Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2017.08–2020.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B1247 Tire Pressure Monitor Receiver Communication Stop In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


This DTC is for main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C269187E41
0.25,3.135 2.958,3.344 2.708,0.208 10 false Tire Pressure Warning ECU and Receiver 5.385,2.99 7.042,3.344 1.656,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 1.313,0.75 1.51,0.896 0.198,0.146 10 false IG 5.688,1.323 6.094,1.688 0.406,0.365 10 false RDA 5.698,1.833 6.021,1.99 0.323,0.156 10 false PRG 5.469,1.688 5.656,1.906 0.188,0.219 10 false 5 5.448,1.177 5.688,1.406 0.24,0.229 10 false 4 1.594,0.615 1.688,0.75 0.094,0.135 10 false 1 1.594,1.177 1.792,1.458 0.198,0.281 10 false 4 1.594,1.698 1.865,2.031 0.271,0.333 10 false 5 1.167,2.396 1.5,2.552 0.333,0.156 10 false GND 1.583,2.26 1.823,2.49 0.24,0.229 10 false 12 3.885,0.75 5.438,0.896 1.552,0.146 10 false from IG Circuit 5.385,2.833 5.833,3 0.448,0.167 10 false G218 2.25,0.917 3.26,1.125 1.01,0.208 10 false ECU-IG NO.1 1.177,1.323 1.75,1.688 0.573,0.365 10 false RDA 1.177,1.833 1.771,2.292 0.594,0.458 10 false PRG 0.25,2.948 0.708,3.146 0.458,0.198 10 false R41

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

Click here

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the R41 tire pressure warning ECU and receiver connector.


b.

Disconnect the G218 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-4 (RDA) - G218-4 (RDA) Always Below 1 Ω
R41-4 (RDA) or G218-4 (RDA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
a.
C375025C13
0.281,0.917 0.677,1.177 0.396,0.26 1.229,1.229 0.667,1.448 true 2.219,1.469 2.75,1.771 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.417,1.385 0.729,1.583 0.313,0.198 10 false IG 2.792,1.708 3.25,1.906 0.458,0.198 10 false GND 0.333,0.969 0.792,1.167 0.458,0.198 10 false R41
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-12 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R41-1 (IG) - Body ground Ignition switch ON 10 to 16 V



Result:
Proceed to
OK
NG



OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1247 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)