Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  C1AEC  Front Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the front sensors and ECU, or when there is a malfunction in a front sensor.

DTC Code DTC Detection Condition Trouble Area
C1AEC An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the ignition switch is turned ON.
·

Front ultrasonic sensor circuit

·

Clearance warning ECU



WIRING DIAGRAM

E283768E25
5.615,2.115 6.229,2.313 0.615,0.198 10 false G228 5.615,2.281 6.844,2.656 1.229,0.375 10 false Clearance Warning ECU 5.75,1.031 6.365,1.229 0.615,0.198 10 false SOF 5.75,1.302 6.365,1.5 0.615,0.198 10 false BOF 3.969,1.604 4.177,1.813 0.208,0.208 10 false EI 5.531,0.938 5.75,1.125 0.219,0.188 10 false 8 5.521,1.229 5.74,1.417 0.219,0.188 10 false 4 5.51,1.51 5.729,1.698 0.219,0.188 10 false 6 3.042,1.969 3.656,2.167 0.615,0.198 10 false B11 3.042,2.135 4.625,2.573 1.583,0.438 10 false NO. 1 Ultrasonic Sensor (Front Corner Sensor LH) 0.698,1.948 1.313,2.146 0.615,0.198 10 false B12 0.708,2.135 2.26,2.625 1.552,0.49 10 false NO. 1 Ultrasonic Sensor (Front Center Sensor LH) 0.719,3.969 1.333,4.167 0.615,0.198 10 false B13 0.719,4.156 2.302,4.729 1.583,0.573 10 false NO. 1 Ultrasonic Sensor (Front Center Sensor RH) 3.021,3.979 3.635,4.177 0.615,0.198 10 false B14 3.021,4.156 4.594,4.719 1.573,0.563 10 false NO. 1 Ultrasonic Sensor (Front Corner Sensor RH) 5.75,1.573 6,1.792 0.25,0.219 10 false E5 3.969,1.323 4.177,1.531 0.208,0.208 10 false BI 3.969,1.042 4.177,1.25 0.208,0.208 10 false SI 3.177,1.052 3.479,1.281 0.302,0.229 10 false SO 3.177,1.323 3.448,1.521 0.271,0.198 10 false BO 3.177,1.594 3.458,1.813 0.281,0.219 10 false EO 0.958,1.021 1.25,1.229 0.292,0.208 10 false SO 0.969,1.302 1.229,1.531 0.26,0.229 10 false BO 0.969,1.583 1.271,1.802 0.302,0.219 10 false EO 1.76,1.01 1.969,1.219 0.208,0.208 10 false SI 1.771,1.292 1.979,1.5 0.208,0.208 10 false BI 1.771,1.583 1.979,1.792 0.208,0.208 10 false EI 0.969,3.031 1.177,3.24 0.208,0.208 10 false SI 0.969,3.323 1.177,3.531 0.208,0.208 10 false BI 0.969,3.615 1.177,3.823 0.208,0.208 10 false EI 1.708,3.052 1.979,3.24 0.271,0.188 10 false SO 1.708,3.323 1.969,3.552 0.26,0.229 10 false BO 1.708,3.604 2.01,3.823 0.302,0.219 10 false EO 3.208,3.042 3.417,3.25 0.208,0.208 10 false SI 3.219,3.313 3.427,3.521 0.208,0.208 10 false BI 3.219,3.604 3.427,3.813 0.208,0.208 10 false EI 4.26,0.948 4.479,1.135 0.219,0.188 10 false 3 4.26,1.229 4.479,1.417 0.219,0.188 10 false 1 4.271,1.5 4.49,1.688 0.219,0.188 10 false 5 2.031,0.938 2.25,1.125 0.219,0.188 10 false 3 2.031,1.24 2.25,1.427 0.219,0.188 10 false 1 2.042,1.5 2.26,1.688 0.219,0.188 10 false 5 0.771,2.958 0.99,3.146 0.219,0.188 10 false 3 0.76,3.25 0.979,3.438 0.219,0.188 10 false 1 0.771,3.542 0.99,3.729 0.219,0.188 10 false 5 3,2.969 3.219,3.156 0.219,0.188 10 false 3 3,3.26 3.219,3.448 0.219,0.188 10 false 1 3.01,3.531 3.229,3.719 0.219,0.188 10 false 5 2.958,0.948 3.177,1.135 0.219,0.188 10 false 4 2.958,1.219 3.177,1.406 0.219,0.188 10 false 2 2.958,1.51 3.177,1.698 0.219,0.188 10 false 6 0.781,0.938 1,1.125 0.219,0.188 10 false 4 0.771,1.219 0.99,1.406 0.219,0.188 10 false 2 0.771,1.49 0.99,1.677 0.219,0.188 10 false 6 2.042,2.938 2.26,3.125 0.219,0.188 10 false 4 2.042,3.25 2.26,3.438 0.219,0.188 10 false 2 2.042,3.531 2.26,3.719 0.219,0.188 10 false 6

PROCEDURE

1.CHECK FOR DTC

A

B

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - FRONT CORNER SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - FRONT CORNER SENSOR LH)
a.

Disconnect the G228 clearance warning ECU connector.


b.

Disconnect the B11 No. 1 ultrasonic sensor (front corner sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G228-4 (BOF) - B11-1 (BI) Always Below 1 Ω
G228-8 (SOF) - B11-3 (SI) Always Below 1 Ω
G228-6 (E5) - B11-5 (EI) Always Below 1 Ω
G228-4 (BOF) - Body ground Always 10 kΩ or higher
G228-8 (SOF) - Body ground Always 10 kΩ or higher
G228-6 (E5) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (FRONT CORNER SENSOR LH - FRONT CENTER SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FRONT CORNER SENSOR LH - FRONT CENTER SENSOR LH)
a.

Disconnect the B11 No. 1 ultrasonic sensor (front corner sensor LH) connector.


b.

Disconnect the B12 No. 1 ultrasonic sensor (front center sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B11-2 (BO) - B12-1 (BI) Always Below 1 Ω
B11-4 (SO) - B12-3 (SI) Always Below 1 Ω
B11-6 (EO) - B12-5 (EI) Always Below 1 Ω
B11-2 (BO) - Body ground Always 10 kΩ or higher
B11-4 (SO) - Body ground Always 10 kΩ or higher
B11-6 (EO) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FRONT CENTER SENSOR LH - FRONT CENTER SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT CENTER SENSOR LH - FRONT CENTER SENSOR RH)
a.

Disconnect the B12 No. 1 ultrasonic sensor (front center sensor LH) connector.


b.

Disconnect the B13 No. 1 ultrasonic sensor (front center sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B12-2 (BO) - B13-1 (BI) Always Below 1 Ω
B12-4 (SO) - B13-3 (SI) Always Below 1 Ω
B12-6 (EO) - B13-5 (EI) Always Below 1 Ω
B12-2 (BO) - Body ground Always 10 kΩ or higher
B12-4 (SO) - Body ground Always 10 kΩ or higher
B12-6 (EO) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (FRONT CENTER SENSOR RH - FRONT CORNER SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (FRONT CENTER SENSOR RH - FRONT CORNER SENSOR RH)
a.

Disconnect the B13 No. 1 ultrasonic sensor (front center sensor RH) connector.


b.

Disconnect the B14 No. 1 ultrasonic sensor (front corner sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B13-2 (BO) - B14-1 (BI) Always Below 1 Ω
B13-4 (SO) - B14-3 (SI) Always Below 1 Ω
B13-6 (EO) - B14-5 (EI) Always Below 1 Ω
B13-2 (BO) - Body ground Always 10 kΩ or higher
B13-4 (SO) - Body ground Always 10 kΩ or higher
B13-6 (EO) - Body ground Always 10 kΩ or higher




OK

6.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (front corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (front corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>INSPECTION).



OK

7.INSPECT ULTRASONIC SENSOR FRONT CENTER (FRONT CENTER SENSOR LH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)

7.INSPECT ULTRASONIC SENSOR FRONT CENTER (FRONT CENTER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (front center sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (front center sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>INSPECTION).



OK

8.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR RH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR LH)

8.INSPECT NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR RH)
a.

Remove the No. 1 ultrasonic sensor (front center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (front center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>INSPECTION).



OK

9.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR RH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR RH)

9.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor (front corner sensor RH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).



NEXT

10.CHECK FOR DTC (C1AEC)
10.CHECK FOR DTC (C1AEC)

A

END (NO. 1 ULTRASONIC SENSOR [FRONT CORNER SENSOR RH] WAS DEFECTIVE)

B

11.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR LH)
11.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR LH)
a.

Replace the No. 1 ultrasonic sensor (front center sensor LH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

12.CHECK FOR DTC (C1AEC)
12.CHECK FOR DTC (C1AEC)

A

END (NO. 1 ULTRASONIC SENSOR [FRONT CENTER SENSOR LH] WAS DEFECTIVE)

B

13.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR RH)
13.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CENTER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor (front center sensor RH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

14.CHECK FOR DTC (C1AEC)
14.CHECK FOR DTC (C1AEC)

A

END (NO. 1 ULTRASONIC SENSOR [FRONT CENTER SENSOR RH] WAS DEFECTIVE)

B

15.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)
15.REPLACE NO. 1 ULTRASONIC SENSOR (FRONT CORNER SENSOR LH)
a.

Replace the No. 1 ultrasonic sensor (front corner sensor LH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Front)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

16.CHECK FOR DTC (C1AEC)
16.CHECK FOR DTC (C1AEC)

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display)>DTC CHECK / CLEAR).

Result
Result Proceed to
No DTC is output A
DTC C1AEC is output (for LHD) B
DTC C1AEC is output (for RHD) C



A

END (NO. 1 ULTRASONIC SENSOR [FRONT CORNER SENSOR RH] WAS DEFECTIVE)

B

C