Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1501  Sub Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a No. 2 fuel sender gauge assembly malfunction via a direct line.

DTC Code DTC Detection Condition Trouble Area
B1501 Both conditions are met:
·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.

·

Average input signal of fuel sender gauge is 630 Ω or more 3 times consecutively.


·

Harness or connector

·

Combination meter assembly

·

Fuel tank vent tube assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

except 5L-E
E380648E03
0.615,2.792 2.531,3.125 1.917,0.333 10 false Fuel Sender Gauge Assembly NO.2 0.521,3.542 3.052,3.729 2.531,0.188 10 false Fuel Tank Vent Tube Sub-assembly 3.896,4.021 5.813,4.302 1.917,0.281 10 false Combination Meter Assembly 3.896,3.833 5.813,4.115 1.917,0.281 10 false G304 0.521,3.365 3.052,3.552 2.531,0.188 10 false t1 2.271,1.927 2.583,2.156 0.313,0.229 10 false FR2 2.25,2.427 2.594,2.667 0.344,0.24 10 false FE2 2.229,1.469 2.688,1.677 0.458,0.208 10 false FV2 3.979,1.469 4.333,1.719 0.354,0.25 10 false L 3.958,1.906 4.302,2.146 0.344,0.24 10 false FR 3.938,2.417 4.469,2.667 0.531,0.25 10 false FE 3.708,1.469 4.167,1.677 0.458,0.208 10 false 25 3.698,1.927 4.156,2.135 0.458,0.208 10 false 26 3.771,2.427 4.229,2.635 0.458,0.208 10 false 2 2.625,1.448 3.083,1.656 0.458,0.208 10 false 5 2.625,1.896 3.083,2.104 0.458,0.208 10 false 4 2.625,2.406 3.083,2.615 0.458,0.208 10 false 1 1.823,1.563 2.281,1.771 0.458,0.208 10 false 3 1.833,2.5 2.292,2.708 0.458,0.208 10 false 2 1.823,2.042 2.281,2.25 0.458,0.208 10 false 1

for 5L-E
E321084E14
5.177,0.781 5.385,1.042 0.208,0.26 10 false L 5.177,1.406 5.458,1.677 0.281,0.271 10 false TE 5.021,3.906 5.344,4.125 0.323,0.219 10 false G6 5.177,3.25 5.49,3.479 0.313,0.229 10 false ET 4.917,3.25 5.167,3.5 0.25,0.25 10 false 5 4.979,0.823 5.188,1.083 0.208,0.26 10 false 8 4.906,1.396 5.135,1.677 0.229,0.281 10 false 23 3.5,0.813 3.677,1.073 0.177,0.26 10 false 4 3.5,1.406 3.708,1.667 0.208,0.26 10 false 5 5.031,4.094 6.875,4.333 1.844,0.24 10 false Combination Meter Assembly 2.771,1.396 2.938,1.646 0.167,0.25 10 false 2 1.635,1.417 1.906,1.74 0.271,0.323 10 false 1 1.01,2.417 1.323,2.646 0.313,0.229 10 false t1 1,2.615 3.438,2.896 2.438,0.281 10 false Fuel Tank Vent Tube Sub-assembly 1.135,1.833 3.51,2.042 2.375,0.208 10 false Fuel Sender Gauge Assembly NO.2 3.135,1.406 3.458,1.635 0.323,0.229 10 false FV2 3.135,0.813 3.469,1 0.333,0.188 10 false FR2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0, Max.: 127.5 Current fuel level displayed Unit: L


Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except 5L-E A
for 5L-E B



A

3.CHECK FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)

B

8.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
3.CHECK FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
E284677C67
1.5,0.208 1.906,0.458 0.406,0.25 2.5,1.667 2.333,1.667 2.333,1.667 2.24,1.125 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.542,0.25 1.969,0.448 0.427,0.198 10 false G304 2.542,1.583 2.854,1.74 0.313,0.156 10 false L
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-25 (L) - Body ground Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.CHECK FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK FUEL SENDER GAUGE ASSEMBLY
E284677C68
1.5,0.208 1.906,0.458 0.406,0.25 2.146,1.104 1.01,1.615 true 2.552,0.99 2.708,1.615 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.542,0.25 2,0.49 0.458,0.24 10 false G304 2.542,1.656 3.052,1.865 0.51,0.208 10 false FE 0.802,1.635 1.115,1.792 0.313,0.156 10 false FR
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G304-26 (FR) - G304-2 (FE) Engine switch on (IG) 0.2 to 4.7 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the t1 fuel tank vent tube assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - G304-26 (FR) Always Below 1 Ω
2t1-1 (FE) - G304-3 (FE) Always Below 1 Ω
t1-5 (FV2) - G304-25 (L) Always Below 1 Ω
G304-26 (FR) - Body ground Always 10 kΩ or higher
G304-2 (FE) - Body ground Always 10 kΩ or higher
G304-25 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2

OK

7.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

7.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E380660C01
1.688,2.74 2.094,2.969 0.406,0.229 0.833,2.583 0.667,2.583 0.667,2.583 1.688,1.104 true 1.5,2.333 1.313,2.333 1.313,2.333 1.865,1.073 true 2.083,1.917 1.833,1.917 1.833,1.917 2.063,1.083 true 1.594,0.375 1.906,0.573 0.313,0.198 10 false *a 0.906,2.479 1.219,2.677 0.313,0.198 10 false 1 1.573,2.25 1.885,2.448 0.313,0.198 10 false 2 2.156,1.833 2.469,2.031 0.313,0.198 10 false 3 0.188,2.99 0.5,3.188 0.313,0.198 10 false *b 1.813,2.781 2.125,2.979 0.313,0.198 10 false t1
*a Fuel Tank Vent Tube Assembly
*b Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-1 (FE2) - 2 Always Below 1 Ω
t1-4 (FR2) - 1 Always Below 1 Ω
t1-5 (FV2) - 3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

8.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the t1 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-8 (L) - t1-4 (FR2) Always Below 1 Ω
G6-23 (FE) - t1-5 (FV2) Always Below 1 Ω
G6-5 (ET) - Body ground Always Below 1 Ω
G6-8 (L) or t1-4 (FR2) - Body ground Always 10 kΩ or higher
G6-23 (FE) or t1-5 (FV2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FUEL SENDER GAGE ASSEMBLY NO.2
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

10.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E349680C02
1.5,2.813 1.906,3.021 0.406,0.208 1.698,1.802 1.698,0.844 false 2.094,1.802 2.094,0.833 false 0.688,4.292 0.844,4.292 0.844,4.292 1.563,3.979 false 2.75,4.313 2.594,4.313 2.594,4.313 1.802,3.979 false 0.635,0.104 0.948,0.302 0.313,0.198 10 false *a 1.656,1.844 1.813,2.042 0.156,0.198 10 false 1 2.063,1.844 2.219,2.042 0.156,0.198 10 false 2 0.948,3.021 1.26,3.219 0.313,0.198 10 false *b 0.406,4.219 0.917,4.479 0.51,0.26 10 false FV2 2.813,4.229 3.25,4.417 0.438,0.188 10 false FR2 1.646,2.833 1.865,3.073 0.219,0.24 10 false t1
*a Fuel Tank Vent Tube Assembly
*b Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
t1-4 (FR2) - 1 Always Below 1 Ω
t1-5 (FV2) - 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY