Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U029D  Lost Communication with NOx Sensor "A"  


DESCRIPTION

The ECM sends and receives data to and from the No. 1 nitrogen oxides sensor via local CAN communication.

U029D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Turn the engine switch on (IG) and wait for 1 seconds or more. Communication stops between the ECM and the No. 1 nitrogen oxides sensor for 1 seconds or more.
(1 trip detection logic)
·

No. 1 nitrogen oxides sensor

·

Harness or connector

·

ECM



MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the No. 1 nitrogen oxides sensor and ECM.

WIRING DIAGRAM

A420050E02
3.188,5.427 3.802,5.625 0.615,0.198 10 false C181 3.198,5.583 5.74,5.833 2.542,0.25 10 false No. 1 Nitrogen Oxides Sensor 3.094,1.323 3.708,1.521 0.615,0.198 10 false s6 3.052,1.51 5.594,1.76 2.542,0.25 10 false No. 2 Nitrogen Oxides Sensor 3.302,3.49 5.844,3.74 2.542,0.25 10 false Particulate Matter Sensor 3.594,2.365 4.208,2.563 0.615,0.198 10 false GND 3.594,1 4.208,1.198 0.615,0.198 10 false GND 3.604,0.458 4.219,0.656 0.615,0.198 10 false BATT 4.25,0.458 4.865,0.656 0.615,0.198 10 false CAN+ 4.26,0.823 4.875,1.021 0.615,0.198 10 false CAN- 4.281,2.344 4.896,2.542 0.615,0.198 10 false CAN+ 4.323,2.979 4.938,3.177 0.615,0.198 10 false CAN- 4.281,4.573 4.896,4.771 0.615,0.198 10 false CAN+ 4.302,4.99 4.917,5.188 0.615,0.198 10 false CAN- 3.99,7.135 5.375,7.323 1.385,0.188 10 false EFI-MAIN NO. 3 3.594,2.958 4.208,3.156 0.615,0.198 10 false BATT 3.594,4.729 4.208,4.927 0.615,0.198 10 false GND 3.604,4.354 4.219,4.552 0.615,0.198 10 false ADSW* 3.313,3.292 3.927,3.49 0.615,0.198 10 false s8 3.385,2.219 3.542,2.417 0.156,0.198 10 false 4 3.396,2.844 3.552,3.042 0.156,0.198 10 false 1 4.771,2.177 4.927,2.375 0.156,0.198 10 false 2 4.781,4.802 4.938,5 0.156,0.198 10 false 3 4.76,2.792 4.917,2.99 0.156,0.198 10 false 3 4.802,4.396 4.958,4.594 0.156,0.198 10 false 2 3.354,4.24 3.51,4.438 0.156,0.198 10 false 1 3.375,4.594 3.531,4.792 0.156,0.198 10 false 4 3.365,4.979 3.521,5.177 0.156,0.198 10 false 5 3.365,0.844 3.521,1.042 0.156,0.198 10 false 2 3.365,0.333 3.521,0.531 0.156,0.198 10 false 1 4.76,0.281 4.917,0.479 0.156,0.198 10 false 4 4.771,0.656 4.927,0.854 0.156,0.198 10 false 3 1.417,6.208 2.031,6.406 0.615,0.198 10 false NOx PM 2.073,5.771 2.229,5.969 0.156,0.198 10 false 1 2.073,4.979 2.229,5.177 0.156,0.198 10 false 3 1.208,4.969 1.365,5.167 0.156,0.198 10 false 5 1.219,5.771 1.375,5.969 0.156,0.198 10 false 2 2.354,4.042 3.427,4.24 1.073,0.198 10 false NOx RR PM 2.479,5.281 3.552,5.479 1.073,0.198 10 false NOx FR 5.688,4.406 5.948,4.615 0.26,0.208 10 false 27 5.698,4.833 5.958,5.042 0.26,0.208 10 false 35 5.99,5.021 6.604,5.219 0.615,0.198 10 false CAND 5.99,4.583 6.604,4.781 0.615,0.198 10 false CANU 6,7.396 6.615,7.594 0.615,0.198 10 false MREL 6.208,8.198 6.823,8.396 0.615,0.198 10 false G184 6.229,8.333 6.844,8.531 0.615,0.198 10 false ECM 5.021,7.208 5.177,7.406 0.156,0.198 10 false 8 5.01,6.792 5.167,6.99 0.156,0.198 10 false 2 5.708,7.198 5.969,7.406 0.26,0.208 10 false 14 3.156,7.719 4.542,7.906 1.385,0.188 10 false EFI-MAIN NO. 1 2.302,7.104 3.688,7.292 1.385,0.188 10 false EFI-MAIN NO. 1 1.885,7.385 2.198,7.583 0.313,0.198 10 false 1W 1.906,6.979 2.219,7.177 0.313,0.198 10 false 1S 4.927,6.969 5.24,7.167 0.313,0.198 10 false 1W 4.938,7.375 5.25,7.573 0.313,0.198 10 false 1W 1.958,6.76 2.115,6.958 0.156,0.198 10 false 1 1.979,7.188 2.135,7.385 0.156,0.198 10 false 4 2.833,8.156 4.896,8.344 2.063,0.188 10 false No. 1 Integration Relay 2.323,8.385 4.385,8.573 2.063,0.188 10 false : CAN Communication Line 0.896,7.135 1.51,7.333 0.615,0.198 10 false 70A FL 0.542,6.323 1.156,6.521 0.615,0.198 10 false 250A FL 0.677,5.25 1.323,5.448 0.646,0.198 10 false NOx PM 2.844,4.938 3,5.135 0.156,0.198 10 false 2 2.458,4.938 2.635,5.135 0.177,0.198 10 false 1 2.115,4.229 2.292,4.427 0.177,0.198 10 false 1 2.104,3.865 2.26,4.063 0.156,0.198 10 false 2 0.688,7.844 1.302,8.042 0.615,0.198 10 false Battery 3.604,5.104 4.219,5.302 0.615,0.198 10 false BATT 4.906,5.281 6.969,5.469 2.063,0.188 10 false *: -2018/12

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK NO. 1 NITROGEN OXIDES SENSOR (BATT TERMINAL)
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A430900C01
1.406,0.219 2,0.542 0.594,0.323 0.979,1.979 1.125,1.979 1.125,1.979 1.281,1.5 true 1.75,1.969 1.615,1.969 1.615,1.969 1.5,1.51 true 1.552,0.302 2.177,0.5 0.625,0.198 10 false C181 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.813,1.896 2.271,2.094 0.458,0.198 10 false GND 0.615,1.896 1.073,2.094 0.458,0.198 10 false BATT
*a Front view of wire harness connector
(to No. 1 nitrogen oxides sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V




OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 NITROGEN OXIDES SENSOR - ECM)

NG

6.INSPECT NOX PM RELAY
2.CHECK HARNESS AND CONNECTOR (NO. 1 NITROGEN OXIDES SENSOR - ECM)
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-2 (CAN+) - G184-27 (CANU) Always Below 1 Ω
C181-3 (CAN-) - G184-35 (CAND) Always Below 1 Ω
C181-2 (CAN+) or G184-27 (CANU) - Body ground and other terminals Always 10 kΩ or higher
C181-3 (CAN-) or G184-35 (CAND) - Body ground and other terminals Always 10 kΩ or higher




OK

3.REPLACE NO. 1 NITROGEN OXIDES SENSOR

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL

HINT:

Perform "A/F Sensor Compensation Reset" after replacing the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION




NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.



d.

Turn the engine switch off for 30 seconds.



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) wait for 1 seconds or more.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
DTC U029D is output B




A

END

B

6.INSPECT NOX PM RELAY

OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 NITROGEN OXIDES SENSOR - NOX PM RELAY - NO. 1 INTEGRATION RELAY)

NG

REPLACE NOX PM RELAY

7.CHECK HARNESS AND CONNECTOR (NO. 1 NITROGEN OXIDES SENSOR - NOX PM RELAY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Remove the NOx PM relay from the engine relay block.


c.

Remove the No. 1 integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-5 (BATT) - NOx PM relay terminal 3 Always Below 1 Ω
C181-4 (GND) - Body ground Always Below 1 Ω
NOx PM relay terminal 2 - Body ground Always Below 1 Ω
NOx PM relay terminal 1 - 1W-2 Always Below 1 Ω
NOx PM relay terminal 3 or C181-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
NOx PM relay terminal 5 - Body ground Always 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR