This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1686 | Side camera feedback malfunction | ·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly LH (for LHD) ·
Outer rear view mirror assembly LH (for LHD) ·
Side television camera assembly RH (for RHD) ·
Outer rear view mirror assembly RH (for RHD) |
for LHD
for RHD
When "!" mark is displayed on the navigation receiver assembly*1 or radio and display receiver assembly*2 after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>INITIALIZATION
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the multi-terrain monitor system may be needed.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1686 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the I7 parking assist ECU connector.
Disconnect the K11 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| I7-5 (DCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| I7-4 (DCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| I7-3 (DGND) - K11-7 (SGND) | Always | Below 1 Ω |
| I7-2 (DCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| I7-5 (DCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| I7-4 (DCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| I7-3 (DGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (DGND) - Body ground | Always | Below 1 Ω |
| 4 (DCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly LH.
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
| Item | Content |
|---|---|
| Tester Connection | I7-5 (DCV+) - I7-3 (DGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly LH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (SCB+) - K11-6 (SCB+) | Always | Below 1 Ω |
| B-3 (SCV+) - K11-2 (SCV+) | Always | Below 1 Ω |
| B-7 (SCV-) - K11-3 (SCV-) | Always | Below 1 Ω |
| B-5 (SGND) - K11-7 (SGND) | Always | Below 1 Ω |
| B-1 (SCB+) or K11-6 (SCB+) - Body ground | Always | 10 kΩ or higher |
| B-3 (SCV+) or K11-2 (SCV+) - Body ground | Always | 10 kΩ or higher |
| B-7 (SCV-) or K11-3 (SCV-) - Body ground | Always | 10 kΩ or higher |
| B-5 (SGND) or K11-7 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1686 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I7 parking assist ECU connector.
Disconnect the J11 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| I7-5 (DCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| I7-4 (DCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| I7-3 (DGND) - J11-7 (DGND) | Always | Below 1 Ω |
| I7-2 (DCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| I7-5 (DCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| I7-4 (RCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| I7-3 (DGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Parking Assist ECU) |
Disconnect the parking assist ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (DGND) - Body ground | Always | Below 1 Ω |
| 4 (DCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Disconnect the outer rear view mirror assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch on (ACC) | 5.5 to 7.05 V |
| I7-2 (DCB+) - I7-3 (DGND) | Engine switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
| Item | Content |
|---|---|
| Tester Connection | I7-5 (DCV+) - I7-3 (DGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Engine switch on (IG), panoramic view monitor switch (multi-terrain monitor switch) on |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(to Side Television Camera Assembly RH) |
| *b | Component without harness connected
(to Outer Mirror Actuator Assembly RH) |
Disconnect the outer rear view mirror assembly RH connector.
Disconnect the side television camera assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (SCB+) - J11-6 (DCB+) | Always | Below 1 Ω |
| A-3 (SCV+) - J11-2 (DCV+) | Always | Below 1 Ω |
| A-7 (SCV-) - J11-3 (DCV-) | Always | Below 1 Ω |
| A-5 (SGND) - J11-7 (DGND) | Always | Below 1 Ω |
| A-1 (SCB+) or J11-6 (DCB+) - Body ground | Always | 10 kΩ or higher |
| A-3 (SCV+) or J11-2 (DCV+) - Body ground | Always | 10 kΩ or higher |
| A-7 (SCV-) or J11-3 (DCV-) - Body ground | Always | 10 kΩ or higher |
| A-5 (SGND) or J11-7 (DGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>MULTI-TERRAIN MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1686 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG