Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type) › 2017.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260967 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the headlight dimmer switch is in the tail or head position.

WIRING DIAGRAM

E377085E06
1.354,0.521 2.406,0.76 1.052,0.24 10 false from TAIL Relay 3.313,0.688 3.875,0.885 0.563,0.198 10 false PANEL 6.167,3.031 6.563,3.229 0.396,0.198 10 false ILL+ 6.156,6.042 6.656,6.271 0.5,0.229 10 false GND1 6.146,5.083 6.625,5.281 0.479,0.198 10 false SWG 5.76,3.021 6.24,3.219 0.479,0.198 10 false H46 5.802,2.813 6.281,3.01 0.479,0.198 10 false 10 5.76,5.083 6.24,5.281 0.479,0.198 10 false H47 5.813,4.844 6.292,5.042 0.479,0.198 10 false 23 5.76,6.031 6.24,6.229 0.479,0.198 10 false H46 5.823,5.792 6.302,5.99 0.479,0.198 10 false 7 6.146,6.615 7.156,7.063 1.01,0.448 10 false Radio Receiver Assembly 4.094,3.021 4.656,3.219 0.563,0.198 10 false G208 4.198,2.792 4.76,2.99 0.563,0.198 10 false 13 4.094,5.083 4.656,5.281 0.563,0.198 10 false G208 4.25,4.875 4.813,5.073 0.563,0.198 10 false 3 2.813,3.021 3.375,3.219 0.563,0.198 10 false z16 2.844,5.094 3.406,5.292 0.563,0.198 10 false z16 2.917,4.896 3.104,5.083 0.188,0.188 10 false 8 2.885,2.813 3.073,3 0.188,0.188 10 false 5 3.448,2.875 3.844,3.073 0.396,0.198 10 false IL+2 3.469,4.969 3.865,5.167 0.396,0.198 10 false EAU 3.104,5.927 4.177,6.417 1.073,0.49 10 false Spiral Cable Sub-assembly 0.406,6.635 2.51,7.125 2.104,0.49 10 false Steering Pad Switch Assembly 0.969,6.156 1.813,6.375 0.844,0.219 10 false for RH Side 1,3.729 1.844,3.948 0.844,0.219 10 false for LH Side

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



HINT:

When replacing the radio receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the headlight dimmer switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, steering pad switch, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)

B

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL)
a.
U166423E02
2.583,1.823 2.396,1.823 2.396,1.823 2.063,1.51 true 0.083,0.042 0.396,0.24 0.313,0.198 10 false *a 1.51,0.219 1.948,0.417 0.438,0.198 10 false G208 2.625,1.698 3.24,1.896 0.615,0.198 10 false IL+2

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G208-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the H46 and H47 radio receiver assembly connectors.


b.

Disconnect the G208 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H47-23 (SWG) - G208-3 (EAU) Always Below 1 Ω
H46-7 (GND1) - Body ground Always Below 1 Ω
H47-23 (SWG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U149444E02
2.323,1.396 2.5,1.823 2.5,1.823 2.76,1.823 false 1.573,1.396 1.396,1.823 1.396,1.823 1.125,1.823 false 1.552,0.323 1.844,0.51 0.292,0.188 10 false H46 0.052,0 0.344,0.188 0.292,0.188 10 false *a 2.781,1.729 3.146,1.917 0.365,0.188 10 false ILL+ 0.615,1.729 1.031,1.917 0.417,0.188 10 false GND1

Disconnect the radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H46-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR