Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260967 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when the switch is continuously depressed occurs.

Therefore, the radio receiver assembly cannot be operated using the steering pad switch assembly, and the radio receiver assembly itself cannot function.

WIRING DIAGRAM

E377084E04
0.677,1.573 1.104,1.781 0.427,0.208 10 false VOL- 1.375,1.573 1.802,1.781 0.427,0.208 10 false VOL+ 2.021,1.573 2.521,1.792 0.5,0.219 10 false SEEK- 2.688,1.573 3.281,1.792 0.594,0.219 10 false SEEK+ 0.604,2.531 1.083,2.74 0.479,0.208 10 false VOICE 2,2.427 2.5,2.813 0.5,0.385 10 false ON HOOK 1.323,2.406 1.823,2.792 0.5,0.385 10 false OFF HOOK 6.208,1.083 6.677,1.281 0.469,0.198 10 false SW1 1.563,3.333 2.604,3.563 1.042,0.229 10 false for LH Side 1.115,3.927 3.438,4.156 2.323,0.229 10 false Steering Pad Switch Assembly 3.948,3.948 5.052,4.448 1.104,0.5 10 false Spiral Cable Sub-assembly 6.073,4.135 7.021,4.552 0.948,0.417 10 false Radio Receiver Assembly 6.073,3.948 6.375,4.115 0.302,0.167 10 false H47 6.208,3 6.677,3.198 0.469,0.198 10 false SW2 6.208,2.042 6.677,2.24 0.469,0.198 10 false SWG 5.917,0.958 6.135,1.167 0.219,0.208 10 false 21 5.917,1.906 6.135,2.115 0.219,0.208 10 false 23 5.917,2.844 6.135,3.052 0.219,0.208 10 false 22 4.729,1.073 5.104,1.281 0.375,0.208 10 false G208 4.74,2.031 5.115,2.24 0.375,0.208 10 false G208 4.75,2.979 5.125,3.188 0.375,0.208 10 false G208 4.875,0.844 5.094,1.052 0.219,0.208 10 false 6 4.875,1.802 5.094,2.01 0.219,0.208 10 false 3 4.854,2.75 5.073,2.958 0.219,0.208 10 false 5 3.802,1.063 4.177,1.271 0.375,0.208 10 false z16 3.781,2.021 4.156,2.229 0.375,0.208 10 false z16 3.802,2.979 4.177,3.188 0.375,0.208 10 false z16 3.854,0.844 4.073,1.052 0.219,0.208 10 false 11 3.885,1.781 4.104,1.99 0.219,0.208 10 false 8 3.833,2.781 4.052,2.99 0.219,0.208 10 false 10 2.688,2.521 3.281,2.74 0.594,0.219 10 false MODE 4.26,0.969 4.729,1.167 0.469,0.198 10 false AU1 4.26,1.938 4.729,2.135 0.469,0.198 10 false EAU 4.271,2.875 4.74,3.073 0.469,0.198 10 false AU2

CAUTION / NOTICE / HINT

CAUTION:
·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the SRS (See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the H47 radio receiver assembly connector.


b.

Disconnect the G208 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H47-21 (SW1) - G208-6 (AU1) Always Below 1 Ω
H47-22 (SW2) - G208-5 (AU2) Always Below 1 Ω
H47-23 (SWG) - G208-3 (EAU) Always Below 1 Ω
H47-21 (SW1) - Body ground Always 10 kΩ or higher
H47-22 (SW2) - Body ground Always 10 kΩ or higher
H47-23 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR