The ECM sends and receives data to and from the nitrogen oxides sensor via local CAN communication.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Turn the engine switch on (IG) and wait for 1.6 seconds or more. | Communication stops between the ECM and the nitrogen oxides sensor for 1.6 seconds or more.
(1 trip detectionlogic) |
·
Nitrogen oxides sensor ·
Harness or connector ·
ECM |
The ECM stores a DTC when a communication malfunction occurs between the nitrogen oxides sensor and ECM.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
According to the display on the GTS, select "Health Check".
Check for currently output system DTCs.
| Result | Proceed to |
|---|---|
| DTC U029D is output | A |
| DTC U029D and other DTCs are output* | B |
*If any other DTCs are output, perform troubleshooting for those DTCs first.
A
B
Disconnect the nitrogen oxides sensor connector.
Turn the engine switch on (IG).
| *1 | Front view of wire harness connector
(to Nitrogen oxides sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| s6-1 (BATT) - s6-2 (GND) | Engine switch on (IG) | 11 to 14 V |
OK
NG
Disconnect the nitrogen oxides sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| s6-4 (CAN+) - G184-27 (CANU) | Always | Below 1 Ω |
| s6-3 (CAN-) - G184-35 (CAND) | Always | Below 1 Ω |
| s6-4 (CAN+) or G184-27 (CANU) - Body ground and other terminals | Always | 10 kΩ or higher |
| s6-3 (CAN-) or G184-35 (CAN-) - Body ground and other terminals | Always | 10 kΩ or higher |
OK
NG
Replace the nitrogen oxides sensor (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds.
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG) wait for 1.6 seconds or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| DTC U029D is output | B |
A
B
Inspect NOx PM relay (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the nitrogen oxides sensor connector.
Remove the NOx PM relay from the engine relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| s6-1 (BATT) - NOx PM relay terminal 3 | Always | Below 1 Ω |
| s6-2 (GND) - Body ground | Always | Below 1 Ω |
| NOx PM relay terminal 2 - Body ground | Always | Below 1 Ω |
| NOx PM relay terminal 3 or s6-1 (BATT) - Body ground and other terminals | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| NOx PM relay terminal 5 - Body ground | Always | 11 to 14 V |
OK
NG