Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2017.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2179  Tire Pressure Monitor ECU Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) sends signals to the tire pressure warning ECU and receiver via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2179 Tire Pressure Monitor ECU Communication Stop Communication between the main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver is interrupted for 10 seconds or more.
·

Main body ECU (Multiplex network body ECU)

·

Harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C257851E67
2.177,0.646 2.573,0.865 0.396,0.219 10 false PRG 2.583,0.5 2.875,0.76 0.292,0.26 10 false 5 4.469,0.521 4.635,0.688 0.167,0.167 10 false 5 4.365,1.406 7.021,1.583 2.656,0.177 10 false Tire Pressure Warning ECU and Receiver 0.24,1.198 0.667,1.354 0.427,0.156 10 false G218 0.26,1.385 3.292,1.719 3.031,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 4.646,0.635 5.188,0.99 0.542,0.354 10 false PRG 4.354,1.208 5.458,1.417 1.104,0.208 10 false R41

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the R41 tire pressure warning ECU and receiver connector.


b.

Disconnect the G218 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-5 (PRG) - G218-5 (PRG) Always Below 1 Ω
R41-5 (PRG) or G218-5 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

OK:

DTC C2179 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)