Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2017.08–2020.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1791  Adaptive Variable Suspension(AVS) Switch Circuit  


DESCRIPTION

The absorber control switch is used to select the damping force mode of the shock absorber.

DTC Code DTC Detection Condition Trouble Area
C1791 The absorber control switch signal does not change.
·

Absorber control switch (Suspension control switch)

·

Harness or connector

·

Suspension control ECU

·

Shift position indicator



HINT:

This DTC is stored only during test mode.


WIRING DIAGRAM

C384723E02
5.281,1.844 6.865,2.448 1.583,0.604 10 false Suspension Control ECU 5.677,1.292 6.156,1.594 0.479,0.302 10 false TSW2 5.677,0.583 6.156,0.885 0.479,0.302 10 false TSW1 5.385,0.448 5.615,0.719 0.229,0.271 10 false 23 5.406,1.094 5.635,1.365 0.229,0.271 10 false 22 5.271,1.656 5.552,1.917 0.281,0.26 10 false A49 3.031,2.25 3.406,2.51 0.375,0.26 10 false G303 3.417,2.24 5.167,2.552 1.75,0.313 10 false Shift Position Indicator 1,2.208 2.865,2.604 1.865,0.396 10 false Absorber Control Switch (Suspension Control Switch) 4.094,1.115 4.5,1.313 0.406,0.198 10 false ECU2 4.083,0.479 4.49,0.677 0.406,0.198 10 false ECU1 4.604,0.448 4.833,0.656 0.229,0.208 10 false 9 4.625,1.115 4.854,1.323 0.229,0.208 10 false 8 4.323,1.521 4.563,1.771 0.24,0.25 10 false E 4.594,1.51 4.823,1.719 0.229,0.208 10 false 18

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.INSPECT SUSPENSION CONTROL SWITCH
a.

Remove the absorber control switch (suspension control switch) (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.

Inspect the absorber control switch (suspension control switch) (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>INSPECTION).


Result
Result Proceed to
Absorber control switch (suspension control switch) is normal A
Absorber control switch (suspension control switch) is abnormal B


A

2.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - SUSPENSION CONTROL ECU)

B

REPLACE SUSPENSION CONTROL SWITCH

2.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - SUSPENSION CONTROL ECU)
a.

Disconnect the G303 absorber control switch (suspension control switch) connector.


b.

Disconnect the A49 suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G303-9 (ECU1) - A49-23 (TSW1) Always Below 1 Ω
G303-8 (ECU2) - A49-22 (TSW2) Always Below 1 Ω
G303-18 (E) - Body ground Always Below 1 Ω
G303-9 (ECU1) or A49-23 (TSW1) - Body ground Always 10 kΩ or higher
G303-8 (ECU2) or A49-22 (TSW2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT SHIFT POSITION INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT POSITION INDICATOR
a.

Disconnect the A49 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-22 (TSW2) - Body ground Absorber control switch (COMF) pressed and held Below 1 Ω
Absorber control switch (COMF) released 10 kΩ or higher
A49-23 (TSW1) - Body ground Absorber control switch (SPORT) pressed and held Below 1 Ω
Absorber control switch (SPORT) released 10 kΩ or higher




OK

REPLACE SUSPENSION CONTROL ECU

NG