Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  


DESCRIPTION

Refer to DTCs C1421, C1423 and C1424 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>C1421).

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PMC terminal voltage is higher than 0.86 V for 5 seconds or more while the vehicle is being driven at a speed of 3 km/h (2mph) or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch assembly circuit

·

Master cylinder pressure sensor circuit

·

Brake actuator assembly (Master cylinder pressure sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1422, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>C1425).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)

OK

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

NG

4.CHECK TERMINAL VOLTAGE AND RESISTANCE (STOP LIGHT SWITCH ASSEMBLY POWER SOURCE TERMINAL)
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Vacuum Brake Booster)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch assembly installation are normal.




OK

3.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1422 is not output A
DTC C1422 is output B



A

B

4.CHECK TERMINAL VOLTAGE AND RESISTANCE (STOP LIGHT SWITCH ASSEMBLY POWER SOURCE TERMINAL)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.

Disconnect the A99 stop light switch assembly connector.


c.
E361512E01
1.49,0.25 1.896,0.51 0.406,0.26 1.333,1.177 1.177,1.771 true 2.26,1.135 2.792,1.135 true 0.177,0.146 0.49,0.302 0.313,0.156 10 false *a 1.563,0.281 1.875,0.438 0.313,0.156 10 false A99 1.021,1.813 1.438,2.01 0.417,0.198 10 false GND 2.854,1.042 3.167,1.198 0.313,0.156 10 false B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-7(B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK TERMINAL VOLTAGE (STP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (STP)

OK

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY- BRAKE ACTUATOR ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY- BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the A99 stop light switch assembly connector.


b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-1 (OUT) - A6-2 (STP) Always Below 1 Ω
A99-1 (OUT) or A6-2 (STP) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR