Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › from 2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1746  Gate Solenoid Valve Circuit  


DESCRIPTION

The suspension control ECU opens the gate solenoid valve (No. 2 height control valve) to allow compressed air to flow into the height control cylinder (pneumatic cylinder) and raise the vehicle height.

The gate solenoid valve (No. 2 height control valve) opens and closes the passage between the right and left height control cylinders (pneumatic cylinders).

The No. 2 height control valve consists of a leveling solenoid valve and a gate solenoid valve.

The gate solenoid valve opens and closes the passage between the height control compressor and the height control cylinder (pneumatic cylinder).

DTC Code DTC Detection Condition Trouble Area
C1746 Either condition is met:
·

With the height control valve inactivated, an open signal of the height control valve is detected for 1 second or more.

·

With the height control valve activated, a short signal of the valve is detected 8 times successively.


·

Harness or connector

·

Gate solenoid valve (No. 2 height control valve)

·

Suspension control ECU



HINT:
·

Once the suspension control ECU stores DTC C1746 in memory, vehicle height control is suspended until a normal signal is input to the suspension control ECU from the height control valves. However, control is resumed if the ignition switch is turned off and then to ON again.

·

Malfunction in the gate solenoid valve:

Height control operation is suspended and the height control indicator does not change by operating the height control switch.



WIRING DIAGRAM

C216269E21
0.438,1.896 2.625,2.26 2.188,0.365 10 false Gate Solenoid Valve (No. 2 Height Control Valve) 5.396,1.542 7.094,1.76 1.698,0.219 10 false Suspension Control ECU 1.021,0.708 1.323,0.927 0.302,0.219 10 false LH+ 1.125,1.24 1.323,1.458 0.198,0.219 10 false E 1.417,0.604 1.594,0.781 0.177,0.177 10 false 1 1.427,1.135 1.604,1.313 0.177,0.177 10 false 2 5.563,0.604 5.74,0.781 0.177,0.177 10 false 15 5.875,0.781 6.271,0.99 0.396,0.208 10 false SLRL 5.417,1.375 5.698,1.542 0.281,0.167 10 false A14 0.458,1.729 0.656,1.896 0.198,0.167 10 false S7

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


HINT:

If DTC C1782 is output at the same time as C1746, perform the inspection necessary for DTC C1782 first (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (REAR GATE SOLENOID)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Air suspension / Active Test.

Air Suspension
Tester Display Test Part Control Range Diagnostic Note
Rear Gate Solenoid Gate solenoid valve ON or OFF
·

The operating sound of the solenoid (clicking sound) can be heard.

·

When the Active Test is performed, Rear Gate Solenoid in the Data List changes between ON and OFF accordingly.



OK:

Operation of solenoid (clicking sound) can be heard.


Result
Result Proceed to
NG A
OK (When troubleshooting according to problem symptoms table) B
OK (When troubleshooting according to DTC chart) C



A

2.CHECK HARNESS AND CONNECTOR (GATE SOLENOID VALVE - SUSPENSION CONTROL ECU)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

2.CHECK HARNESS AND CONNECTOR (GATE SOLENOID VALVE - SUSPENSION CONTROL ECU)
a.

Disconnect the S7 gate solenoid valve connector.


b.

Disconnect the A14 suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S7-1 (LH+) - A14-15 (SLRL) Always Below 1 Ω
S7-1 (LH+) - Body ground Always 10 kΩ or higher
S7-2 (E) - Body ground Always Below 1 Ω




OK

3.INSPECT NO. 2 HEIGHT CONTROL VALVE (GATE SOLENOID VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 2 HEIGHT CONTROL VALVE (GATE SOLENOID VALVE)
a.

Turn the ignition switch off.


b.

Remove the No. 2 height control valve (See page Suspension>SUSPENSION CONTROL>CONTROL VALVE ASSEMBLY>REMOVAL).


c.
C214512E17
1.979,1.25 2.271,1.813 false 1.677,1.25 1.396,1.792 false 0.063,0.063 0.365,0.271 0.302,0.208 10 false *a 2.198,1.823 2.51,2.021 0.313,0.198 10 false LH+ 1.323,1.823 1.531,2.01 0.208,0.188 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (LH+) - 2 (E) 20°C (68°F) 17.5 to 21.5 Ω


Text in Illustration
*a Component without harness connected
(No. 2 Height Control Valve)


d.

Connect the positive (+) lead of the battery to terminal 1 (LH+) and the negative (-) lead to terminal 2 (E) of the solenoid valve connector. Then check that the valve makes an operating sound.

OK:

Operation of solenoid (clicking sound) can be heard.




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE NO. 2 HEIGHT CONTROL VALVE ASSEMBLY