The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are deactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated when the engine switch is turned on (IG). The MIL goes off when the engine is started.
For the circuit diagram of the ECM power source refer to the ECM power source circuit.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit
VC Power Source Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Turn the engine switch on (IG).
| *A | for Automatic Transmission |
| *B | for Manual Transmission |
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G55-23 (+B) - C36-12 (E1) | Engine switch on (IG) | 11 to 14 V |
| G55-22 (+B2) - C36-12 (E1) | Engine switch on (IG) | 11 to 14 V |
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle body with motor assembly connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
for Automatic Transmission
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
A
B
Disconnect the accelerator pedal sensor assembly connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for intake side of bank 1) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for intake side of bank 2) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for exhaust side of bank 1) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| MIL does not illuminate | A |
| MIL illuminates | B |
A
B
Disconnect the VVT sensor (for exhaust side of bank 2) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the power steering oil pressure switch connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible (for Automatic Transmission) | A |
| Communication is not possible (for Manual Transmission) | B |
| Communication is possible | C |
A
B
C
Disconnect the emission control valve set connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the No. 2 emission control valve set connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the VVT sensor (for intake side of bank 1) connector.
Disconnect the VVT sensor (for intake side of bank 2) connector.
Disconnect the VVT sensor (for exhaust side of bank 1) connector.
Disconnect the VVT sensor (for exhaust side of bank 2) connector.
Disconnect the emission control valve set connector.
Disconnect the No. 2 emission control valve set connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-6 (VCPA) - Body ground | Always | 10 kΩ or higher |
| G56-3 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C36-2 (VCTA) - Body ground | Always | 10 kΩ or higher |
| C35-13 (VCAP) - Body ground | Always | 10 kΩ or higher |
| C34-12 (VCV1) - Body ground | Always | 10 kΩ or higher |
| C34-6 (VCV2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the VVT sensor (for intake side of bank 1) connector.
Disconnect the VVT sensor (for intake side of bank 2) connector.
Disconnect the VVT sensor (for exhaust side of bank 1) connector.
Disconnect the VVT sensor (for exhaust side of bank 2) connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-4 (VCPA) -Body ground | Always | 10 kΩ or higher |
| G56-2 (VCP2) -Body ground | Always | 10 kΩ or higher |
| C36-13 (VCTA) -Body ground | Always | 10 kΩ or higher |
| C34-15 (VCV1) -Body ground | Always | 10 kΩ or higher |
| C34-16 (VCV2) -Body ground | Always | 10 kΩ or higher |
| C88-18 (VCV2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C89-23 (VC) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG