Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0332058 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a lane departure alert main switch signal from the steering pad switch assembly and sends the signal to the forward recognition camera via CAN communication.

WIRING DIAGRAM

C385635E02
0.156,2.344 2.76,2.542 2.604,0.198 10 false Steering Pad Switch Assembly 2.25,1.698 3.167,2.063 0.917,0.365 10 false Spiral Cable Sub-assembly 4.417,1.729 5.438,2.146 1.021,0.417 10 false Driving Support ECU Assembly 4.719,3.417 5.125,3.583 0.406,0.167 10 false ECM 5.854,1.74 7.094,2.083 1.24,0.344 10 false Forward Recognition Camera 0.604,1.333 1.75,1.75 1.146,0.417 10 false Lane Departure Alert Main Switch 5.844,1.594 6.302,1.792 0.458,0.198 10 false W22 4.406,1.573 4.865,1.771 0.458,0.198 10 false G224 4.51,2.844 5.104,3.01 0.594,0.167 10 false ECCS 0.917,0.76 1.375,0.958 0.458,0.198 10 false 240 Ω 3.156,0.604 3.542,0.792 0.385,0.188 10 false G208 3.167,1.208 3.625,1.406 0.458,0.198 10 false G208 4.604,3.26 5.198,3.427 0.594,0.167 10 false G181 6.208,0.823 6.823,1.021 0.615,0.198 10 false CANL 6.208,1.219 6.823,1.417 0.615,0.198 10 false CANH 4.844,1.229 5.458,1.427 0.615,0.198 10 false CA1P 4.833,0.823 5.448,1.021 0.615,0.198 10 false CA1N 5.979,0.656 6.292,0.854 0.313,0.198 10 false 12 5.302,1.063 5.458,1.26 0.156,0.198 10 false 8 6.042,1.063 6.198,1.26 0.156,0.198 10 false 6 5.302,0.656 5.458,0.854 0.156,0.198 10 false 9 4.25,2.729 4.563,2.927 0.313,0.198 10 false 21 3.25,0.375 3.563,0.573 0.313,0.198 10 false 12 3.292,0.99 3.604,1.188 0.313,0.198 10 false 2 2.063,1 2.375,1.198 0.313,0.198 10 false 7 2.052,0.385 2.365,0.583 0.313,0.198 10 false 4 2.552,0.49 3.167,0.688 0.615,0.198 10 false DIST 2.552,1.094 3.01,1.292 0.458,0.198 10 false ECC 0.635,3.323 2.583,3.479 1.948,0.156 10 false : CAN Communication Line 0.51,3.042 3.719,3.24 3.208,0.198 10 false *2: for 2TR-FE 0.51,2.74 3.719,2.938 3.208,0.198 10 false *1: except 2TR-FE 3.313,2.958 3.625,3.156 0.313,0.198 10 false *1 4.073,2.958 4.385,3.156 0.313,0.198 10 false *2 4.5,0.604 5.115,0.802 0.615,0.198 10 false SPSW 4.25,0.479 4.5,0.646 0.25,0.167 10 false 23 2,0.604 2.458,0.802 0.458,0.198 10 false z16 2,1.208 2.458,1.406 0.458,0.198 10 false z16

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Can Bus Check.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (HEALTH CHECK)

B

2.CHECK FOR DTCs (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


Result:
Result Proceed to
No DTCs are output. A
DTCs are output. B



A

3.INSPECT STEERING PAD SWITCH ASSEMBLY

B

GO TO DTC CHART

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the G224 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G208-12 (DIST) - G224-23 (SPSW) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G208-12 (DIST) or G224-23 (SPSW) - Body ground Always 10 kΩ or higher



d.

Reconnect the G224 driving support ECU assembly connector.


e.

Reconnect the G208 spiral cable sub-assembly connector.


Result:
Proceed to
OK (for 2TR-FE)
OK (except 2TR-FE)
NG



OK (for 2TR-FE)

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

OK (except 2TR-FE)

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Disconnect the G181 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G208-2 (ECC) - G181-21 (ECCS) Always Below 1 Ω



d.

Reconnect the G208 spiral cable sub-assembly connector.


e.

Reconnect the G181 ECM connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the G208 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G208-2 (ECC) - Body ground Always Below 1 Ω



c.

Reconnect the G208 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR