or i1-3 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the G215 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Using an oscilloscope, check the waveform.

B431370C60
1.625,0.49 2.01,0.729 0.385,0.24 1.417,2.083 1.604,1.615 false 2.25,2.083 2.031,1.615 false 0.448,0.271 0.76,0.427 0.313,0.156 10 false *a 3.604,0.271 3.917,0.427 0.313,0.156 10 false *b 4.75,1.969 5.063,2.125 0.313,0.156 10 false *c 5.552,1.979 5.865,2.135 0.313,0.156 10 false *d 1.708,0.521 2.042,0.729 0.333,0.208 10 false i1 2.104,2.125 2.833,2.406 0.729,0.281 10 false CLGB 3.99,1.292 4.302,1.448 0.313,0.156 10 false GND 1.219,2.125 1.958,2.406 0.74,0.281 10 false CLG
*a Front view of wire harness connector
(to No. 1 Indoor Electrical Key Antenna Assembly (Front Floor))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
i1-1 (CLG) - i1-3 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

6.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform an entry and start system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The engine starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the engine switch is pressed with the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission) depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

7.CHECK KEY DIAGNOSTIC MODE
7.CHECK KEY DIAGNOSTIC MODE
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).


e.
B485493C01
0.656,0.979 2.5,0.25 2.5,0.25 2.75,0.25 false 2.052,0.948 2.5,0.25 false 2.781,0.177 3.094,0.375 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 2 indoor electrical key antenna assembly (rear floor) is operating by the sounding of the buzzer.

·

When the wireless buzzer does not sound for No. 2 indoor electrical key antenna assemby (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 2 indoor electrical key antenna assembly (rear floor), is malfunctioning.




Result:
Result Proceed to
The wireless buzzer sounds A
The wireless buzzer does not sound B



A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

B

AFFECTED BY WAVE INTERFERENCE

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Disconnect the G214 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R14*1 or s1*2 No. 2 indoor electrical key antenna assembly (rear floor) connector.

*1: for 3 Door

*2: for 5 Door



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G214-15 (CLG6) - R14-1 (CLG)*1 Always Below 1 Ω
G214-15 (CLG6) - s1-1 (CLG)*2 Always Below 1 Ω
G214-14 (CG6B) - R14-2 (CLGB)*1 Always Below 1 Ω
G214-14 (CG6B) - s1-2 (CLGB)*2 Always Below 1 Ω
G214-15 (CLG6) or R14-1 (CLG) - Body ground*1 Always 10 kΩ or higher
G214-15 (CLG6) or s1-1 (CLG) - Body ground*2 Always 10 kΩ or higher
G214-14 (CG6B) or R14-2 (CLGB) - Body ground*1 Always 10 kΩ or higher
G214-14 (CG6B) or s1-2 (CLGB) - Body ground*2 Always 10 kΩ or higher


*1: for 3 Door

*2: for 5 Door



d.

Reconnect the G214 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR))
a.

Using an oscilloscope, check the waveform.

B492527C01
1.417,0.625 1.75,0.833 0.333,0.208 1.917,0.625 2.25,0.833 0.333,0.208 1.479,2.125 1.76,1.583 true 2.271,2.135 1.979,1.573 true 1.469,0.427 1.781,0.583 0.313,0.156 10 false *A 2,0.427 2.313,0.583 0.313,0.156 10 false *B 0.583,0.25 0.896,0.406 0.313,0.156 10 false *a 3.854,0.25 4.167,0.406 0.313,0.156 10 false *b 4.771,2 5.083,2.156 0.313,0.156 10 false *c 5.583,2.01 5.896,2.167 0.313,0.156 10 false *d 3.948,1.302 4.406,1.5 0.458,0.198 10 false GND 2.083,2.135 2.604,2.333 0.521,0.198 10 false CLGB 1.313,2.135 1.833,2.333 0.521,0.198 10 false CLG 1.51,0.635 1.823,0.833 0.313,0.198 10 false s1 1.958,0.635 2.271,0.833 0.313,0.198 10 false R14
*A for 5 Door *B for 3 Door
*a Front view of wire harness connector
(to No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
s1-1 (CLG) - s1-2 (CLGB)*1 Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)
R14-1 (CLG) - R14-2 (CLGB)*2 Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


*1: for 5 Door

*2: for 3 Door



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK WAVE ENVIRONMENT
a.

Install the transmitter battery to the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>REMOVAL


b.

Bring the electrical key transmitter sub-assembly near the No. 3 indoor electrical key antenna assembly (inside luggage) and perform an entry and start system check.

HINT:

Check that the customize setting "Ignition Available Area" is set to "All".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>CUSTOMIZE PARAMETERS


NOTICE:

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION



HINT:
·

As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.



OK:

The engine starts when the electrical key transmitter sub-assembly is held near each indoor electrical key antenna assembly and the engine switch is pressed with the brake pedal (for Automatic Transmission) or clutch pedal (for Manual Transmission) depressed.


Result:
Proceed to
OK
NG



OK

AFFECTED BY WAVE INTERFERENCE

NG

11.CHECK KEY DIAGNOSTIC MODE
11.CHECK KEY DIAGNOSTIC MODE
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check(Key Diag Mode).


e.
B485495C01
1.354,1.802 2.5,0.333 2.5,0.333 2.75,0.333 false 1.99,1.25 2.5,0.333 false 2.802,0.25 3.115,0.448 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 3 indoor electrical key antenna assembly (inside luggage).

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless buzzer sounds.

HINT:
·

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

·

It is possible to check which No. 3 indoor electrical key antenna assembly (inside luggage) is operating by the sounding of the buzzer.

·

When the wireless buzzer does not sound for No. 1 indoor electrical key antenna assemby (rear floor), it can be judged that the certification ECU (smart key ECU assembly), which controls the No. 3 indoor electrical key antenna assembly (inside luggage), is malfunctioning.




Result:
Result Proceed to
The wireless buzzer sounds A
The wireless buzzer does not sound B



A

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE))

B

AFFECTED BY WAVE INTERFERENCE

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE))
a.

Disconnect the G214 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the R15 No. 3 indoor electrical key antenna assembly (inside luggage) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G214-4 (CLG7) - R15-1 (CLG) Always Below 1 Ω
G214-3 (CG7B) - R15-2 (CLGB) Always Below 1 Ω
G214-4 (CLG7) or R15-1 (CLG) - Body ground*1 Always 10 kΩ or higher
G214-3 (CG7B) or R15-2 (CLGB) - Body ground*1 Always 10 kΩ or higher



d.

Reconnect the G214 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE))
a.

Using an oscilloscope, check the waveform.

B492527C02
1.719,0.625 2.052,0.833 0.333,0.208 1.427,2.146 1.74,1.583 true 2.229,2.146 1.927,1.583 true 0.583,0.25 0.896,0.406 0.313,0.156 10 false *a 3.854,0.25 4.167,0.406 0.313,0.156 10 false *b 4.771,2 5.083,2.156 0.313,0.156 10 false *c 5.583,2.01 5.896,2.167 0.313,0.156 10 false *d 3.948,1.302 4.406,1.5 0.458,0.198 10 false GND 2.083,2.146 2.604,2.344 0.521,0.198 10 false CLGB 1.302,2.146 1.823,2.344 0.521,0.198 10 false CLG 1.76,0.635 2.073,0.833 0.313,0.198 10 false R15
*a Front view of wire harness connector
(to No. 3 Indoor Electrical Key Antenna Assembly (Inside Luggage))
*b Waveform
*c For 30 seconds after closing any door *d After 30 seconds or more have elapsed since any door closed


OK:
Tester Connection Condition Tool Setting Specified Condition
R15-1 (CLG) - R15-2 (CLGB) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Proceed to
OK
NG



OK

REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the electrical key transmitter sub-assembly for 5 seconds and check the number of times that the LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. "Yes" is displayed for the Data List item "Key Low Battery" when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.





Result:
Result Proceed to
LED illuminates 3 times or more when switch is pressed and held A
LED does not illuminate when switch is pressed and held B
LED illuminates once or twice but not a third time C



A

15.CHECK ENTRY LOCK / UNLOCK FUNCTION

B

21.INSPECT TRANSMITTER BATTERY

C

15.CHECK ENTRY LOCK / UNLOCK FUNCTION
a.

Check that the entry lock and unlock functions operate on each door.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK

HINT:

If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.



Result:
Result Proceed to
Entry lock/unlock functions operate normally A
An entry lock/unlock functions does not operate normally B



A

16.READ VALUE USING GTS (START SWITCH1, START SWITCH2)

B

GO TO ENTRY AND START SYSTEM (for Entry Function) (All door entry lock/unlock functions and wireless functions do not operate)

16.READ VALUE USING GTS (START SWITCH1, START SWITCH2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

Read the Data List according to the display on the GTS.

Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status OFF or ON OFF: Engine switch not pressed
ON: Engine switch pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine if the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status OFF or ON OFF: Engine switch not pressed
ON: Engine switch pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the power source mode can only be changed when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.



OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

19.INSPECT ENGINE SWITCH
17.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Enter the following menus: Body Electrical / Power Source Control / Data List.


b.

Measure the voltage while confirming the power source mode on the Data List.

B343119C88
1.667,0.271 2.094,0.5 0.427,0.229 5.104,0.25 5.531,0.479 0.427,0.229 4.344,1.948 4.552,1.948 4.552,1.948 4.677,0.958 true 0.906,1.906 1.073,1.906 1.073,1.906 1.406,0.917 true 3.938,1.875 4.396,2.073 0.458,0.198 10 false ACCD 1.719,0.302 2.177,0.5 0.458,0.198 10 false G213 0.573,1.823 1.031,2.021 0.458,0.198 10 false IG1D 0.167,0.104 0.625,0.302 0.458,0.198 10 false *a 5.146,0.281 5.604,0.479 0.458,0.198 10 false G215
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Power Source Control
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G213-3 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC)
Engine switch on (IG) 9 V or higher
G215-9 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG)



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

18.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.
C376684C05
1.51,0.26 1.938,0.458 0.427,0.198 1.656,0.292 1.969,0.49 0.313,0.198 10 false 2N 0.146,0.229 0.458,0.427 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Driver Side Junction Block Assembly)


Disconnect the driver side junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT ENGINE SWITCH


Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

NG

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the G215 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G215-16 (SSW1) - G206-5 (SS1) Always Below 1 Ω
G215-18 (SSW2) - G206-1 (SS2) Always Below 1 Ω
G215-12 (AGND) - G206-6 (AGND) Always Below 1 Ω
G215-16 (SSW1) or G206-5 (SS1) - Body ground Always 10 kΩ or higher
G215-18 (SSW2) or G206-1 (SS2) - Body ground Always 10 kΩ or higher
G215-12 (AGND) or G206-6 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT TRANSMITTER BATTERY
a.

Inspect the transmitter battery.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Entry and Start System)>INSPECTION

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG