Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › MULTI-TERRAIN MONITOR SYSTEM › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0328431 MULTI-TERRAIN MONITOR SYSTEM C

PARK ASSIST / MONITORING  MULTI-TERRAIN MONITOR SYSTEM  U0265  Lost Communication with Image Processing Sensor A  U0266  Lost Communication with Image Processing Sensor B  U0267  Lost Communication with Image Processing Sensor C  U0268  Lost Communication with Image Processing Sensor D  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0265 Lost Communication with rear television camera assembly
·

Parking assist ECU

·

Rear television camera assembly

·

CAN junction connector

·

CAN junction terminal

·

CAN main wire or connector

·

CAN branch wire or connector


U0266 Lost Communication with side television camera assembly LH
·

Parking assist ECU

·

Side television camera assembly LH

·

CAN junction connector

·

CAN junction terminal

·

CAN main wire or connector

·

CAN branch wire or connector


U0267 Lost Communication with front television camera assembly
·

Parking assist ECU

·

Front television camera assembly

·

CAN junction connector

·

CAN junction terminal

·

CAN main wire or connector

·

CAN branch wire or connector


U0268 Lost Communication with side television camera assembly RH
·

Parking assist ECU

·

Side television camera assembly RH

·

CAN junction connector

·

CAN junction terminal

·

CAN main wire or connector

·

CAN branch wire or connector



WIRING DIAGRAM

E382443E01
5.75,2.052 6.063,2.25 0.313,0.198 10 false I7 5.729,2.26 7.073,2.531 1.344,0.271 10 false Parking Assist ECU 5.719,1.042 6.031,1.24 0.313,0.198 10 false 21 5.729,1.448 6.042,1.646 0.313,0.198 10 false 20 6.135,1.083 6.719,1.354 0.583,0.271 10 false CANH 6.177,1.656 6.76,1.927 0.583,0.271 10 false CANL 5.729,6.656 6.177,6.896 0.448,0.24 10 false G300 5.708,6.854 7.156,7.156 1.448,0.302 10 false CAN Junction Terminal 5.719,5.719 6.031,5.917 0.313,0.198 10 false 3 5.74,6.167 6.052,6.365 0.313,0.198 10 false 2 6.24,6.229 6.823,6.5 0.583,0.271 10 false CANL 6.229,5.865 6.813,6.135 0.583,0.271 10 false CANH 4.708,4.75 5.156,4.99 0.448,0.24 10 false J11 4.719,4.948 7.073,5.385 2.354,0.438 10 false Outer Rear View Mirror Assembly RH 0.156,4.948 2.646,5.344 2.49,0.396 10 false Outer Rear View Mirror Assembly LH 0.229,4.177 2.323,4.604 2.094,0.427 10 false Side Television Camera Assembly LH 0.24,4.021 0.688,4.26 0.448,0.24 10 false B 4.865,3.906 5.313,4.146 0.448,0.24 10 false A 4.865,4.094 6.958,4.521 2.094,0.427 10 false Side Television Camera Assembly RH 0.177,4.75 0.625,4.99 0.448,0.24 10 false K11 0.385,3.313 0.969,3.583 0.583,0.271 10 false CANH 0.406,3.74 0.99,4.01 0.583,0.271 10 false CANL 0.948,3.177 1.26,3.375 0.313,0.198 10 false 2 0.948,3.604 1.26,3.802 0.313,0.198 10 false 6 6.375,3.333 6.958,3.604 0.583,0.271 10 false CANH 6.385,3.708 6.969,3.979 0.583,0.271 10 false CANL 6.125,3.24 6.438,3.438 0.313,0.198 10 false 2 6.125,3.615 6.438,3.813 0.313,0.198 10 false 6 2.604,3.573 2.917,3.771 0.313,0.198 10 false 5 4.635,3.583 4.948,3.781 0.313,0.198 10 false 5 4.615,3.208 4.927,3.406 0.313,0.198 10 false 1 2.594,3.188 2.906,3.385 0.313,0.198 10 false 1 0.833,1.156 1.417,1.427 0.583,0.271 10 false CANH 0.875,1.583 1.458,1.854 0.583,0.271 10 false CANL 0.167,2.104 2.656,2.5 2.49,0.396 10 false Rear Television Camera Assembly 0.24,1.885 1.052,2.094 0.813,0.208 10 false X10*1, v3*2 1.438,1.479 1.75,1.677 0.313,0.198 10 false 1 1.5,1.031 1.813,1.229 0.313,0.198 10 false 4 0.125,7.313 1.854,7.604 1.729,0.292 10 false *1: w/o Tire Carrier 0.125,7.563 1.854,7.854 1.729,0.292 10 false *2: w/ Tire Carrier 0.177,6.74 2.667,7.135 2.49,0.396 10 false Front Television Camera Assembly 0.198,6.563 0.646,6.802 0.448,0.24 10 false g1 0.76,5.896 1.344,6.167 0.583,0.271 10 false CANH 0.771,6.24 1.354,6.51 0.583,0.271 10 false CANL 1.458,6.177 1.771,6.375 0.313,0.198 10 false 1 1.458,5.75 1.771,5.948 0.313,0.198 10 false 4 4,1.094 4.313,1.292 0.313,0.198 10 false 3 3.979,1.458 4.292,1.656 0.313,0.198 10 false 14 4,5.729 4.313,5.927 0.313,0.198 10 false 5 4.01,6.146 4.323,6.344 0.313,0.198 10 false 16 3.229,5.76 3.542,5.958 0.313,0.198 10 false 7 3.146,6.125 3.458,6.323 0.313,0.198 10 false 18 3.167,3.167 3.479,3.365 0.313,0.198 10 false 6 3.177,3.563 3.49,3.76 0.313,0.198 10 false 17 3.979,3.198 4.292,3.396 0.313,0.198 10 false 2 3.979,3.604 4.292,3.802 0.313,0.198 10 false 13 3.229,1.021 3.542,1.219 0.313,0.198 10 false 4 3.167,1.438 3.479,1.635 0.313,0.198 10 false 15 3.021,6.917 3.469,7.156 0.448,0.24 10 false G292 2.99,7.125 4.844,7.406 1.854,0.281 10 false CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Result:
Result Proceed to
DTC U0265, U0266, U0267, and U0268 are not output. A
DTC U0265 are output. B
DTC U0266 are output. C
DTC U0267 are output. D
DTC U0268 are output. E
DTC U0265, U0266, U0267, and U0268 are output. F



A

B

2.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY BRANCH WIRE)

C

3.CHECK FOR OPEN IN CAN BUS WIRE (OUTER REAR VIEW MIRROR ASSEMBLY LH BRANCH WIRE)

D

5.CHECK FOR OPEN IN CAN BUS WIRE (FRONT TELEVISION CAMERA ASSEMBLY BRANCH WIRE)

E

6.CHECK FOR OPEN IN CAN BUS WIRE (OUTER REAR VIEW MIRROR ASSEMBLY RH BRANCH WIRE)

F

8.CHECK CAN BUS WIRE
2.CHECK FOR OPEN IN CAN BUS WIRE (REAR TELEVISION CAMERA ASSEMBLY BRANCH WIRE)
a.
C346954C25
1.5,0.083 1.906,0.292 0.406,0.208 1.5,0.323 1.906,0.531 0.406,0.208 0.917,1.844 1.083,1.844 1.083,1.844 1.5,1.354 true 0.792,0.583 0.938,0.583 0.938,0.583 1.479,1.094 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.583,0.115 1.896,0.271 0.313,0.156 10 false X10 0.448,1.75 0.938,1.917 0.49,0.167 10 false CANH 0.406,0.5 0.896,0.667 0.49,0.167 10 false CANL 1.625,0.354 1.938,0.51 0.313,0.156 10 false v3 1.938,0.115 2.25,0.271 0.313,0.156 10 false *A 1.938,0.344 2.25,0.5 0.313,0.156 10 false *B
*A w/o Tire Carrier
*B w/ Tire Carrier
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Tire Carrier
Tester Connection Condition Specified Condition
X10-4 (CANH) - X10-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/ Tire Carrier
Tester Connection Condition Specified Condition
v3-4 (CANH) - v3-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

3.CHECK FOR OPEN IN CAN BUS WIRE (OUTER REAR VIEW MIRROR ASSEMBLY LH BRANCH WIRE)
a.
E379398C03
1.469,0.292 1.885,0.573 0.417,0.281 1.906,1.073 2.417,0.75 2.417,0.75 2.583,0.75 true 1.917,1.25 2.333,1.667 2.333,1.667 2.5,1.667 true 1.563,0.354 2.021,0.552 0.458,0.198 10 false K11 2.656,0.698 3.271,0.896 0.615,0.198 10 false CANH 2.615,1.604 3.229,1.802 0.615,0.198 10 false CANL 0.146,0.188 0.458,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K11-1 (CANH) - K11-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK FOR OPEN IN CAN BUS WIRE (SIDE TELEVISION CAMERA ASSEMBLY LH BRANCH WIRE)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS WIRE (SIDE TELEVISION CAMERA ASSEMBLY LH BRANCH WIRE)
a.
E382442C01
1.5,0.344 1.875,0.583 0.375,0.24 1.75,1.083 2.25,0.75 2.25,0.75 2.417,0.75 true 1.75,1.583 2.25,1.917 2.25,1.917 2.417,1.917 true 1.646,0.365 1.802,0.563 0.156,0.198 10 false B 0.135,0.156 0.354,0.365 0.219,0.208 10 false *a 2.5,0.667 3.115,0.865 0.615,0.198 10 false CANH 2.552,1.833 3.167,2.031 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)


Reconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the side television camera assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 (CANH) - B-6 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

5.CHECK FOR OPEN IN CAN BUS WIRE (FRONT TELEVISION CAMERA ASSEMBLY BRANCH WIRE)
a.
C346954C33
1.5,0.323 1.906,0.531 0.406,0.208 0.917,1.844 1.083,1.844 1.083,1.844 1.5,1.354 true 0.792,0.583 0.938,0.583 0.938,0.583 1.479,1.094 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.448,1.75 0.938,1.917 0.49,0.167 10 false CANH 0.406,0.5 0.896,0.667 0.49,0.167 10 false CANL 1.625,0.333 1.979,0.552 0.354,0.219 10 false g1
*a Front view of wire harness connector
(to Rear Television Camera Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the front television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-4 (CANH) - g1-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

6.CHECK FOR OPEN IN CAN BUS WIRE (OUTER REAR VIEW MIRROR ASSEMBLY RH BRANCH WIRE)
a.
E379398C04
1.469,0.292 1.885,0.573 0.417,0.281 1.906,1.073 2.417,0.75 2.417,0.75 2.583,0.75 true 1.917,1.25 2.333,1.667 2.333,1.667 2.5,1.667 true 1.563,0.354 2.021,0.552 0.458,0.198 10 false J11 2.656,0.698 3.271,0.896 0.615,0.198 10 false CANH 2.615,1.604 3.229,1.802 0.615,0.198 10 false CANHL 0.146,0.188 0.458,0.385 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J11-1 (CANH) - J11-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK FOR OPEN IN CAN BUS WIRE (SIDE TELEVISION CAMERA ASSEMBLY RH BRANCH WIRE)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

7.CHECK FOR OPEN IN CAN BUS WIRE (SIDE TELEVISION CAMERA ASSEMBLY RH BRANCH WIRE)
a.
E382442C02
1.5,0.344 1.875,0.583 0.375,0.24 1.75,1.083 2.25,0.75 2.25,0.75 2.417,0.75 true 1.75,1.583 2.25,1.917 2.25,1.917 2.417,1.917 true 1.646,0.365 1.802,0.563 0.156,0.198 10 false A 0.135,0.156 0.354,0.365 0.219,0.208 10 false *a 2.5,0.667 3.115,0.865 0.615,0.198 10 false CANH 2.552,1.833 3.167,2.031 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)


Reconnect the outer rear view mirror assembly RH connector.


b.

Disconnect the side television camera assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (CANH) - A-6 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

8.CHECK CAN BUS WIRE
a.
C216700C25
0.531,2.51 0.958,2.75 0.427,0.24 0.479,0.875 0.917,1.115 0.438,0.24 1.719,0.896 1.375,0.229 1.375,0.229 1.188,0.229 true 1.427,0.885 1.146,0.542 1.146,0.542 1.01,0.542 true 2.146,2.802 2.292,3.083 2.292,3.083 2.469,3.083 true 1.969,0.875 2.104,0.51 2.104,0.51 2.292,0.51 true 0.104,1.958 0.323,2.156 0.219,0.198 10 false *b 0.104,0.073 0.323,0.271 0.219,0.198 10 false *a 0.781,0.156 1.313,0.375 0.531,0.219 10 false CANL 0.583,0.469 1.031,0.667 0.448,0.198 10 false CANH 2.531,3.01 2.844,3.208 0.313,0.198 10 false BAT 0.615,2.552 0.906,2.75 0.292,0.198 10 false G48 0.542,0.917 0.99,1.135 0.448,0.219 10 false G300 2.344,0.438 2.854,0.677 0.51,0.24 10 false E
*a Component with harness connected
(CAN Junction Terminal)
*b Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Resistance: Malfunction
G300-3 (CANH) - G300-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Below 53 Ω: Short in line
G300-3 (CANH) - G300-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G300-3 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
G300-2 (CANL) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Below 6 kΩ: +B short
G300-3 (CANH) - G300-1 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short
G300-2 (CANL) - G300-1 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Below 200 Ω: Ground short



Result:
Result Proceed to
OK A
NG
- Open in CAN main wire
B
NG
- Short in CAN bus wire
C
NG
- +B short
- Ground short
D



A

9.CHECK FOR DTC

B

10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)

C

15.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR)

D

20.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR)
9.CHECK FOR DTC
a.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION





Result:
Result Proceed to
DTC U0265, U0266, U0267, and U0268 are not output. A
DTC U0265, U0266, U0267, and U0268 are output. B



A

B

10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.
C369126C30
1.531,0.292 1.979,0.531 0.448,0.24 1.583,2.979 1.396,2.979 1.396,2.979 1.198,2.021 true 1.5,0.75 1.323,0.75 1.323,0.75 1.177,1.688 true 1.896,2.677 1.708,2.677 1.708,2.677 1.573,2.01 true 1.885,1 1.708,1 1.708,1 1.573,1.719 true 1.573,0.344 2.031,0.542 0.458,0.198 10 false G292 1.688,2.938 2.271,3.177 0.583,0.24 10 false CANL*b 1.583,0.656 2.26,0.854 0.677,0.198 10 false CANH*b 0.094,0.052 0.552,0.25 0.458,0.198 10 false *a 2.031,2.615 2.615,2.854 0.583,0.24 10 false CANL*c 1.99,0.917 2.667,1.115 0.677,0.198 10 false CANH*c
*a Front view of wire harness connector
(to CAN Junction Connector)
*b to Parking Assist ECU
*c to CAN Junction Terminal


Disconnect the CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G292-3 (CANH) - G292-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Parking assist ECU
G292-5 (CANH) - G292-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN junction terminal



Result:
Result Proceed to
OK A
NG (Parking assist ECU CAN main wire) B
NG (CAN junction terminal CAN main wire) C



A

REPLACE CAN JUNCTION CONNECTOR

B

11.CONNECT CONNECTOR

C

13.CONNECT CONNECTOR
11.CONNECT CONNECTOR
a.

Reconnect the G292 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU - CAN JUNCTION CONNECTOR)
12.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU - CAN JUNCTION CONNECTOR)
a.
C292382C23
0.604,0.396 1.01,0.667 0.406,0.271 0.552,1.979 0.698,1.979 0.698,1.979 0.771,1.573 true 1.167,2 1.01,2 1.01,2 0.875,1.552 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.75,0.469 1.208,0.667 0.458,0.198 10 false I7 1.24,1.938 1.854,2.135 0.615,0.198 10 false CANH 0.198,1.917 0.813,2.115 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-21 (CANH) - I7-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

13.CONNECT CONNECTOR
a.

Reconnect the G292 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR OPEN IN CAN BUS WIRE (CAN JUNCTION TERMINAL - CAN JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS WIRE (CAN JUNCTION TERMINAL - CAN JUNCTION CONNECTOR)
a.
C369111C19
1.479,0.292 2,0.563 0.521,0.271 1.948,1.115 2.167,0.604 2.167,0.604 2.365,0.604 true 1.75,1.229 2.115,1.771 2.115,1.771 2.313,1.771 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 2.406,0.542 2.865,0.76 0.458,0.219 10 false CANH 2.354,1.708 2.813,1.927 0.458,0.219 10 false CANL 1.583,0.354 2.042,0.573 0.458,0.219 10 false G300
*a Rear view of wire harness connector
(to CAN Junction Terminal)


Disconnect the CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G300-3 (CANH) - G300-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

15.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR)
a.
C379589C42
0.146,1.583 0.625,1.844 0.479,0.26 1.052,1.688 1.052,0.688 1.052,0.688 0.885,0.688 true 1.219,1.688 1.219,0.521 1.219,0.521 1.052,0.521 true 1.385,1.688 1.385,0.354 1.385,0.354 1.219,0.354 true 1.552,1.688 1.552,0.354 1.552,0.354 1.719,0.354 true 1.719,1.688 1.719,0.521 1.719,0.521 1.885,0.521 true 1.875,1.688 1.875,0.771 1.875,0.771 2.042,0.771 true 1.052,2.052 1.052,2.833 1.052,2.833 0.885,2.833 true 1.219,2.063 1.219,3 1.219,3 1.052,3 true 1.385,2.042 1.385,3.208 1.385,3.208 1.219,3.208 true 1.573,2.063 1.573,3.229 1.573,3.229 1.74,3.229 true 1.719,2.073 1.719,2.99 1.719,2.99 1.885,2.99 true 1.906,2.052 1.906,2.719 1.906,2.719 2.073,2.719 true 0.229,1.635 0.844,1.833 0.615,0.198 10 false G292 1.781,0.281 2.698,0.479 0.917,0.198 10 false CANH*e 2.115,2.667 3.031,2.865 0.917,0.198 10 false CANL*g 0.052,0.083 0.969,0.281 0.917,0.198 10 false *a 0.313,0.604 1.229,0.802 0.917,0.198 10 false CANH*b 0.5,0.438 1.417,0.635 0.917,0.198 10 false CANH*c 0.656,0.271 1.573,0.469 0.917,0.198 10 false CANH*d 1.927,0.458 2.844,0.656 0.917,0.198 10 false CANH*f 2.094,0.698 3.01,0.896 0.917,0.198 10 false CANH*g 0.354,2.76 1.271,2.958 0.917,0.198 10 false CANL*b 0.521,2.927 1.438,3.125 0.917,0.198 10 false CANL*c 0.688,3.125 1.604,3.323 0.917,0.198 10 false CANL*d 1.813,3.167 2.729,3.365 0.917,0.198 10 false CANL*e 1.938,2.906 2.854,3.104 0.917,0.198 10 false CANL*f
*a Front view of wire harness connector
(to CAN Junction Connector)
*b to Side Televition Camera Assembly RH
*c to Parking Assist ECU
*d to Rear Television Camera Aseembly
*e to CAN Junction Terminal
*f to Side Televition Camera Assembly LH
*g to Front Television Camera Aseembly


Disconnect the CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G292-2 (CANH) - G292-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Side televition camera assembly RH
G292-3 (CANH) - G292-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Parking assist ECU
G292-4 (CANH) - G292-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera aseembly
G292-5 (CANH) - G292-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω CAN Junction Terminal
G292-6 (CANH) - G292-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Side televition camera assembly LH
G292-7 (CANH) - G292-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Front television camera aseembly



Result:
Result Proceed to
OK A
NG (Parking assist ECU CAN main wire) B
NG (CAN junction terminal CAN main wire) C
NG (Wire to sensor) D



A

REPLACE CAN JUNCTION CONNECTOR

B

16.CONNECT CONNECTOR

C

18.CONNECT CONNECTOR

D

25.CHECK FOR SHORT IN CAN BUS WIRES (SENSOR)
16.CONNECT CONNECTOR
a.

Reconnect the G292 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU - CAN JUNCTION CONNECTOR)
17.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU - CAN JUNCTION CONNECTOR)
a.
C292382C23
0.604,0.396 1.01,0.667 0.406,0.271 0.552,1.979 0.698,1.979 0.698,1.979 0.771,1.573 true 1.167,2 1.01,2 1.01,2 0.875,1.552 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.75,0.469 1.208,0.667 0.458,0.198 10 false I7 1.24,1.938 1.854,2.135 0.615,0.198 10 false CANH 0.198,1.917 0.813,2.115 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-21 (CANH) - I7-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

18.CONNECT CONNECTOR
a.

Reconnect the G292 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

19.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION TERMINAL - CAN JUNCTION CONNECTOR)
19.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION TERMINAL - CAN JUNCTION CONNECTOR)
a.
C369111C19
1.479,0.292 2,0.563 0.521,0.271 1.948,1.115 2.167,0.604 2.167,0.604 2.365,0.604 true 1.75,1.229 2.115,1.771 2.115,1.771 2.313,1.771 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 2.406,0.542 2.865,0.76 0.458,0.219 10 false CANH 2.354,1.708 2.813,1.927 0.458,0.219 10 false CANL 1.583,0.354 2.042,0.573 0.458,0.219 10 false G300
*a Rear view of wire harness connector
(to CAN Junction Terminal)


Disconnect the No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G300-3 (CANH) - G300-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

20.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION CONNECTOR)
a.
C379604C46
0.104,1.281 0.604,1.521 0.5,0.24 0.25,3.479 0.75,3.719 0.5,0.24 2.406,4.333 2.24,4.333 2.24,4.333 2.24,3.833 true 1.052,0.427 1.219,0.427 1.219,0.427 1.219,1.344 true 1.469,4.26 1.635,4.26 1.635,4.26 1.635,3.51 true 0.875,0.594 1.042,0.594 1.042,0.594 1.042,1.344 true 1.208,0.198 1.375,0.198 1.375,0.198 1.375,1.365 true 1.729,0.26 1.563,0.26 1.563,0.26 1.563,1.344 true 1.906,0.438 1.74,0.438 1.74,0.438 1.74,1.354 true 2.063,0.604 1.896,0.604 1.896,0.604 1.896,1.354 true 1.229,2.573 1.396,2.573 1.396,2.573 1.396,1.74 true 0.885,2.083 1.052,2.083 1.052,2.083 1.052,1.719 true 1.052,2.313 1.219,2.313 1.219,2.313 1.219,1.729 true 1.729,2.625 1.563,2.625 1.563,2.625 1.563,1.708 true 1.875,2.385 1.708,2.385 1.708,2.385 1.708,1.719 true 2.052,2.135 1.885,2.135 1.885,2.135 1.885,1.719 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a 0.125,2.927 0.438,3.125 0.313,0.198 10 false *b 0.188,1.333 0.656,1.531 0.469,0.198 10 false G292 0.365,3.521 0.75,3.719 0.385,0.198 10 false G48 2.458,4.24 2.844,4.438 0.385,0.198 10 false BAT 1.927,2.323 2.479,2.521 0.552,0.198 10 false CANL*g 2.115,0.531 2.896,0.781 0.781,0.25 10 false CANH*h 1.875,0.177 2.427,0.375 0.552,0.198 10 false CANH*f 0.281,0.552 0.833,0.75 0.552,0.198 10 false CANH*c 0.333,1.99 0.885,2.188 0.552,0.198 10 false CANL*c 0.469,2.25 1.021,2.448 0.552,0.198 10 false CANL*d 0.667,2.51 1.219,2.708 0.552,0.198 10 false CANL*e 1.219,4.208 1.604,4.406 0.385,0.198 10 false CG 0.469,0.365 1.021,0.563 0.552,0.198 10 false CANH*d 0.656,0.125 1.208,0.323 0.552,0.198 10 false CANH*e 1.938,0.375 2.49,0.573 0.552,0.198 10 false CANH*g 1.854,2.552 2.406,2.75 0.552,0.198 10 false CANL*f 2.115,2.063 2.885,2.271 0.771,0.208 10 false CANL*h
*a Front view of wire harness connector
(to CAN Junction Connector)
*b Front view of DLC3
*c to Side Televition Camera Assembly RH
*d to Parking Assist ECU
*e to Rear Television Camera Aseembly
*f to CAN Junction Terminal
*g to Side Televition Camera Assembly LH
*h to Front Television Camera Aseembly


Disconnect the CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G292-2 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Side televition camera assembly RH
G292-13 (CANL) - G48-4 (CG)
G292-2 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G292-13 (CANL) - G48-16 (BAT)
G292-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Parking assist ECU
G292-14 (CANL) - G48-4 (CG)
G292-3 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G292-14 (CANL) - G48-16 (BAT)
G292-4 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Rear television camera aseembly
G292-15 (CANL) - G48-4 (CG)
G292-4 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G292-15 (CANL) - G48-16 (BAT)
G292-5 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher CAN Junction Terminal
G292-16 (CANL) - G48-4 (CG)
G292-5 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G292-16 (CANL) - G48-16 (BAT)
G292-6 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Side televition camera assembly LH
G292-17 (CANL) - G48-4 (CG)
G292-6 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G292-17 (CANL) - G48-16 (BAT)
G292-7 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Front television camera aseembly
G292-18 (CANL) - G48-4 (CG)
G292-7 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G292-18 (CANL) - G48-16 (BAT)


Result:
Result Proceed to
OK A
NG (Parking assist ECU CAN main wire) B
NG (CAN junction terminal CAN main wire) C
NG (Wire to sensor) D




A

REPLACE CAN JUNCTION CONNECTOR

B

21.CONNECT CONNECTOR

C

23.CONNECT CONNECTOR

D

25.CHECK FOR SHORT IN CAN BUS WIRES (SENSOR)
21.CONNECT CONNECTOR
a.

Reconnect the G292 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU - CAN JUNCTION CONNECTOR)
22.CHECK FOR SHORT IN CAN BUS WIRES (PARKING ASSIST ECU - CAN JUNCTION CONNECTOR)
a.
E382444C01
1.5,0.219 1.917,0.479 0.417,0.26 1.552,1.833 1.969,2.094 0.417,0.26 1.26,1.635 1.094,1.635 1.094,1.635 0.844,1.146 true 0.5,1.667 0.667,1.667 0.667,1.667 0.75,1.167 true 2.635,3.208 2.469,3.208 2.469,3.208 2.25,2.854 true 1.188,2.063 1.354,2.063 1.354,2.063 1.656,2.469 true 1.646,0.24 1.958,0.438 0.313,0.198 10 false I7 1.625,1.906 1.938,2.104 0.313,0.198 10 false G48 1.333,1.563 1.948,1.75 0.615,0.188 10 false CANH 0.094,1.573 0.708,1.76 0.615,0.188 10 false CANL 2.677,3.135 3.292,3.323 0.615,0.188 10 false BAT 0.896,1.979 1.51,2.167 0.615,0.188 10 false CG 0.146,0.177 0.76,0.365 0.615,0.188 10 false *a
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-21 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
I7-20 (CANL) - G48-4 (CG)
I7-21 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I7-20 (CANL) - G48-16 (BAT)



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

23.CONNECT CONNECTOR
a.

Reconnect the G292 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION TERMINAL - CAN JUNCTION CONNECTOR)
24.CHECK FOR SHORT IN CAN BUS WIRES (CAN JUNCTION TERMINAL - CAN JUNCTION CONNECTOR)
a.
C300870C23
0.396,0.917 0.823,1.208 0.427,0.292 0.438,2.542 0.823,2.792 0.385,0.25 1.354,2.042 1.469,2.042 1.469,2.042 1.656,2.427 true 1.01,0.365 1.125,0.365 1.125,0.365 1.365,0.813 true 1.979,0.375 1.844,0.375 1.844,0.375 1.729,0.823 true 2.667,3.115 2.521,3.115 2.521,3.115 2.26,2.885 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 0.083,1.719 0.396,1.875 0.313,0.156 10 false *b 0.438,0.969 0.948,1.458 0.51,0.49 10 false G300 0.521,2.594 0.833,2.75 0.313,0.156 10 false G48 0.615,0.292 1.104,0.573 0.49,0.281 10 false CANH 2.042,0.313 2.573,0.656 0.531,0.344 10 false CANL 1.125,1.99 1.552,2.146 0.427,0.156 10 false CG 2.74,3.063 3.167,3.219 0.427,0.156 10 false BAT
*a Rear view of wire harness connector
(to CAN Junction Terminal)
*b Front view of DLC3


Disconnect the CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G300-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G300-2 (CANL) - G48-4 (CG)
G300-3 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G300-2 (CANL) - G48-16 (BAT)



Result:
Proceed to
OK
NG



OK

REPLACE CAN JUNCTION TERMINAL

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

25.CHECK FOR SHORT IN CAN BUS WIRES (SENSOR)
a.

Reconnect the wire harness connectors.


b.
C300870C23
0.396,0.917 0.823,1.208 0.427,0.292 0.438,2.542 0.823,2.792 0.385,0.25 1.354,2.042 1.469,2.042 1.469,2.042 1.656,2.427 true 1.01,0.365 1.125,0.365 1.125,0.365 1.365,0.813 true 1.979,0.375 1.844,0.375 1.844,0.375 1.729,0.823 true 2.667,3.115 2.521,3.115 2.521,3.115 2.26,2.885 true 0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 0.083,1.719 0.396,1.875 0.313,0.156 10 false *b 0.438,0.969 0.948,1.458 0.51,0.49 10 false G300 0.521,2.594 0.833,2.75 0.313,0.156 10 false G48 0.615,0.292 1.104,0.573 0.49,0.281 10 false CANH 2.042,0.313 2.573,0.656 0.531,0.344 10 false CANL 1.125,1.99 1.552,2.146 0.427,0.156 10 false CG 2.74,3.063 3.167,3.219 0.427,0.156 10 false BAT
*a Rear view of wire harness connector
(to CAN Junction Terminal)
*b Front view of DLC3


Disconnect the connector that includes terminals CANH and CANL from the sensor to which the short circuited main/branch line is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G300-3 (CANH) - G300-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
G300-3 (CANH) - G48-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G300-2 (CANL) - G48-4 (CG)
G300-3 (CANH) - G48-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G300-2 (CANL) - G48-16 (BAT)


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short to CAN bus lines in the sensor.

·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the sensor, there may be a short to B+ in the sensor.

·

If the resistance changes to 200 Ω or higher when the connector is disconnected from the sensor, there may be a short to GND in the sensor.

·

If the resistance does not become normal when the connector is disconnected from the sensor, check for a short circuit in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Proceed to
OK
NG



OK

REPLACE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR