Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › from 2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1792  Height Control Switch Circuit  


DESCRIPTION

The vehicle height can be adjusted by pressing the height control switch.

By pressing the "up" side, vehicle height is raised.

By pressing the "down" side, vehicle height is lowered.

DTC Code DTC Detection Condition Trouble Area
C1792 The height control switch signal does not change.
·

Height control switch (combination switch assembly)

·

Harness or connector

·

Suspension control ECU



HINT:

This DTC is stored only during test mode.


WIRING DIAGRAM

C218601E09
5.208,1.938 6.813,2.125 1.604,0.188 10 false Suspension Control ECU 2.49,1.625 2.896,1.813 0.406,0.188 10 false G156 3.792,1.125 3.927,1.313 0.135,0.188 10 false 7 3.792,0.469 3.927,0.656 0.135,0.188 10 false 6 5.385,1.125 5.594,1.313 0.208,0.188 10 false 14 5.385,0.469 5.594,0.656 0.208,0.188 10 false 15 5.688,1.24 6.167,1.427 0.479,0.188 10 false DNSW 5.688,0.573 6.167,0.76 0.479,0.188 10 false UPSW 2.667,0.792 2.813,0.979 0.146,0.188 10 false E 3.521,0.458 3.708,0.646 0.188,0.188 10 false HI 2.906,0.646 3.229,0.833 0.323,0.188 10 false Up 3.49,1.125 3.708,1.313 0.219,0.188 10 false LO 2.792,1.198 3.198,1.469 0.406,0.271 10 false Down 2.385,0.792 2.615,0.979 0.229,0.188 10 false 24 2.49,1.802 4.563,2.281 2.073,0.479 10 false Height Control Switch (Combination Switch Assembly) 5.208,1.792 5.51,1.979 0.302,0.188 10 false A49

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.READ VALUE USING GTS (HEIGHT CONTROL SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Control Switch (UP) Height control switch ("up" side) / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed
-
Height Control Switch (DOWN) Height control switch ("down" side) / ON or OFF ON: Switch is pressed and held
OFF: Switch is not pressed
-


f.

Check that the value displayed on the GTS changes by pressing the height control switch "up" side or "down" side.

OK:

Height control switch value changes.




OK

NG

2.INSPECT COMBINATION SWITCH ASSEMBLY
2.INSPECT COMBINATION SWITCH ASSEMBLY
a.

Remove the height control switch (combination switch assembly) (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL SWITCH>REMOVAL).


b.

Inspect the height control switch (combination switch assembly) (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL OFF SWITCH>INSPECTION).

Result
Result Proceed to
Height control switch (combination switch assembly) is normal A
Height control switch (combination switch assembly) is abnormal B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - SUSPENSION CONTROL ECU)

B

REPLACE COMBINATION SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - SUSPENSION CONTROL ECU)
a.

Disconnect the G156 height control switch (combination switch assembly) connector.


b.

Disconnect the A49 suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-6 (HI) - A49-15 (UPSW) Always Below 1 Ω
G156-7 (LO) - A49-14 (DNSW) Always Below 1 Ω
G156-24 (E) - Body ground Always Below 1 Ω
G156-6 (HI) or A49-15 (UPSW) - Body ground Always 10 kΩ or higher
G156-7 (LO) or A49-14 (DNSW) - Body ground Always 10 kΩ or higher




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR