Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2017.08
RM27T0E _58 Vehicle Interior _053738 SEAT BELT _0261145 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter detects the state of the front seat inner belt RH*1 (or LH*2) when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the front seat belt warning light in the combination meter blinks. If the seat belt is fastened, the warning light goes off.

*1: for LHD

*2: for RHD


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

E378410E01
4.927,3.177 7.115,3.5 2.188,0.323 10 false Combination Meter Assembly 5.469,0.917 6.167,1.135 0.698,0.219 10 false P/SB*3 5.458,1.167 6.156,1.385 0.698,0.219 10 false PBKL*4 5.083,1.01 5.427,1.219 0.344,0.208 10 false G7 4.531,1 4.969,1.271 0.438,0.271 10 false G304 5.052,0.76 5.458,0.969 0.406,0.208 10 false 15*3 4.552,0.76 4.958,0.969 0.406,0.208 10 false 11*4 3.833,1.604 4.24,1.813 0.406,0.208 10 false 2 3.615,0.875 4.021,1.083 0.406,0.208 10 false + 3.604,1.615 4.01,1.823 0.406,0.208 10 false E 2.802,1.177 3.917,1.469 1.115,0.292 10 false Buckle Switch 1.052,1.104 1.823,1.76 0.771,0.656 10 false Occupant Detection Sensor 2.552,2.385 4.073,2.833 1.521,0.448 10 false Front Seat Inner Belt Assembly RH*1, LH*2 2.563,2.219 3.74,2.406 1.177,0.188 10 false Q21*1, R34*2 0.323,3.031 1.5,3.219 1.177,0.188 10 false *1: for LHD 0.323,3.385 1.5,3.573 1.177,0.188 10 false *2: for RHD 1.427,3.021 2.604,3.208 1.177,0.188 10 false *3: for 5L-E 1.427,3.385 2.604,3.573 1.177,0.188 10 false *4: except 5L-E 2.542,0.885 2.948,1.094 0.406,0.208 10 false 1 3.823,0.875 4.229,1.083 0.406,0.208 10 false 3 2.542,1.625 2.948,1.833 0.406,0.208 10 false 3 0.802,2.219 2.51,2.719 1.708,0.5 10 false Separate Type Front Seat Cushion Pad

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P- Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat belt fastened
OFF: Front passenger side seat belt unfastened
Perform the inspection while sitting in the front passenger side seat.

OK:

The display is as specified in the normal condition column.




OK

2.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

NG

REPLACE COMBINATION METER ASSEMBLY

2.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.

Remove the front seat assembly (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).


C213678

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 More than 147 N (15 kgf, 33.0 lbf) applied to occupant detection sensor Below 100 Ω




OK

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY
a.
C213676E03
1.528,1.637 1.739,1.835 0.211,0.198 10 + 1.965,1.654 2.176,1.852 0.211,0.198 10 E 1.701,1.143 1.604,1.601 false 1.887,1.118 1.995,1.637 false

Remove the front seat inner belt assembly RH*1 or LH*2 (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (E) - 3 Always Below 1 Ω
3 (+) - 1 Front passenger side seat belt unfastened
3 (+) - 1 Front passenger side seat belt fastened 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT PASSENGER SIDE INNER BELT AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT PASSENGER SIDE INNER BELT AND BODY GROUND)
a.

Disconnect the G7*1 or G304*2 meter connector.

*1: for 5L-E

*2: except 5L-E



b.

Disconnect the Q21*3 or R34*4 inner belt connector.

*3: for LHD

*4: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5L-E):
for LHD
Tester Connection Condition Specified Condition
G7-15 (P/SB) - Q21-3 (+) Always Below 1 Ω
Q21-2 (E) - Body ground
G7-15 (P/SB) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G7-15 (P/SB) - R34-3 (+) Always Below 1 Ω
R34-2 (E) - Body ground
G7-15 (P/SB) - Body ground Always 10 kΩ or higher


Standard Resistance (except 5L-E):
for LHD
Tester Connection Condition Specified Condition
G304-11 (PBKL) - Q21-3 (+) Always Below 1 Ω
Q21-2 (E) - Body ground
G304-11 (PBKL) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G304-11 (PBKL) - R34-3 (+) Always Below 1 Ω
R34-2 (E) - Body ground
G304-11 (PBKL) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR