Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display) › from 2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261009 TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display) C

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(w/ Multi-display)  C1AED  Rear Sensor Communication Malfunction  


DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and ECU, or when there is a malfunction in a rear sensor.

DTC Code DTC Detection Condition Trouble Area
C1AED An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the ignition switch is turned ON.
·

Rear ultrasonic sensor circuit

·

Clearance warning ECU



WIRING DIAGRAM

E283768E26
5.417,2.104 6.354,2.292 0.938,0.188 10 false I9*1, G228*2 5.396,2.281 7.094,2.708 1.698,0.427 10 false Clearance Warning ECU 5.75,1.031 6.365,1.229 0.615,0.198 10 false SOR 5.75,1.302 6.365,1.5 0.615,0.198 10 false BOR 3.969,1.604 4.177,1.813 0.208,0.208 10 false EI 5.479,0.927 5.698,1.115 0.219,0.188 10 false 24 5.469,1.229 5.688,1.417 0.219,0.188 10 false 22 5.469,1.5 5.688,1.688 0.219,0.188 10 false 23 3.042,1.948 3.656,2.146 0.615,0.198 10 false V7 3.042,2.135 4.625,2.573 1.583,0.438 10 false NO. 1 Ultrasonic Sensor (Rear Corner Sensor LH) 0.698,1.948 1.313,2.146 0.615,0.198 10 false V6 0.708,2.135 2.292,2.625 1.583,0.49 10 false NO. 1 Ultrasonic Sensor (Rear Center Sensor LH) 0.719,3.969 1.333,4.167 0.615,0.198 10 false U6 0.719,4.156 2.302,4.729 1.583,0.573 10 false NO. 1 Ultrasonic Sensor (Rear Center Sensor RH) 3.021,3.979 3.635,4.177 0.615,0.198 10 false U7 3.021,4.156 4.594,4.719 1.573,0.563 10 false NO. 1 Ultrasonic Sensor (Rear Corner Sensor RH) 5.75,1.573 6,1.792 0.25,0.219 10 false E1 3.969,1.323 4.177,1.531 0.208,0.208 10 false BI 3.969,1.042 4.177,1.25 0.208,0.208 10 false SI 3.177,1.052 3.479,1.281 0.302,0.229 10 false SO 3.177,1.323 3.448,1.521 0.271,0.198 10 false BO 3.177,1.594 3.458,1.813 0.281,0.219 10 false EO 0.958,1.021 1.25,1.229 0.292,0.208 10 false SO 0.969,1.302 1.229,1.531 0.26,0.229 10 false BO 0.969,1.583 1.271,1.802 0.302,0.219 10 false EO 1.781,1.01 1.99,1.219 0.208,0.208 10 false SI 1.771,1.292 1.979,1.5 0.208,0.208 10 false BI 1.771,1.583 1.979,1.792 0.208,0.208 10 false EI 0.969,3.031 1.177,3.24 0.208,0.208 10 false SI 0.969,3.323 1.177,3.531 0.208,0.208 10 false BI 0.969,3.615 1.177,3.823 0.208,0.208 10 false EI 1.708,3.052 1.979,3.24 0.271,0.188 10 false SO 1.708,3.323 1.969,3.552 0.26,0.229 10 false BO 1.708,3.604 2.01,3.823 0.302,0.219 10 false EO 3.208,3.042 3.417,3.25 0.208,0.208 10 false SI 3.219,3.313 3.427,3.521 0.208,0.208 10 false BI 3.219,3.604 3.427,3.813 0.208,0.208 10 false EI 4.26,0.948 4.479,1.135 0.219,0.188 10 false 3 4.26,1.229 4.479,1.417 0.219,0.188 10 false 1 4.271,1.5 4.49,1.688 0.219,0.188 10 false 5 2.031,0.938 2.25,1.125 0.219,0.188 10 false 3 2.031,1.24 2.25,1.427 0.219,0.188 10 false 1 2.042,1.5 2.26,1.688 0.219,0.188 10 false 5 0.771,2.958 0.99,3.146 0.219,0.188 10 false 3 0.76,3.25 0.979,3.438 0.219,0.188 10 false 1 0.771,3.542 0.99,3.729 0.219,0.188 10 false 5 3,2.969 3.219,3.156 0.219,0.188 10 false 3 3,3.26 3.219,3.448 0.219,0.188 10 false 1 3.01,3.531 3.229,3.719 0.219,0.188 10 false 5 2.958,0.948 3.177,1.135 0.219,0.188 10 false 4 2.958,1.219 3.177,1.406 0.219,0.188 10 false 2 2.958,1.51 3.177,1.698 0.219,0.188 10 false 6 0.781,0.938 1,1.125 0.219,0.188 10 false 4 0.771,1.219 0.99,1.406 0.219,0.188 10 false 2 0.771,1.49 0.99,1.677 0.219,0.188 10 false 6 2.042,2.938 2.26,3.125 0.219,0.188 10 false 4 2.042,3.25 2.26,3.438 0.219,0.188 10 false 2 2.042,3.531 2.26,3.719 0.219,0.188 10 false 6 0.135,5.021 1.646,5.229 1.51,0.208 10 false *1: for 4 Sensor Type 0.135,5.354 1.646,5.563 1.51,0.208 10 false *2: for 8 Sensor Type

PROCEDURE

1.CHECK FOR DTC (C1AED)

A

B

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - REAR CORNER SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - REAR CORNER SENSOR LH)
a.

Disconnect the I9*1 or G228*2 clearance warning ECU connector.

*1: for 4 Sensor Type

*2: for 8 Sensor Type



b.

Disconnect the V7 No. 1 ultrasonic sensor (rear corner sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 4 Sensor Type
Tester Connection Condition Specified Condition
I9-22 (BOR) - V7-1 (BI) Always Below 1 Ω
I9-24 (SOR) - V7-3 (SI) Always Below 1 Ω
I9-23 (E1) - V7-5 (EI) Always Below 1 Ω
I9-22 (BOR) - Body ground Always 10 kΩ or higher
I9-24 (SOR) - Body ground Always 10 kΩ or higher
I9-23 (E1) - Body ground Always 10 kΩ or higher

for 8 Sensor Type
Tester Connection Condition Specified Condition
G228-22 (BOR) - V7-1 (BI) Always Below 1 Ω
G228-24 (SOR) - V7-3 (SI) Always Below 1 Ω
G228-23 (E1) - V7-5 (EI) Always Below 1 Ω
G228-22 (BOR) - Body ground Always 10 kΩ or higher
G228-24 (SOR) - Body ground Always 10 kΩ or higher
G228-23 (E1) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR LH - REAR CENTER SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR LH - REAR CENTER SENSOR LH)
a.

Disconnect the V7 No. 1 ultrasonic sensor (rear corner sensor LH) connector.


b.

Disconnect the V6 No. 1 ultrasonic sensor (rear center sensor LH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V7-2 (BO) - V6-1 (BI) Always Below 1 Ω
V7-4 (SO) - V6-3 (SI) Always Below 1 Ω
V7-6 (EO) - V6-5 (EI) Always Below 1 Ω
V7-2 (BO) - Body ground Always 10 kΩ or higher
V7-4 (SO) - Body ground Always 10 kΩ or higher
V7-6 (EO) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR LH - REAR CENTER SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR LH - REAR CENTER SENSOR RH)
a.

Disconnect the V6 No. 1 ultrasonic sensor (rear center sensor LH) connector.


b.

Disconnect the U6 No. 1 ultrasonic sensor (rear center sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V6-2 (BO) - U6-1 (BI) Always Below 1 Ω
V6-4 (SO) - U6-3 (SI) Always Below 1 Ω
V6-6 (EO) - U6-5 (EI) Always Below 1 Ω
V6-2 (BO) - Body ground Always 10 kΩ or higher
V6-4 (SO) - Body ground Always 10 kΩ or higher
V6-6 (EO) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH)
a.

Disconnect the U6 No. 1 ultrasonic sensor (rear center sensor RH) connector.


b.

Disconnect the U7 No. 1 ultrasonic sensor (rear corner sensor RH) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U6-2 (BO) - U7-1 (BI) Always Below 1 Ω
U6-4 (SO) - U7-3 (SI) Always Below 1 Ω
U6-6 (EO) - U7-5 (EI) Always Below 1 Ω
U6-2 (BO) - Body ground Always 10 kΩ or higher
U6-4 (SO) - Body ground Always 10 kΩ or higher
U6-6 (EO) - Body ground Always 10 kΩ or higher




OK

6.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (rear corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear corner sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

7.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)

7.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)
a.

Remove the No. 1 ultrasonic sensor (rear center sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear center sensor LH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

8.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)

8.INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.

Remove the No. 1 ultrasonic sensor (rear center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).


b.

Inspect the No. 1 ultrasonic sensor (rear center sensor RH) (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>INSPECTION).



OK

9.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)

NG

REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)

9.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor (rear corner sensor RH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

10.CHECK FOR DTC (C1AED)
10.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CORNER SENSOR RH] WAS DEFECTIVE)

B

11.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)
11.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH)
a.

Replace the No. 1 ultrasonic sensor (rear center sensor LH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

12.CHECK FOR DTC (C1AED)
12.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CENTER SENSOR LH] WAS DEFECTIVE)

B

13.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
13.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH)
a.

Replace the No. 1 ultrasonic sensor (rear center sensor RH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

14.CHECK FOR DTC (C1AED)
14.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CENTER SENSOR RH] WAS DEFECTIVE)

B

15.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
15.REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH)
a.

Replace the No. 1 ultrasonic sensor (rear corner sensor LH) with a normally functioning sensor (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>ULTRASONIC SENSOR(for Rear)>REMOVAL).

HINT:

All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.




NEXT

16.CHECK FOR DTC (C1AED)
16.CHECK FOR DTC (C1AED)

A

END (NO. 1 ULTRASONIC SENSOR [REAR CORNER SENSOR LH] WAS DEFECTIVE)

B

C