When a malfunction in the fuel pump circuit is detected, DTC P0230 is stored.
The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed among 3 settings. The fuel pump ECU also has a self-diagnosis function. Based on the fuel pump circuit condition, the fuel pump ECU outputs a diagnostic signal (DI) to the ECM, and the ECM determines if there is a malfunction in the fuel pump circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0230 | Either condition is met (1 trip detection logic):
·
When the fuel pump is operating: -
The remaining fuel is 17 L or more. -
The DI terminal output is low. ·
When the fuel pump is not operating: -
The DI terminal output is high. |
·
Open or short in fuel pump circuit ·
Fuel pump ·
Fuel pump ECU ·
ECM |
To monitor the fuel pump circuit, the ECM checks the fuel pump control signal (FPC) and diagnostic signal (DI). The FPC voltage varies between approximately 0 V and approximately 12 V (duty signal). Based on the condition of the fuel pump ECU malfunction, the DI voltage varies between approximately 0 V and approximately 12 V. The ECM then compares the variance of the FPC voltage and DI voltage, and determines if the fuel pump circuit is malfunctioning. When the ECM determines that the fuel pump circuit is malfunctioning, a DTC is stored immediately.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the Problem Symptoms Table (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Enter the following menus: Body Electrical / Combination Meter / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC B1500 is not output | A |
| DTC B1500 is output | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the fuel pump / Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.
Operating sounds can be heard from fuel pump.
OK
NG
Inspect the NO. 1 integration relay (C/OPN relay) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-7 - G55-5(FC) | Always | Below 1 Ω |
| 1V-6 - S8-4 (+B) | Always | Below 1 Ω |
| 1V-1 - 1W-12 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-7 - G56-8(FC) | Always | Below 1 Ω |
| 1V-6 - S8-4 (+B) | Always | Below 1 Ω |
| 1V-1 - 1W-12 | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-7 or G55-5 (FC) - Body ground | Always | 10 kΩ or higher |
| 1V-6 or S8-4 (+B) - Body ground | Always | 10 kΩ or higher |
| 1V-1 or 1W-12 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1V-7 or G56-8 (FC) - Body ground | Always | 10 kΩ or higher |
| 1V-6 or S8-4 (+B) - Body ground | Always | 10 kΩ or higher |
| 1V-1 or 1W-12 - Body ground | Always | 10 kΩ or higher |
Reinstall the No. 1 integration relay.
Reconnect the fuel pump ECU connector.
Reconnect the ECM connector.
OK
NG
Disconnect the fuel sender gauge connector.
Disconnect the fuel pump ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S5-4 (B2) - S9-1 (FP) | Always | Below 1 Ω |
| S5-5 (E2) - S9-2 (FP-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S5-4 (B2) or S9-1 (FP) - Body ground | Always | 10 kΩ or higher |
| S5-5 (E2) or S9-2 (FP-) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel sender gauge connector.
Reconnect the fuel pump ECU connector.
OK
NG
Inspect the fuel pump.
for Single Tank Type (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Single Tank Type)>INSPECTION)
for Double Tank Type (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP (for Double Tank Type)>INSPECTION).
| Test Result | Proceed to |
|---|---|
| OK | A |
| NG (for Single Tank Type) | B |
| NG (for Double Tank Type) | C |
Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION).
A
B
C
Disconnect the fuel pump ECU connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-1 (FPC) - G55-4 (FPC) | Always | Below 1 Ω |
| S8-2 (DI) - G55-14 (DI) | Always | Below 1 Ω |
| S8-3 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-1 (FPC) - G55-3 (FPC) | Always | Below 1 Ω |
| S8-2 (DI) - G56-26 (DI) | Always | Below 1 Ω |
| S8-3 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-1 (FPC) or G55-4 (FPC) - Body ground | Always | 10 kΩ or higher |
| S8-2 (DI) or G55-14 (DI) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S8-1 (FPC) or G55-3 (FPC) - Body ground | Always | 10 kΩ or higher |
| S8-2 (DI) or G56-26 (DI) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel pump ECU connector.
Reconnect the ECM connector.
OK
NG
Replace the fuel pump ECU (See page Engine / Hybrid System>1GR-FE (FUEL)>FUEL PUMP ECU>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine and idle it for 5 minutes.
Drive the vehicle in an urban area for approximately 10 minutes.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No output | A |
| DTC P0230 is output | B |
A
B