While the engine is being cranked, current flows from terminal ST1 of the ignition switch to the park/neutral position switch (for automatic transmission) or clutch start switch (for manual transmission) and also flows to terminal STA of the ECM (STA Signal).
Refer to DTC P0617 (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>P0617).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
This chart is based on the premise that the engine can be cranked normally. If the engine does not crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).
Confirm the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/o Entry and Start System | A |
| w/ Entry and Start System | B |
A
B
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
OK
NG
Remove the ST relay from the engine room relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 2 - Body ground | Engine cranking | 11 to 14 V |
The engine does not crank because the relay is not installed.
| *1 | Engine Room Relay Block Assembly |
| *2 | ST Relay |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Manual Transmission Models) | B |
| NG (for Automatic Transmission Models) | C |
A
B
C
Inspect the ST relay (See pageEngine / Hybrid System>2TR-FE (STARTING)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the ST relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 1 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for Manual Transmission Models) | A |
| OK (for Automatic Transmission Models) | B |
| NG | C |
A
B
C
Remove the ST relay from the engine room relay block assembly.
Disconnect the clutch start switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 2 - A40-1 | Always | Below 1 Ω |
| ST relay terminal 2 - C154-17 (STA) | Always | Below 1 Ω |
| ST relay terminal 2, A40-1 or C154-17 (STA) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the clutch start switch assembly (See page)Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION.
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-1 (ST1) - A40-2 | Always | Below 1 Ω |
| G2-1 (ST1) or A40-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the ignition switch assembly (Engine / Hybrid System>2TR-FE (STARTING)>IGNITION SWITCH>INSPECTION).
OK
NG
Remove the ST relay from the engine room relay block assembly.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C159-5 (L) - ST relay terminal 2 | Always | Below 1 Ω |
| C154-17 (STA) - ST relay terminal 2 | Always | Below 1 Ω |
| C159-5 (L), C154-17 (STA) or ST relay terminal 2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the park/neutral position switch assembly (See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
OK
NG
(See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Disconnect the park/neutral position switch assembly connector.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G2-1 (ST1) - C159-4 (B) | Always | Below 1 Ω |
| G2-1 (ST1) - C154-15 (NSW) | Always | Below 1 Ω |
| G2-1 (ST1), C159-4 (B) or C154-15 (NSW) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the ignition switch assembly (See pageEngine / Hybrid System>2TR-FE (STARTING)>IGNITION SWITCH>INSPECTION).
OK
NG
Connect the GTS to DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Starter Signal.
Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
|---|---|
| ON | OFF |
| START | ON |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the park/neutral position switch assembly (See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
OK
NG
(See pageDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Remove the ST relay from the engine room relay block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 2 - C159-5(L) | Always | Below 1 Ω |
| ST relay terminal 2 - C154-17 (STA) | Always | Below 1 Ω |
| ST relay terminal 2, C159-5 (L) or C154-17 (STA) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G213-10 (STAR) - C159-4 (B) | Always | Below 1 Ω |
| G213-10 (STAR) - C154-15 (NSW) | Always | Below 1 Ω |
| G213-10 (STAR), C159-4 (B) or C154-15 (NSW) - Body ground | Always | 10 kΩ or higher |
OK
NG