This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna assembly which is connected to the radio and display receiver assembly.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B157D | The digital audio broadcasting antenna assembly is not connected | ·
Digital audio broadcasting antenna assembly ·
No. 2 antenna cord sub-assembly ·
Radio and display receiver assembly ·
Harness or connector |
Check for DTCs (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
Optional components are installed.
Do not remove optional components without permission of the customer.
OK
NG
Inspect the windshield glass antenna wire (See page Audio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR).
OK
NG
Remove the antenna connector from the radio and display receiver assembly.
Turn the engine switch on (ACC) with the radio and display receiver assembly connector connected.
Turn on the radio and turn into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly antenna jack and check that noise can be heard from the speakers.
Noise occurs.
| Result | Proceed to |
|---|---|
| OK (w/o Heated Windshield Defroster System) | A |
| OK (w/ Telematics Transceiver and w/ Heated Windshield Defroster System) | B |
| NG | C |
A
B
C
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the DB radio and display receiver assembly connector.
Disconnect the antenna connector from the No.2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DB-1 - 1 | Always | Below 1 Ω |
| DB-1-a - 1-a | Always | Below 1 Ω |
| DB-1 - Body ground | Always | 10 kΩ or higher |
| DB-1-a - Body ground | Always | 10 kΩ or higher |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the DB radio and display receiver assembly connector.
Disconnect the antenna connector from the No.2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DB-1 - 1 | Always | Below 1 Ω |
| DB-1-a - 1-a | Always | Below 1 Ω |
| DB-1 - Body ground | Always | 10 kΩ or higher |
| DB-1-a - Body ground | Always | 10 kΩ or higher |
OK
NG
| *a | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly) |
| *b | Front view of wire harness connector
(to Vehicle Wire Harness) |
Disconnect the antenna connector from the radio and display receiver assembly.
Disconnect the antenna connector from the digital audio broadcasting antenna assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-a - 1-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly) |
| *b | Front view of wire harness connector
(to Vehicle Wire Harness) |
OK
NG
| *a | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly) |
| *b | Front view of wire harness connector
(to Vehicle Wire Harness) |
Disconnect the antenna connector from the radio and display receiver assembly.
Disconnect the antenna connector from the digital audio broadcasting antenna assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-a - 1-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| 1-a - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly) |
| *b | Front view of wire harness connector
(to Vehicle Wire Harness) |
OK
NG
Replace the digital audio broadcasting antenna assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL).
Check for DTCs (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).
No DTCs are output.
OK
NG
(See pageAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL)