The combination meter assembly receives a text data signal from the navigation receiver assembly (for Navigation Receiver Type) or radio and display receiver assembly (for Radio and Display Type) via local bus communication.
Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.
This DTC is stored when the combination meter assembly cannot receive the signal.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B150A | Both conditions are met:
After the combination meter assembly receives a registration information signal, which is sent by the navigation receiver assembly (for Navigation Receiver Type) or radio and display receiver assembly (for Radio and Display Type) when the engine switch is on (ACC), 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more. |
·
Harness or connector ·
Navigation receiver assembly (for Navigation Receiver Type) ·
radio and display receiver assembly (for Radio and Display Type) ·
Combination meter assembly |
When replacing the combination meter assembly, make sure to replace it with a new one.
Check for DTCs.
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Navigation Receiver Type)>DTC CHECK / CLEAR
for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Navigation Receiver Type) | B |
| NG (for Radio and Display Type) | C |
A
B
C
Disconnect the G16 combination meter assembly connector.
Disconnect the F4 navigation receiver assembly connector.(for Navigation Receiver Type)
Disconnect the F40 radio and display receiver assembly connector.(for Radio and Display Type)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-38(MSCH) - F4-3(CNH1) | Always | Below 1 Ω |
| G16-37(MSCL) - F4-4(CNL1) | Always | Below 1 Ω |
| G16-38(MSCH) or F4-3(CNH1) - Body ground | Always | 10 kΩ or higher |
| G16-37(MSCL) or F4-4(CNL1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-38(MSCH) - F40-3(CNH1) | Always | Below 1 Ω |
| G16-37(MSCL) - F40-4(CNL1) | Always | Below 1 Ω |
| G16-38(MSCH) or F40-3(CNH1) - Body ground | Always | 10 kΩ or higher |
| G16-37(MSCL) or F40-4(CNL1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Turn the engine switch on (IG) and wait 30 seconds.
A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and navigation receiver assembly.(for Navigation Receiver Type)
A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and radio and display receiver.(for Radio and Display Type)
| *a | Multi-information Display |
| *b | Audio Tab |
Operate the steering pad switch assembly and check that the audio tab illuminates.
Check for DTCs.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR
The audio tab illuminates and DTC B150A is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Navigation Receiver Type) | B |
| NG (for Radio and Display Type) | C |
A
B
C
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL